ender 3 power supply upgrade 3d models

Super quiet Power Supply with 92mm 12V Fan Fan: ARCTIC F9 Silent - Extremely quiet 92 mm case fan, standard case design, almost silent, 0.08 sone, push or pull configuration possible, 1000 RPM...

After printing and installing this power supply mount https://www.thingiverse.com/thing:3154216 I found the movement of the power supply on the mount (due to the movement of the hot end and bed shaking the frame) was sufficient to cause intermittent...

After printing and installing this power supply mount https://www.thingiverse.com/thing:3154216 I found the movement of the power supply on the mount (due to the movement of the hot end and bed shaking the frame) was sufficient to cause intermittent...

its not really a remix but I took the fan silencer as a blueprint for it. ...Deleted inner structure. Works fine for Ender 3. For Ender 3 Pro you have to mirror it because the srews are directly on opposite sides.

... as a starting point. ...I removed the internal components and was able to make it work seamlessly for my Ender 3 printer. However, for those with an Ender 3 Pro, you'll need to flip the design since the screws are positioned on opposite sides.

its not really a remix but I took the fan silencer as a blueprint for it. ...Deleted inner structure. Works fine for Ender 3. For Ender 3 Pro you have to mirror it because the srews are directly on opposite sides. ... Category: 3D Printing

I went straight to OnShape.com and threw together a clip that slides down the extrusion channels and clips into one of the holes on the far side of the power supply. The fit is rather snug so there is no wiggle unless you purposefully try to move it....

This mount offsets the power supply a little to the side so you can use dual z lead screw mod (single stepper, belt driven) on your printer You will need: 2 x M4x16 screw 2 x M5x16 screw and M5 nut

I required a solution to redirect airflow and noise originating from the power supply. The print was straightforward, resulting in significantly reduced noise levels. ... I re-uploaded the file in proper format and created an alternative version...

INSTALLATION: - Remove only one screw from the power supply fan and use it to secure the printed part in place - Pivot the printed part to reach the second screw - Remove the second screw and reattach it with the printed part This way, the fan is...

... nobble's cover to make a fanless cover for the ultimate quiet PSU. ... I've seen similar designs for other PSUs, so decided to make one for the original Ender 3 PSU. ...I have been using this for over 3 months printing non stop, and no issues so far.

First, thanks to matthew798 for the design and for posting the f3d file along with it, I will also include the f3d of my remix. Changes I've made to the original. swapped sides for the power switch and hole for the wires Enlarged the hole for the...

Remixed nobble's cover to make a fanless cover for the ultimate quiet PSU.I've seen similar designs for other PSUs, so I decided to make one for the original Ender 3 PSU. ...I have been using this for over a year printing pretty often, and no issues so...

This print is compatible with: 'Tool Holder with integrated Slot Cover': https://www.thingiverse.com/thing:4071273 & the 14mm drawers from: 'Tool drawers for Creality Ender 3 PRO': https://www.thingiverse.com/thing:4657137 Please Like and Follow me...

When printed in good quality PLA, 0.12mm resolution, 100% infill, 4mm brim for adhesion (waiting for build plate to cool completely prior to removal), no supports, laying on the flat side, it ended up fitting perfectly on my Ender 3 V2. ...I love it.

Flipped the power switch location with the wire hole. 2. Expanded the wire hole to accommodate the connector snugly. 3. Extended the body and added countersunk screw holes so it can be securely attached to the PS. 4. Enlarged the mounting holes and...

Enlarged the hole for the wires enough so the connector will fit through 3. Lengthened the body and added countersunk screw holes so it can be attached to the PS. 4. Enlarged the mounting holes and countersunk the holes. ... Prints with no support, in...

This is a remix of OderWats WellFan Mean Well PSU Mod that's adapted for the standard Ender 3 PSU. Changes were made to fit the mounting holes and accommodate a larger, 92mm fan. I used a SUNON 92mm fan that's 24V and can be swapped easily without...

Remixed from https://www.thingiverse.com/thing:4568878. ... I added the Ender logo using FreeCad. I think it turned out great. ...Print time with my printer and settings was about 4 h and 15 min.

Hey, so I built it as the regular fan was shaking pretty badly, so I decided to upgrade to an 80mm quieter fan. Using the standard mounting screws, just flip the adapter around so it's facing outwards, then thread the wire through the existing hole...

Storage container equipped with two rail clamps securely attached to the top of the power source unit. For optimal stability, we recommend loading the storage container to at least half capacity, as the rear plate is a structural component that...

Main power is switched on with main power switch. LED strip switch controls lighting. ... Print settings for this project include: Printer: Prusa i3 Sunhokey Rafts: Disabled Supports: None Resolution: 0.3mm Infill density is 100% Notes: The...

I printed it with 3 top/btm/wall but zero infill, which means you can stop the print before or peel off the top layer, and I filled the void with some old sugar (2 years past use by, still works like a charm) to add mass to the body. Also included...

Power plug to Ender 3 Pro / Ender 3

The goal of this bracket is to move the power supply on the Ender 3 or Ender 3 Pro off of the Z axis frame and down onto the base of the printer. This is to reduce the weight on the Z frame in hopes of getting better acceleration performance and less...

This upgrade addresses a problem I encountered with the Prusa Lack enclosure's original part, which consistently pinched power supply cords. Inspired by the filament hole, I designed this modified piece for the bottom to guide power supply cords into...

I made the model to adapt it to ender 3 or pro. ... You'll have to cut 1cm from the chassis to better route the cables, then also on the power button.

Ender 10S Upgrade Power Supply Control Unit Stand Best Creality CR-10/S/V2 Upgrades & Mods elevates the control unit about 2.8 inch - 7.3 cm helps in good unit ventilation and better cooling easier access to the sd card avoid grounding electric...

This is a robust design for the Ender3 power supply mount, complete with a secure holder for the power cord. It's a remix of https://www.thingiverse.com/thing:3468297 The intention was to create something strong and easily printable. I've included a...

This clever solution frees up valuable real estate within the printer's workspace by relocating the power plug to its rear.