ender 3 pi camera 3d models

screw on camera mount for an ender 3. ...made in fusion 360.

Side-mounted pi case without the need of supports.

This is a mount for my Octoprint Raspberry Pi.

This case will hold a raspberry pi and a 12v to 5v convertor to power the raspberry pi.

None of the existing Raspberry Pi stations I found included accommodations for fans, proper airflow, camera cables, the USB port, either HDMI port or the audio jack. This design aims to address all of those issues. The base clips to the existing...

The BTT Pi TFT50 screen will need to be mounted upside down (yes that is correct) in the printed screen mount since its better to have the USB ports pointing to the left. 5. Slowly push the frame into the screen mount. Again this is a little tight...

Fan Mods I used: https://www.thingiverse.com/thing:4549738 https://www.thingiverse.com/thing:4548187 Camera Case I used: https://www.thingiverse.com/thing:2987719 I soldered the USB2.0 D+ and D- directly on the controller board, as well as on my...

There's also a small slit on the bottom of the case, I put that there to hopefully fit an SPI cable for the TFT35 SPI, I will use this case for that, https://www.thingiverse.com/thing:6478665USB Cable - This is what I will use to connect the PI to...

A back case for the Ender 3 Pro inspired by Teaching Tech's all in one case (https://www.thingiverse.com/thing:3688967). ...Designed from scratch using FreeCAD as a self learning exercise and to accommodate different components from the original.

In the need - I have designed and printed (and am using) camera holder for my Octo Pi setup on Ender 5 Pro. Four M3 screws are used (two to close the camera holder and two to mount holder to stand). Use one M4 T-nut with M4 screw to mount the holder...

This Raspberry Pi camera mount is specifically designed for the Ender 5 and an unofficial Raspberry Pi fish-eye camera. The bar of the mount fits perfectly into the V-slot rail between the two Z axis screw lead mounts. The model is designed to fit...

This Raspberry Pi camera mount is specifically designed for the Ender 5 and an unofficial Raspberry Pi fish-eye camera. The bar of the mount fits excactly in the V-slot rail between the two Z axis screw lead mounts. The model is made to fit an...

... and adds a touch of fun to your printing experience. So why wait? Upgrade your Ender 3 today with this simple yet powerful LED and OctoPi switch combination and discover a whole new world of possibilities for your 3D printing adventures.

mount it anywhere.... ...If you already have your pi in a case use mounting holes at back...

Tiroir de remplacement pour RaspBerry PI 4 et Ender3 V2 (pour mon cas) Prévoir ventilateur 5v 40/40/10

... -2 piece of M3 x 20-25mm screw and one M3 x 8mm screw + 3 M3 nut If you don't mind, please download it from my printables profile and leave a like if oyu liked it. https://www.printables.com/model/533433-ender-3-pro-raspberry-camera-front-holder

... the right side. For right side optional drawer see: https://www.thingiverse.com/thing:5138213 or https://www.thingiverse.com/thing:5138213 It's my first remix ever, so any suggestions are welcome. Printed and fitted on my Ender 3 V2 Neo.

The same as the original, the rear wall is thinned slightly and two of the mounting posts were shortened to fit the Pi zero 2w.

Remix of this to fit a Pi 5's slightly different IO. My modelling skills are weak, tolerances could be better, etc etc. ...But it works.

I required a mount for both my RPi3 and Camera simultaneously. Not finding anything suitable, I devised this solution myself. The result works exceptionally well for me. It was printed in a single, seamless piece. However, it necessitates careful...

I needed a mount for both my RPi3 and my Camera. Did not find anything sutable, so I came up with this. Works really great for me. Printed in one single peace. Need some careful handling to get the hinges released after it's been printed. ... Bolt on...

I work perfectly with my Wyze/Neos cameras. ...The camera base snaps securely into place without needing any additional tools or accessories - simply print and start using. ...I'm confident that everyone will love this design.

... versions of Ender 3 S1. ... Easy, screwless installation - simply slide on. Case for camera available here: https://www.thingiverse.com/thing:4227360 For Ender 3 V3 SE/KE https://cults3d.com/:1810674 For Ender 3 V1/Pro/V2 https://cults3d.com/:962475

Yet another Raspberry PI case, but this time only the base so you can use any heatsink you like. Works with all Raspberry PI 1-4b. ... It's a remix from https://www.thingiverse.com/thing:3256773 Needs support but can be very thin hope you like...

... unused. ...Works with most Raspberry Pi's, it fits my 3B and 2B anyway. Should fit the 4 too. All of the ports are still useable, and the SD card can still be taken out. The Pi slides in very easily, no screws or anything needed to keep it secure.

Inserting my pi into the remixed case left a lot of room below it, which can be used to accommodate connectors, cables, etc. but needs an isolator first to prevent short circuits. This plate fits below the pi. Can be just slid in, e.g. ...hot glue is...

Also added cutout for USB passthrough on front of the draw Pi runs at about 45c while printing (No heatsinks installed) Hole spacing for LM2596 used are 58mm x 32.5 Hardware required 8 piece M3x6mm (Pi and Converter can use 2 each if you haven't got...

The design itself is straightforward and doesn't actually provide any secure fastening for the pi, which isn't really necessary given its existing casing. ...However, it's worth noting that this dock won't accommodate a pi without some sort of case -...

Camera / phone mount for Ender 3 S1 pro, I used a Gopro clamp and an old phone

Logitech camera mount for Ender 3 PRO. ...Mount presses onto the Cover of the X axis stepper motor.