ender 3 pro cable management 3d models

This is a remix: https://www.thingiverse.com/thing:3769941 With these 3 pieces you will have your cable chain complete and well aligned. ...

Cable guide for the bed of the ender 3, with this mod you can bring the printer closer to the wall without disturbing the cable. Gain space with this mod, very easy to assemble, a support for the bed, another for the base and the chain. ... You use the...

After installing a Creality Sprite Extruder Pro on my Ender 3 Pro, I was frustrated that the only cable management solution I could find for the large ribbon cable was using a zip-tie to attach it to the X carriage where the Bowden extruder used to...

With my Ender 3 Pro now sporting a metal extruder upgrade, I had to carefully trim the printed piece on the corner facing the bolt head so it would fit snugly underneath. ... I decided to use this chance to learn how to edit STL files for this...

IF u know how,and u are able, i suggest u to cable-manage entirelly your ender 3 before put on the chain, but if u are not experienced in it, just avoid to move cables too much. IN the E-Mount there is a hole (watch photos) that u could use to pass...

The Air Handling is Tightened, Noise-Causing Grille Removed, New Fabric Sleeve Ports Added (https://www.thingiverse.com/thing:3994402), Increased Case Volume, and Cable Management - Both Inside and Outside - Included. Inside, I've Cleared Out the...

3 x 2 /3 mm cable ties to secure the cables. The wires on the hot end, 2 fans and the Thermistor should be cut no longer than 445mm (17-1/4") when measured from the top of the fan cover. The rest of the wires should be long enough to reach from...

I'm creating a cable management system for my Creality cr20 pro by attaching it to the bed bracket using Ender 3 Cable Chain, which I modified to fit by widening the last link holes with a 4mm drill and replacing the back corner case screw with a...

Two versions are provided here; the first is "v2.1" and features a cutout in the side for filament savings, three holes, and cable management clips. This version is recommended if you can work with the three holes, as my camera's cables fit...

I've added mounting posts on the interior sides and bottom for cable management, etc. The Cable Hold Downs are intended to attach to the interior mounts with M3 bolts. Only the Left Covers need support. It should easily house: Creality stock boards,...

This is a little mounting device for an ID retractor to mount it to your printer frame (CR-10, Ender 3 or similar) using an m5 bolt and a t-nut. The ID retractor will be attached to the front hook and will hold the cables out and back. ...Nice handy...

This is a little mounting device for an ID retractor to mount it to your printer frame (CR-10, Ender 3 or similar) using an m5 bolt and a t-nut. The ID retractor will be attached to the front hook and will hold the cables out and back. ... Nice handy...

Ender 3 Pro Upgrade Guide to Cable Chain Ends for Filament Feed

Two Trees Sapphire Pro PTFE Tube and Carriage Cable Management (remix) To mount this part I used the 4 existing screws. To fasten the cables use zip ties in two places. 3 walls. Layer height 0.2 mm. ...Infill 50-100%.

Here is the rewritten text: For Enders 3, use the original filament detector version, adapting only the fixing part.

This is a webcam mount that can be installed at the front centre of the Creality Ender 3 V2 printer by removing and replacing the two existing M5x8mm screws with M5x30mm screws and by using a metal Camera Hot Shoe Mount Adapter like the following...

Ender 3 S1 Pro Drag Cable Chain Snap link. ...Link that snaps into stock ender 3 S1 pro cable slot. made to attach cable chain to the awkward ender 3 s1 pro cable mounts Printing at 10% scale should match the other pieces24x37.84x15.2mm

This is a cable management solution for the outstanding direct-drive design by Capacitor, which disappointingly lacks any effective cable organization system. Simply place a spacer between the motor and extruder without reprinting the extruder mount,...

The Creality Ender 3 Pro boasts an advanced cable management system that keeps the heating bed organized and clutter-free. By thoughtfully routing cables along the frame, users can maintain a clear workspace and prevent tangles or damage to the...

Set of 2 brackets to attach the electrical cables when adding a Direct-Drive kit to an Ender 3 (Pro).

Just a little tool to mount your webcam cable or whatever cable to the filament holder that is included with the Ender 3 SP1 Pro printer.

This Cable Management System for Ender-5 and Ender-5 Pro was designed to hide and secure the great majority of its cables. To use it you need to extend some of the cables. Very simple procedure it you already used soldering irons. It is not a...

Remixed from [rbuckton](https://www.thingiverse.com/rbuckton)s [Sprite Extruder Pro parallel cable harness for Ender 3/Pro](https://www.thingiverse.com/thing:5821776) to fit the deeper x gantry bracket of the Ender 3 Max

Strengthened zip tie attachment points and added ramps where the cables transition onto and off the part, and it's slightly thicker.

A sleek three-part cable management system, designed specifically for the Sapphire Pro carriage. This innovative solution securely holds cables in place using two sturdy zip ties, while two strategically positioned holes enable easy integration of...

Fixed some slicing errors Simple Cable Management box to hide the cludder on the Ender 5 Plus. Wire pass-through on the back and bottom. ... The lid can be fastend with M3 Bolts Mounting holes to fix the box on the extrusion are provided Walls...

I'm experiencing some smoothness issues between the designs of Thingiverse's #3132855 and #2920060. ...This particular solution seems to resolve the problem effectively, as it leverages the standard hardware components.

I don´t have includet this part .let me know if it was packaged for you .

... S1 prov1 restricts x axis to260mmv2 allows for full extensionv3 is even smaller. ...I didn't test this one, just modeled itfor added stability, pair with snap link bellowhttps://www.printables.com/model/360429-ender-3-s1-pro-drag-cable-chain-snap-link

Been a little worried about the weak section of the extruder cable on my Ender 3 S-1 Pro, so I decided to make a little TPU support to reduce cable flex.