ender 3 print files 3d models

Ender 3 Auto Shutdown System ==================== [Discord](https://discord.gg/nHr7RV5) [Rosa Buy Button](http://bit.ly/2LMBt19) Polish Shop: http://bit.ly/2Xu2uIA [3D Print Slav](https://www.facebook.com/3DPrintSlav) Donate to BlackHideki via...

If the extruder has sufficient force to hold it, you can use the basic part on the ender 3 without using a separate filament guide. When opening or closing the door of the enclosure, do not use the hinged door. There is no choice but to make a gap...

No Commercial Ball Bearing Used, the Needle Bearing Model to Use for this Support is Available for Download Here: https://www.thingiverse.com/thing:2162376 Minimum Inner Diameter of Spool: 50mm Print - 2 Rollers - 2 Roller Axes - 1 Roll - 1 Support...

This design is based on fast printing time. ...The gcode file prints in 1h3m on my S1. Used regular PLA. ...

This Ender 5 Files Holder Remix is based on the Ender 5 Tool holder by @Buckwheat469_225347 on printables.com: https://www.printables.com/model/378849-ender-5-tool-holder-remix, which was remixed from TrigoKlei on Thingiverse:...

Ender 3 auto shutdown system. Polish shop here. Slav, simple, green, ecological device that not only will save you money but also reduce noise. A mechanism that will turn off your printer after its done printing, fully mechanical and does...

just slice and print away

Print your document in 2540 scale and lay it flat on the bed. ...Want a screen protector that shows you the print progress? ...Design one now!

I created a 3D model to address scarring issues on my printed surfaces, allowing for precise adjustments without significant time or material waste.

The print head is supported by a fixed attachment that holds three LED strips at a precise 30-degree angle, ensuring optimal visibility in low-light conditions.

Pre-cut model, ready to print on a 220 x 220 mm printer Model based on the green goblin from the tobey maguire movie 8 parts in total.

Tired of all the over engineered PSU brackets that take way to long to print ? I designed these simple brackets that print in little over an hour each. There is a gap between the PSU and the table due to airflow. ... I added an extra ground cable...

After printing, the printer adheres to max Y (250 mm) and breaks the voltage with the microswitch. ... command end-gcode: G4 S120; paus 120 s G0 Y230; to y-axle to 230

This is based on https://www.thingiverse.com/tonyguar usb holder but cut at the bottom to avoid using support or raft, it basically does the same function but print is easier.

I created these sleek designs that can be printed in under an hour each, making them a quick and efficient solution. The gap between the PSU and the table is intentionally left for airflow purposes. ...To ensure maximum safety, I've added an additional...

After printing, the printer strictly adheres to a maximum Z-axis height of 250 millimeters and breaks the voltage circuit with a built-in microswitch.\r\nCritical command end-gcode:\r\nG4 S300 enables a three-second delay before the print head moves...

The original duct was lower than my nozzle, so I shortened it. ...There are 2 versions, the "flat" one and the 2mm one. The flat one, once installed will be tilted to point down towards the print, the other will be perpendicular to the nozzle.

A easy to print and mount first slide the bracket over the back plate, then mount the bmg extruder. and then secure the v6 hotend with the fanduct in this model, the hotend is close to the backplate, so there is little ofset compared to the old...

... -need to extend the pen rack as it is currently not able to line up with the extruder. -may have to adjust pen cap size to fit new markers. (Experimenting with oil based markers as I've heard they do better on 3d prints. ... Etc....

Here's an upload of my Ender-2 Firmware Files for use with a BLTouch. ...I've also included the .STL for the [BLTouch mount](https://www.thingiverse.com/thing:5186908).

-- Originally designed by bvac I just broke out the STL files that were inside the .thing file to make it easier for people who don't use makerbots. Otherwise this is exactly the same as AnthonyM thing. ...All credit goes to bvac for the originals and...

-- Originally designed by bvac I just broke out the STL files that were inside the .thing file to make it easier for people who don't use makerbots. Otherwise this is exactly the same as AnthonyM thing. ... All credit goes to bvac for the originals and...

File format: STL Level of detail: Medium DISCLAIMER My prints are virtually tested in Cura with 0.10 mm layer height. Always have thicker walls than the standard setting to have some room for sanding & avoid fragile surfaces. Note that most of my...

File format: STL Level of detail: Medium DISCLAIMER My prints are virtually tested in Cura with 0.10 mm layer height. Always have thicker walls than the standard setting to have some room for sanding & avoid fragile surfaces. Note that most of my...

Here's the complete 3-ghost design that everyone has been looking forward to, brought to you by AnthonyM - he made sure it was up for grabs on Thingiverse even after all those years, which I really appreciate! ...All credit goes to bvac, who first...

If you have printed the model you can choose if you would like to upload a picture of your make. I would really love that! If you would like to know how i design a 2D picture (google) into a 3D model. ... Use this...

The total print time and print orientation are shown in the image (approx 3 hours). No rafts or support needed. Make sure to measure the thickness of the plate to be 2.5mm where it slides into. It will be a bit tight fit at first but once you...

Remix of the remix to fit ender 7, ender 5 and ender 3 v3 nozzels, (taller ones)I printed it at 105% to have a little loose for the nozzles, i think this or 103% is perfect

Three little beautiful houses. ...They look nice solo or in a small town. All are super easy to print and super easy to paint. No support is needed. Attention: You are purchasing only 3d printable files.

A simple holder for my needle files. ... This is a remix from @POLprints Ender 3 USB holder https://www.thingiverse.com/thing:3477587