ender 3 part cooling fan upgrade 3d models

This is a specially designed dual-part mounting system for a 50x15 radial fan, engineered to significantly enhance part cooling efficiency on the Anycubic Kossel 3D printer.

In contrast, the fan mount from thingiverse.com/thing:15899 only decreased heated platform temperature by 3 degrees C and allowed for well-printed parts. This part completely replaces the wood piece in Printrbot, with screws being reused. The...

Upgraded the failing fan to this part and installed a robust 40mm server cooler, resulting in a significant boost of airflow now.

... fan. ...Dragon hotend and HextrudORT. It works, but I think I can tweak the angle a little bit. Uses a 40mm fan Designed a part cooling fan that is fastened in the HD12 hextrudort carriage. ... (I use it in my HD9 mod of the HD12 carriage)

E3d Part cooling with single or dual radial fan. Mounting bracket to the back of the E3d chimera. ... Category: 3D Printer Extruders

E3d Part cooling with single or dual radial fan. ...Mounting bracket to the back of the E3d chimera.</p> Category: 3D Printer Extruders

I appreciated [Horvat208's](https://www.thingiverse.com/thing:4153402) 4020 hot end fan shroud as well as [mrfochs'](https://www.thingiverse.com/thing:2972610) adapter to use 40mm fans for part cooling. I could have simply used them straight up,...

I liked Horvat208's (https://www.thingiverse.com/thing:4153402) 4020 hot end fan shroud, as well as mrfochs' (https://www.thingiverse.com/thing:2972610) adapter to use 40mm fans for part cooling. I could have just used them straight up, but didn't...

Please note : will only fit the Ender 3 v2 Neo and not the original v2 as they changed the hotend mounting plate! Huge thanks to the original designer for the effort recreating the stock shroud connectors! I found the shape a bit too wobbly so...

This Rev2 version has a beefier fan mounting arm designed to prevent it from snapping off like the original.\nThis high-efficiency fan duct upgrade is specifically made for the stock part cooling fan on a Rigidbot 2 printer, and attaches using all...

This is a high efficiency fan duct upgrade for the stock part cooling fan on a Rigidbot 2. This fan duct attaches using all stock parts so no modifications or extra parts are required to install it on a Rigidbot 2 printer. For best results read...

I made this dodgy part cooling fan to be compatible with this E3D mount for the Ender 5 -https://www.thingiverse.com/thing:3682669 because I like the lightweight construction. While it is very much not a finished design it works and did okay in my...

Part cooling fan for the Creality CR6 SE that uses the stock blower flan but directs the airflow closer to the nozzle. ... Version for 40mm quiet fans: https://www.thingiverse.com/thing:4777287

The Tevo Little Monster comes with a pair of awesome 4010 fans for part cooling, but most of that cooling is wasted by only blowing air in the general area of the part.These fan ducts require no modifications to the sheet metal bracket, simply print...

The stock cooling fans on these machines are simply not up to par when it comes to handling decent overhangs or faster printing speeds. A double 5015 upgrade will more than meet the cooling demands of this machine. I run them at around 50% and find...

... cooling on all sides of the a part that I am designing so I needed something that could handle that. *Note* I used the mounting system of the E3D Hemera front-side 5015 part cooling fan mount (semi-usable) part but designed the rest on my own.

Bend the tube carefully using a 22AWG wire inserted to prevent kinking. The 30mm fan shroud has to be placed in the angle as shown in the picture to clear the arms and the whip connector, it's a very tight fit! Fan 0 on the Rambo Mini works as a part...

After searching for a replacement, I discovered a 3D model of an Anet ET4 part cooling fan designed by dukuby, but it wasn't compatible with my printer. ...To solve this issue, I made some modifications to the design to ensure it fit perfectly on my...

Folks, when assembling our FSuns Q Crickets cooling fan, make sure to seal that gap between the fan and the vent pointing towards your printed part. If there's even a small hole in any of the air ducts, you'll lose precious airflow needed to cool...

... heat sink cooling for stock hotend of the raise3d n2 series. ...Designed for a noctua 40x10mm 12v fan. https://www.amazon.com/Noctua-Cooling-Blades-Bearing-NF-A4x10/dp/B009NQLT0M/ref=sr_1_3?dchild=1&keywords=noctua+40mm+fan+12v&qid=1631122389&sr=8-3

This modification is designed for the Prusa MK3 with the 45-degree factory-recommended part cooling upgrade, specifically created to address the limitations of the basic part cooling duct on this model. Please note that this upgrade is not compatible...

I made ??a duct parts for mounting the cooling fan work by fixing the heat head base portion. It becomes the part you have a sufficient air volume and exquisite clearance to prevent interference with the fixed bed clip. Take a large opening, Ver01 is...

micromake part cooling fan for long hotends Print with brims No rafts required 0.2 mm layer 40-60 mm/s 10-15 % infill Category: 3D Printer Parts

To ensure efficient cooling, the fan is securely attached to the hotend carriage next to the existing hotend cooling fan using a sturdy fastener. The duct itself fits snugly onto the shoulders to prevent any accidental over-insertion. This upgraded...

• Use two M3x6 screws for radial part fan • Use four M3x12 screws for hot end fan Radial fan is available on Amazon: https://www.amazon.com/gp/product/B07RR2KGN9/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Screws are available from Amazon:...

Raised the fan connecting end to improve airflow. Expanded the circle and moved it closer to the base for better balance. Centered the nozzle for optimal performance. Tested the design and fine-tuned the airflow to perfection. For those who want a...

This is my final shot at designing a part cooling fan mount for your DyzEnd hot end. It's a Heat Sink Mount that utilizes a 25mm brushless fan to minimize weight, and it performs fantastically! I recommend printing another one immediately after...

Alternative part cooling fan duct for the Anycubic Mega X.Fits 50 x 50 x 15mm radial fan 5015.Only needs support under the radial fan mount.Printed with 0.4mm nozzle at 0.2mm layer hight. ...Used Bavaria Filament V19 (~ASA).</p>

Took the original Prusa i3mk3s+ part cooling fan mount and made a better one for Phaetus Dragonfly hotend, now the air will not blow on the silicone sock, but will actually cool the part. ...It's just a little bit higher.

Took the original Prusa i3mk3s+ part cooling fan mount and made a better one for Phaetus Dragonfly hotend, now the air will not blow on the silicone sock, but will actually cool the part. ...It's just a little bit higher.