ender 3 pi camera mount 3d models
1081295 3d models found related to ender 3 pi camera mount.
thingiverse
A Pi camera arm mounted on the X-axis folds out of the way, securing itself with a stop inside to prevent excessive swinging motion. A picture is uploaded to display its design. Additional holes for screws are 2.85mm in diameter, allowing them to...
thingiverse
Remix und kleine Änderung des Halters. ... https://www.thingiverse.com/thing:3188580 Pi Camera ist bei mir von hinten am Drucker... ...
thingiverse
To set up: * Print the three parts of this mount, and the Pi case from the related post * Screw the arm onto the bed using the existing hex screw * Fix the Pi camera which is inside the casing to the post using the pin * Insert the post into the arm...
thingiverse
Simple shroud for the camera cover for ras434's excellent Ender 3 Pi Camera mount. I found with my light that I was getting too much light washout on the pi camera, so I made a quick and simple cover that simply pressure fits over the assembled...
thingiverse
Simple mount for a camera on the Ender 3. It fits over one of the V roller nuts on the right side of the X axis and is secured with an additional M5 nut. I designed it for the internals of an old webcam that I had, but it should also fit a Raspberry...
thingiverse
Slides on the front of the Ender 3 Y-axis and is compatible with cameras that use the 1/4 inch tripod mount. ...Make sure to check for clearance of the bed and camera.
thingiverse
Ender 3 camera mount, designed for the TP-Link Tapo C100 Security Camera. However it will work with other cameras with a little tweaking which is why I have uploaded the sketchup file also. This replaces the X motor cap. ...I would recommend going...
thingiverse
Ender-3 Raspberry Pi Zero W Mount: https://www.thingiverse.com/thing:3367387 Ender-3 Raspberry Pi Camera Mount: https://www.thingiverse.com/thing:3399648 .SLDPRT files uploaded for size change or tolerance adjustment. ... Installation:...
thingiverse
The plan is to install a standard USB camera on top of the construction plate by attaching it to the Ender 3's Y-axis clamp.
thingiverse
This is a modified version of RaffoSan's Ender 3 bed camera mount, now equipped with the GoPro-style connector from yyh1002's Modular Mounting System. The combination makes for an excellent time-lapse rig. To achieve optimal strength, print this...
prusaprinters
This is a remix of RaffoSan's Ender 3 bed camera mount https://www.thingiverse.com/thing:2999957 . It has the gopro style connenctor from yyh1002's Modular mounting system. ...Together this makes a great time lapse rig....
thingiverse
This is a custom webcam mount designed specifically for the C270 Logitech Webcam on the Ender 3 3D printer. It attaches directly to the Y-Axis Tensioner. Due to its structural importance, this mount should be printed with high infill density and 4-6...
thingiverse
I designed this in Tinkercad to specifically mount the Ring camera, but could be used to sit any camera of like size on top of the platform. It uses the frame screws next to where the SD card slot is to mount to the printer and M3 screws and nuts for...
thingiverse
This is a mount for a generic PTZ camera, or any camera with a standard 1/4" tripod screw mount. It bolts on to the front left leg of the printer using the existing screws. ...There's a hole punched through the piece to allow easy tightening of one of...
prusaprinters
Designed for an Ender 3 Will probably work on other printers too. ...Works with a Blink camerahttps://www.amazon.de/gp/product/B07X37DT9M/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
prusaprinters
Three components creating an azimuth-elevation mount for the camera. Connected via two short M3 screws (I used 5mm and 6mm). ...Nuts required.</p><p> </p><p>The view of the print is slightly obstructed by the print head but it gives a nice overview...
thingiverse
This is a bed mounted camera mount for a sony lifecam webcam. I installed this after I had a mount attached to the x-axis so that I can get better time lapses with octoprint. I also added points for zip-ties to hold the webcam cable. Also designed...
thingiverse
The swivel on the camera needs to be taken apart, and the weights must be detached after that it fits snugly in place. Print in ABS at 250 degrees Celsius with a 20-40% infill rate and a bed temperature of 108 degrees Celsius. ... The camera bolts...
thingiverse
I wanted an extruder mount that used the screws to attach for a stronger and more rigid part. ...I saw one like that in a YouTube video, but I could never find the model, so I made my own.It needs a new x-endstop switch piece so that you can use the...
thingiverse
Raspberry PI Camera standard to screw onto the base of the Ender 3
thingiverse
Baseplate attachment for a Tenlog D3 pro to attach the "Ender 3 Raspberry Pi Camera Mount" thing. https://www.thingiverse.com/thing:3188580 I used nylon standoffs on the 30mm spaced holes on the E2 home sensor cover, then attached this baseplate...
thingiverse
Bracket simplifies mounting on Ender 3 with ease. ...Attach velcro to a flat surface, and it will provide a secure mount. For the Pi case and foot source, visit https://www.myminifactory.com/object/3d-print-raspberry-pi-camera-v2-mount-80897
thingiverse
I remixed the Ender-3 LCD Pi casing by dennisheijmans (https://www.thingiverse.com/thing:3891349) to add Camera support and cable camera passthrough
thingiverse
Raspberry Pi 2/3 mount for Ender 3 printers. The case is designed to be mounted on the left side of the frame of the printer. To mount simply unscrew the two front screws holding the mainboard case and align the holes of the mount with the screws.
thingiverse
A 3 stand designed for the rasberry pi camera that attaches to the ender 3, No supports needed, Used meccano screws
thingiverse
The original Pi Camera mount from the website (octoprint) does not fit the bracket on the Ender 3 Pro. I made the slot wider (2.5 mil instead of 2) and added Two (2) slots to the bending arm. These slots serve a purpose and allow the user to install...