ender 3 print bed size 3d models

Another Bed Handle. ...The handle can be fixed to the existing holes in the bed.

Next, carefully remove the print from the bed and measure its height using a vernier caliper. The measurement should be approximately 0.2mm. To further test different layer heights, try printing a new file at 0.20mm layer height using a 0.20mm...

I figured I need to try and level my print bed with precision when it's time, and after adding this mod to my printer, https://www.thingiverse.com/thing:3117234 is now a must-have for me. ...As another user has noted, if you start printing ABS or other...

A simple solution to change how the bed height is calculated so that swapping of build plate surfaces will be accounted for at the start of each print without any calibration after the initial setup. ...Please attach your revisions to this post so I can...

This design makes a significant upgrade over the original: https://www.thingiverse.com/thing:3962397 ADDITIONAL PARTS REQUIRED: * sg90 servo motor * micro switches, similar to these:...

The Easy Install Bed Handle Attaches Securely. ...The compact design fits seamlessly into the existing holes on your bed frame.

... regolazione. ...Spero vi piaccia, caio e alla prossima This is a useless, but valuable tool :-), to remind you in which direction you have to turn the screws of the printing bed, for its adjustment. ... I hope you like it, Bye and see you next time

I built a simple scrapper using TinkerCad, equipping it with a curved design that allows me to pry parts loose from the bed without lifting them. So far, this solution has worked flawlessly, prompting me to share my creation. I printed the scrapper...

A simple clip to ensure the bed knob doesn't move from where you set it. Clip onto bed knob, and forget. ...Now you always know where the last setting for the bed leveling knob was.

The Cable Chain mount: https://www.thingiverse.com/thing:3310252 The Camera Mount: https://www.thingiverse.com/thing:2842300 The Bed Mount: https://www.thingiverse.com/thing:3014982 This is my first "design" so feedback is welcome! ... This version...

Z Axis stop compensates for glass build plate thickness. ...Little to no bed leveling when installed.

Humans snuggle into their beds for a restful night's sleep.

Z Axis stop compensates for glass build plate thickness. ...Little to no bed leveling when installed.

A simple clip, long or short to clip the glass bed onto the main frame. ...I have the steel ones that came with the bed but they take up more room and these fit snug against it. ...

these are some bed clips for 7mm glass+bed thickness (they are actually 6.7) I made them in ABS and until now I had no problems at all cheers

Made the attached part half thick to work with the following bed locks: https://www.thingiverse.com/thing:4203563

... bed plate that features a slight angle. Unlike other designs, mine is more compact. This innovative handle attaches to the right side bed leveling wheel and tucks neatly out of the way if needed. ... To ensure stability, some supports are required.

Replacing the cable support for my bed was a straightforward task, with the spring inserting itself neatly from beneath, thus minimizing its tendency to disrupt the bedding at the rear. ...For added convenience, I opted to secure the assembly using only...

Created a bed trim wheel with a pocket for a 4mm nyloc nut. ... The industry standard 4mm thread pitch is 0.7mm per turn, so I put 7 marks around the periphery and each mark denotes 0.1mm of bed height adjustment.

... Raised Parts. ...I Designed This Attachment to Keep the Mat Flattened Against the Bed, Ensuring a Smooth Sleeping Surface. ...It's Not Intended to Replace the Stock Clips, But Rather to Provide Additional Support for a More Comfortable Night's Sleep.

I fabricated them at .1mm 90% infill for durability and utilized a 3mm nut with a nylon lock loosely so the bed screw has a slight play but secures the part firmly in place. ...I created a second pair with thermal filament, colored raspberry initially,...

This G-code includes four calibration points aligned with the heatbed's screw positions, as well as the bed's center. ...To proceed to the next point, press the LCD button.

This is a remix from gulfcoast_robotics. ...I just made room on the right side of the handle for the silicon bed spacers. ... I did mine at 100% infill because the wall near the right hole is much thinner.

This attaches to the bed under the leveling wheel on the front left side, then with 2 M3 Bolts and 2 M3 Nuts you can attach the ADXL345 to the mount. in the second picture you can see where this is going, just remove the nut and put the piece in,...

I wanted a handle for my printer bed but was disappointed that all of the options that I found could cause bed leveling problems. This handle does not touch the springs and instead grips on the shape of the y axis plate. Each handle also needs a clip...

There are countless bed handles out there, but this particular one steals the show as the most adorable of them all. It's sure to bring a smile to your face and make your day just a little bit brighter. ...Enjoy!

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I've got a laser sensor that's not working right, which I originally used as a bed leveling sensor for testing purposes. ...I have a few other sensors in reserve, including both capacitive and inductive types, but this one might be the best option since...

Always struggling to keep paper clips in place on the glass bed, this innovation promises to be the solution. ... (Sorry again to earlier downloaders, but an updated version has been made available, featuring straight clips that open on both ends - a...

Liked the original model, but don't need for camera mount. ...Made the spring cups same depth to match bed cable strain relief. Note: this was designed to fit springs up to 8mm in OD. ...Files ending _10.stl should work with 10mm OD springs