ender 3 part cooling fan upgrade 3d models

I upgraded my Ender 3 with the TH3D dual extruder board. The board is available for purchase on https://www.th3dstudio.com/product/creality-cr-10-and-cr-10s-dual-extruder-upgrade-board/. I sourced a 2 into 1 hotend from eBay, located at...

The best solution would be to upgrade to a 5015 blower, but in an effort to quiet my ender 3, I bought a package of dual ball bearing 4010 fans. I tested this setup in place of the stock ender 3 part cooling blower with the Petsfang Bulleye. I was...

With Prusa slicer, the overhanging test can go to 65~75 degrees (PETG, 100%fan after layer two, Auto cooling is on) (might not as good as other single 5015 blower mod, but good enough for me while having other benefits and cuteness~)...

The fan dock fits a 4020 blower fan (24V to fit the ender 3 stock or v4.2.7 board) with half of its case removed. ...(Aliexpress link) The fan exhaust is not tuned to perfection and works best without the silicon sock installed on the heat block.This...

New upgraded fan housing with circular duct for stock CR10 4020 part cooling fan.

( Zuff's & Hero Me Gen7 https://www.thingiverse.com/thing:5747259) ( PrusaSlicer 0.2mm NORMAL setting, PETG 220/90, turn the fan 100% on after layer two) (The testing stl is from here. https://www.thingiverse.com/thing:2151369) Thanks to Josue...

I wanted to get close to the print head but only put air on the part, not the nozzle.For that purpose I used the nozzle portion of the following air duct that was made for the stock fan (https://www.thingiverse.com/thing:3255518). The channel in...

I wanted to get close to the print head but only put air on the part, not the nozzle.For that purpose I used the nozzle portion of the following air duct that was made for the stock fan (https://www.thingiverse.com/thing:3255518). The channel in...

This is a 'Ender 3 v2 NEO Hotend Cooling Shroud for 4015 fan cover'

Habe eine kleine Schublade am Ender 3 gebraucht und diese entworfen. Es ist ein kleines aber feines Upgrade wie ich finde. Viel Spaß Used a small drawer at Ender 3 and designed this. It's a small but nice upgrade in my opinion. ... Have fun

Part Cooling Fan Duct upgrade for the TronXY P802MA printer Category: 3D Printer Parts

The stock cooling duct on my Ender 3 V2 did not cool the back of the part well. I designed this to help improve that. I wanted to keep the stock parts and look. I added two flow straighteners. From my experience, the blower fan pushes all the air to...

Suitable for Ender 3 and Ender 3 Pro. ... Modification air cooling flow referring to Ender 3 V2 air flow style. -Need Support. ... -Best using PLA filament

Upgrade Your Bobine for Smooth Rotation and Zero Friction Ensure Perfect Performance on Creality Ender 3 and Ender 3 Pro Models Before Upgrading, Consider the Following Essential Components: - Two precision bearings with an outer diameter of 22 mm...

Slim hotend cooling duct for one 4010 axial fan (cooling Hotend) and two 4010 radial fan (cooling component) something like this https://www.amazon.de/gp/product/B08H5D6D1X/ Ender 2: 12V Ender 3: 24V? ...

CFD optimized part and heatsink cooling system with LED for original Mosquito hotend as well as clones for Ender 3/Pro. ... Print settings: * TBD Parts: * TBD Check out my other designs: https://www.thingiverse.com/DaVinci2000/designs

I no longer have the V2 Neo, but these were the last changes I made to these shrouds which gave me the best look/fitment.

... cooling fan air duct. Authored by our Staff Writer Johann Wyss, and published in our magazine Issue 26, September 2019. The full article can be accessed here: https://diyodemag.com/education/exploring_3d_part_3_beginners_guide_to_fusion_360

The part cooling fan is connected directly to the motherboard's K_fan connector; double-check polarity when making the connection. With this cooling configuration, there will be no backflow from the hotend fan towards the print, resulting in...

This is a minor tweak to the fan holder created by James Tongue for his fan duct. It was used to install the E3D Hemera Direct Kit. My alteration involves an enlarged mount and washers to fit the screws supplied by E3D. ...You can access my mounting...

This is a small adjustment to the fan holder designed by James Tongue (https://www.thingiverse.com/Hangtight/about) for his fan duct (https://www.thingiverse.com/thing:4042492). This was used to mount the E3D Hemera Direct Kit. My modification...

upgrade spool holder ender 3 use rolling x4 print: 0.2 infil : 25% thickness: 1.2 no support...

I recommend using washers with the two screws securing the fan duct to the aluminium MicroSwiss plate. . . The XY-Offsets can be adjusted to fit this design sending the following commands followed by an M500: . . ... V4.0: BLTouch: M851 X-44,87...

This is a new reworked version of my original CR10/Ender3 MicroSwiss DirectDrive Fanduct: https://www.thingiverse.com/thing:4277669 . . . The new versions have a few key differences to my first approach: . . V4.0: (DISCONTINUED) -Modular design to...

I'm Ben Levi, and this is "BLV Ender 3 Pro - Upgrade," an open-source project that I'm excited to share with you. Designed specifically for the Ender 3 Pro 3D printer, my goal is to take this popular machine to new heights of performance and print...

... fans or guard, so I came up with this design. It features internal support/air diverted to eliminate the need for external supports. I hope you all like this cooling ring - my Ender 3 Pro now prints with near zero stringing and bridges like a pro.

I imported it, selected the duct part, moved it down 8.5mm, uploaded it hereexactly the same as the original but the duct now extends 8.5mm longer to reach volcano nozzleIf you use certain direct drive plates this might be too tall

upgrade spool holder ender 3 use rolling x4 print: 0.2 infiltration: 25%. ... thickness: 1.2 no support ...

... duct with ease. Written by our Staff Writer Johann Wyss, this tutorial is featured in our magazine Issue 26, September 2019. The full article can be accessed here: https://diyodemag.com/education/exploring_3d_part_3_beginners_guide_to_fusion_360

CFD optimized part and heatsink cooling system with LED for original Mosquito hotend as well as clones for Ender 3/Pro. ...Print settings: TBD Parts: TBD Check out my other designs: https://www.thingiverse.com/DaVinci2000/designs Category: 3D Printer...