ender 3 pro bltouch 3d models

Designed for the new batch of Creality Ender 3 Pro, the new batch are shipped with different size hole to use with the Creality BLTouch Kit. this design are properly measured with the new X Carriage. Feel Free to use and Happy Printing!! STL...

This print is a mount for the BLTouch/3DTouch sensor. The print is designed in such a way that it fits nicely over the existing screw holes. ... Nozzle ofset: x:-42, y:-10, z:-1,18

Теперь можно легко и просто установить датчик автоуровня (BL-Touch, 3D Touch) к этому креплению при переходе на директ. ...Проверено на Ender 3 Pro

The original mount holds up well but for my replica of the 3D Touch, I found that the placement was slightly too low down. In contrast, my modified version sits 1mm higher. I printed this using PETG with a solid 100% infill and a buildplate support...

Remixed from https://www.thingiverse.com/thing:4441076. Found the stock screws to be too short to properly mount, so I added a countersink. ...Also opened up the slot for the wires as I had difficulty running the dupont connectors through.

Add more structure for increased stability More stable bltouch mount to avoid deviations during probing. ... More holes for easier mounting of bltouch

Widened the bracket on eduardofcr's mount ([https://www.thingiverse.com/thing:3780371](link)) to accommodate the additional bracket to hold my BLTouch.

Thanks to Felix Ort for the bltouch drawing Thanks to Martin Csanaki for the noctua fans drawing Thanks to Nejc Tovornic for the hotend drawing Please do not pay attention to the cable management of my setup, i am busy changing the motherboard and...

Supports: Raspberry Pi 3 | 4x Buck Converters | Creality Boards or EZBoard Lite | Drill holes on top cover for EZABL Electronics Cases OR 2x Mosfets | 4x Buck Converters | Creality Boards or EZBoard Lite | EZABL Electronics Case v1, v2, v3, and Pro...

Adding the Sovol Creality Ender 3 Pro 32-bit Silent Board Motherboard V4.2.7 with TMC2225 Driver Marlin 2.0.1 for Ender-3 Pro really makes it quiet and provides connections for the BLTouch. The following video explains modification of the mounting...

Supports: Bowden Direct Drive Stock Extruder Direct Drive CR10s Pro Dual Gear Extruder https://www.amazon.com/gp/product/B07SY745CF Direct Drive Bondtech BMG EZABL v1, v2, v3, and Pro BLTouch Dual 5015 Fans Dual 4010 Fans Stock Hotend Micro Swiss...

After I changed nozzles to a slightly longer nozzle, the nozzle would crash into the bed when homing/probing. I designed this spacer to offset the probe slightly to compensate for the extra nozzle length. The spacer is 2mm thick which will work with...

<p>After I changed nozzles to a slightly longer nozzle, the nozzle would crash into the bed when homing/probing. I designed this spacer to offset the probe slightly to compensate for the extra nozzle length. The spacer is 2mm thick which will work...

Ender 3-E3 Pro BLTouch Mount.

I trimmed down the left side to accommodate the Official Creality Steel BLTouch Mount.

... listed. ...I wanted a side mount for my ender 3 proand to keed it at original spot UPDATE I prefered redesigning the side mount duct to allow the installation of the original bl touch mount for the ender 3 pro https://www.thingiverse.com/thing:5156237

A small friend to mount to the X-carriage of an Ender 3 Pro with BL Touch installed. ...May need some filing to ensure the edges fit on your specific mount.

Remix with added BLTouch support and removed led holes. ... Adjustable BLTouch support merged from https://www.thingiverse.com/thing:3586322

was a nice cable mount just now with a optional bltouch sensor option

... and given it a personal touch. ...I added 5mm dials to secure the BLTouch, carved out recesses where the print bed support rests against the ventilation duct of the Hotend, and incorporated a bracket that attaches to the X-axis to prevent deformation.

Introduction: Combining jckz82's fang and StevenMLawson's BLTouch mount, this remix adds an optional LED strip mount. The fang remains securely attached to the hotend by two screws that pass through it. Refer to the pictures for the correct printing...

Currently my latest version for Ender 3/Pro with 4 wheel cart (from Aliexpress) for Direct Drive and BLTouch. ...I lowered the height of the air tunnel a bit for better visibility of the hot end.

Ender 3/3Pro direct drive fanduct for Sunon 5015 and original hotend 4010 fan.

Ender 3/3Pro direct drive fanduct for Sunon 5015 and original hotend 4010 fan.

... if there's any problems. ... Use custom supports to not support the inside, only the outside where needed. Attention, it has been modified for the Hotend Creality Spider 300C Pro, for other Hotend Spider models a longer cooling duct may be required.

...I also added holes to the left lid for a TH3D Pro control box. Recently when ever I try to comment on something it flags it for moderation so if you comment I will try to respond but it probably won't go through. ... Category: 3D Printer Accessories

Additionally, holes have been added to the left lid for a TH3D Pro control box installation. Lately, whenever I attempt to comment on something, it flags my input for moderation. ...If you do manage to post a comment, I'll make every effort to respond...

BLtouch holder, fan holder and exhaust for hot end Ender 3 with direct drive.

The BLTouch mount on the original was about 15mm too heigh for my setup Lowered it a bit

... PETG or upgrade to superior ABS for exceptional results. ... The fan duct was carefully printed exactly as depicted in the thumbnail image screenshots. To ensure precise calibration of my BLTouch sensor, I set the offset values to X: -56.8 and Y: 0.