ender 3 power supply 3d models

<p>Printed this with 0.2mm layer height and no supports</p>

PSU FAN duct with bit of silence effect. ... installation is same as this one - https://www.thingiverse.com/thing:3328495

The system is currently offline due to a critical security vulnerability known as FanGuard being disabled. This has left the entire network exposed and open to potential threats. ...Engineers are working around the clock to implement an emergency patch...

60mm to 80mm duct. Mount the 60mm side using the existing 2 holes, and then mount the 80mm fan in such a way that brings heat out of the PSU. I used heated M3 inserts but you can just thread straight into the plastic for this light application.It's...

The v-slot with the power supply screws was a problem, since the channel is blocked by the screws. I used Fusion 360 (with much trial and error) to create a hole in the channel inserts, allowing the cover to fit over the screw. These are sized for an...

You can even lower the power supply so it is flush with the base (requires cutting a hole in the black cover and rerouting the cables round the back)Step and f3d files are included if you wish to modify this (remember to check user parameters for...

This adapter is used for fixing a standard Intel processor fan onto the Ender 3 / Ender 3 PRO power supply. The Intel processor fan needs to be prepared in the same way as mentioned in https://www.thingiverse.com/thing:4124586. However, in my...

Power Supply cover for Ender 3 V2 to place an 80mm Noctua fan.

This is a Designed Power Supply Fan Cover that mounts to the Creality Ender 3 (Original) 3D Printer Power Supply.This Cover's purpose serves to cover the power supply fan vent opening while silencing the noise from the power supply fan.

Smaller and more modern fan cover designed specifically to reduce noise on the Creality Ender 3 or Pro power supply. Hope you appreciate this addition! ... I've included two variations: in the first one, the fan cover points directly forward; in the...

Here's another easy to print and easy to install cover for the power supply of the Creality Ender 3 Pro enabling the installation of a ultra quiet fan. This is a 2nd generation remix of my original cover designed last year (10/1/2020) for the...

In my case, a buck converter isn't really necessary because the power supply already has a 12-volt output; however, I added one in so I can turn down the extremely quiet fan just a bit further. I uploaded my Fusion 360 files and STL files here for...

I upgraded to the second dual Z screw on my Ender 3 Max and needed to relocate the Power Supply so I made this bracket. Make sure you ground the power supply! Printing: Infill - 30%-100% (I like 100% for structural components) Supports - No ...

Print "Ender 3 Pro PSU Silencer v2.stl" for the Ender 3 Pro. v1 is closer to JGMaker Magic's. Mirrored versions are include for rotated hole patterns. Supports are only required for the mounting tabs. I adjust my support overhang angle to avoid...

... to 50 in Cura I believe).Be sure to only have one screw removed at a time. The fan will fall down into the power supply if both screws are removed.Mirrored alternative versions are included for some Ender 3 Pro models with a rotated hole pattern.

... in Cura I believe). Be sure to only have one screw removed at a time. The fan will fall down into the power supply if both screws are removed. Mirrored alternative versions are included for some Ender 3 Pro models with a rotated hole pattern.

The project for an Ender 3 motherboard case with screen and power supply to relocate the entire setup outside of a cabinet. Version 1.0 This case will be updated. Composed of four parts: - Motherboard base - Front and rear cases for the screen - Fan...

Quick Detachable PSU Mount for Ender 3 *The one in the photo had some modifications with power tools, all changes have been updated in the files. I wanted to be able to remove the PSU when I placed my Ender 3 in an enclosure, but also place it back...

Quick Detachable PSU Mount for Ender 3 *The one in the photo had some modifications with power tools, all changes have been updated in the files. I wanted to be able to remove the PSU when I placed my Ender 3 in an enclosure, but also place it back...

Quick Detachable PSU Mount for Ender 3 *The one in the photo had some modifications with power tools, all changes have been updated in the files. I wanted to be able to remove the PSU when I placed my Ender 3 in an enclosure, but also place it back...

... the screws provided: M5x8 and M5 T-nut. ...Gently pry open the enclosure by cutting a small portion with a knife if necessary, then carefully disconnect the support from the power connector. Remove part of the housing to access the power supply unit.

My power supply was getting pretty hot when printing PETG due to the High bed temperature so I decided to upgrade its fan. V2: Added holes so the air can flow out of the power supply. Fusion 360 file available Hardware: 8 - M4 x 16mm... ...The...

My power supply was getting pretty hot when printing PETG due to the High bed temperature so I decided to upgrade its fan. V2: Added holes so the air can flow out of the power supply. Fusion 360 file available Hardware: 8 - M4 x 16mm... ...The length...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament: ESun PLA+ Black Notes: Tree supports used on the end cap. ...You'll need 4x M3 Button Head Bolts Post-Printing ============= Fitted to...

Remix: https://www.thingiverse.com/thing:3530938 (Meanwell LRS-350 Casing) https://www.thingiverse.com/thing:4771030 (Mesh Design) Purpose: Mount a Noctua 92x14mm fan in Meanwell LRS-350 power supply Required NF-A9X14 Noctua Fan...

Remix: - https://www.thingiverse.com/thing:3530938 (Meanwell LRS-350 Casing) - https://www.thingiverse.com/thing:4771030 (Mesh Design) Purpose: - Mount a Noctua 92x14mm fan in Meanwell LRS-350 power supply Required - NF-A9X14 Noctua Fan...

* Remix: * https://www.thingiverse.com/thing:3530938 (Meanwell LRS-350 Casing) * https://www.thingiverse.com/thing:4771030 (Mesh Design) * Purpose: * Mount a Noctua 92x14mm fan in Meanwell LRS-350 power supply * Required * NF-A9X14 Noctua Fan...

This is a remix from the "Ender 3 Pro PSU Cover for 80mm" fans, where bigger is always better and I only had 120mm silent fans available. The cover has been adapted to have airflow channels at the top because hot air rises naturally. ... Fusion 360...

Ender 3 Pro source silencer, it is quite quiet and the airflow coming in is very good. They can print it with whatever layer height they want or at whatever speed they find most convenient. ... Print with brackets, it will just put the brackets in the...

I've added my logo and ham radio callsign to the vampyrex13 modified power supply silencer duct. The holes on this great fan duct are precisely the correct diameter for stock screws (2019 model PC fan screws). I'm thrilled with how it reduces noise...