ender 3 pro cable management 3d models

 I was thinking about adding extension cables to my cables, and actually ordered the connectors I needed from Aliexpress, but then I was looking at a post about adding braces to the corners of the ender 5 (such as this set from dbltrbl023 or this one...

... model oriented as downloaded to print with no supports needed. All feedback is greatly appreciated. I've tested it on an Ender 3 Pro but assume it will work equally well on an Ender 3; it may also be compatible with other similar Creality printers.

... work. Print in the orientation as downloaded in order to print with no supports. All feedback is appreciated. I have an Ender 3 Pro, but I am assuming it will work on an Ender 3 as well. ...May also work with other similar Creality printers.

This protective cover/channel VENT secures cable entry to mainboard on the Ender3 Pro. This will seal off the hole where cables normally go into the control box, designed specifically for individuals who have modified their printer to relocate the...

Redesigned X Axis opposite side bracket to allow for referencing on glue up Additional Parts Needed: SonOvaSailor's Design: Print 1 - Heat bed plug link and 4 Chain Link Cover Long  found here https://www.thingiverse.com/thing:4570302/files...

Re-Design of Cable clip for Control box ribbon cable

More Ender 3 models at https://www.thingiverse.com/vampyrex13/collections/my-ender-3-models. Updates ------- • 2022.06.26: Ender 3 v2 mount added. • 2022.06.20: BLTouch & CR Touch Volcano hotend versions added. Klipper Firmware Notes ...

This is a protective cover/channel VENT for the cable entry to the mainboard on the Ender3 Pro. This will block the hole where the cables normally go into the control box, and is designed for people who have done mods to move their control box to the...

This is a filament guide I remixed from a few people I was having problems getting the best of both worlds (cable management and good filament guiding). So, I did it myself and made this great filament guide. One downside is you need a connector for...

... have to place it where the Z-axis end stop already is. Extra parts. Chassis mount: M4 x 12mm + T Nut (x 4) M4 x 30mm + Nut (x 2) Hotend mount: M3 x 8mm (x 2) or the same by Ender Chain cable carrier https://www.amazon.it/gp/product/B094ZSWDWB/

Simple cable holder for the Sprite ribbon cable.Mounted at the old bowden extruder motor location

The original design by @Stiggan2k is great, and I'm currently printing the chains as I type this, however I found was the part that attaches to the former extruder motor plate does not fit my Ender 3 Pro. Seems like the Ender 3 Pro has a different...

The original design by @Stiggan2k is great, and the chains work amazingly, however I found the part that attaches to the former extruder motor plate does not fit my Ender 3 Pro. It seems like the Ender 3 Pro has a different sized plate as the screw...

... the plate box. ...It keeps the cables tidy and tidy, improves the presence of the machine. The screws are M3. It is made of PETG but you can use any other material. It consists of the box, cover, hotend cable inlet cover and hotbed cable inlet cover.

Modified flat clamp to hold rear power cables to frame rails 6 Clamps 31 minutes to print

Hey, A super easy yet efficient solution to keep your printer cable organized. ... Take care, Omer.L

Design this clip to hold cable from moving and damaging the x-axis cables. I also added an offset to keep it away from the heat of the servo motor. Bracket holds using the nut shown in the picture. ... you can insert the cable and clip it back.

I loved these clips but recently i needed to cut my cable ties to rewire some bits, and i could not rethread a new cable tie at all. I made one remix with a solid bar across but i could not clip that on at all.... so i went with this version.

It's a remix from https://www.thingiverse.com/thing:5953410, but much stronger because my cable is harder than on the regular S1 printer.And also on my design is lot more space for cables.But the idea of the original design was very good and now it...

print this in two pieces, top and bottom. ... glue together. it snaps on to the Y motor cover. This supports the extruder cables. ...

This is a clamp/guide for a mod to the heated bed cable that may snag on the y axis stepper motor at the rear of the printer. Mine snagged from new so i made this to keep the cable straight. I printed draft low quality (0.28) in Cura 5 with std...

Makes the cable at a more vertical angle Still, it is not completely free of gantry interference. ... If the height of the molding exceeds approximately 220 mm, remove this adapter.

I needed a bracket to keep my cable from ending up like so many others I've heard. ...I took measurements from my own printer and created this in tinkercad.

I liked the way the cable chain fit from the base to the extruder, but i didn't want the chain to the hotend.Remixed the extruder mount to work with Creality Filament Runout Sensor Bracket.

A simple change in orientation of the “cable_chain_side_lock” file allows the cable chain to run cleanly down the left side of the printer bed toward the front of the printer making the entire machine about 5 or 6 inches smaller side-to-side given...

Roller guide for extruder cable, a simple setup that requires just two pieces of 1.75mm filament to secure the roller in place. To complete the project, be sure to print two separate rollers. ...If you need any modifications made to the design, feel...

To do so, you'll require a total of 18 cable links, 18 link clips, 2 wire clips, one wire holder, and the left chain holder bolts which should be placed over the original case by first loosening the two bolts on the existing setup, then positioning...

I got sick of looking at my wires just hanging around and wanted a low profile management system. Not the greatest design but my first. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/5OMwtd6dnkd

The original design by @Stiggan2k is great, and the chains work amazingly, however I found was the part that attaches to the former extruder motor plate does not fit my Ender 3 Pro. It seems like the Ender 3 Pro has a different sized plate as the...

Designed this to keep the wires on the ender 5 plus nice and neat. This is not a flimsy design, they are strong and keep wires well. The pieces attach to the extrusion with a couple screws and t nuts. They are the width of the extrusion so they...