ender 3 part cooling fan duct 3d models

E3D Hemera fan duct to use a airpump instead of a fan.I use a piece of 6mm aluminum tube to connect the hose to.I´ve also uploaded another version which uses two 3mm tubes instead of a printed duct, which gives you the option to find the best flow...

... fan duct design is suitable for the stock hot-end and others of a similar size. However, I created an alternative volcano fan duct design specifically for hot-ends that hang lower than the stock model - perfect for E3D's Volcano hot-end setup.

When installing a *Phaetus Dragonfly BMS* on my *Tronxy X5SA* I've encountered the issue that my old [fan duct](https://www.thingiverse.com/thing:4849688) is now some mm to low compared to the new nozzle Z position. So I remixed my [fan...

Redesigned, LOW PROFILE Ender 3 Pro Nozzle Cooling fan Duct

Fan Duct for Sovol SV01. Layer height: 0.12mm Manual Support - Bridging is Possible, No Support Inside; Only Fan Inlet! Fits Perfectly to My Sovol Printer. Edit 27.01.20: I've Made Major Changes to the Air Duct, Making It Larger and Significantly...

... by other parts out there that don't fit my printer exactly. ... The duct sits comfortably around the extruder, with a around 1mm gap above and 1mm distance from the tip of the extruder. ...Does not seem to be affected by the heat at the given distance.

A part cooling fan for NF Sunrise extruder using a V6 block, it should be easy to convert for use with a Volcano. I haven't got my bridging settings dialled in so I've added models with internal supports which may or may not work for you. There's...

Remastered this exceptional duct to suit my requirements and customized it to fit perfectly on my carriage shroud. ...Thanks a million, Locki!

Remix to change bracket and accepts ender 3v2 laser holder: https://www.thingiverse.com/thing:4643629

... a Dragonfly extruder that is not as long as the stock hotend on the SV01/SV03. ... Update: the small size results in very poor air flow. Instead, use either the original or my BL Touch remix of the fan housing to allow for using a regular fan shroud.

Ender 3 Extruder brushless cooling fan blade, 拿走不谢!!!

This system allows a 40mm blower fan to be perfectly fitted onto the Tronxy X3 FDM printer. Its design leverages the identical mounting holes found on the hot end shroud, providing a seamless integration. To secure it in place, simply use short...

... the nozzle tip to help it print. Mirror image it so it can be used on the right extruder. SO as to avoid it contacted the fan blades. It fits both F430 and F160. You may wish to scale / stretch it a little to aim the air a bit lower. ...

... awesome time saving lib sc.scad. Print instructionsCategory: 3D Printer Parts Summary Simple little fanduct for use with 8mm M3 screws, prints without supports. ... Also, thanks to Rudolf Huttary for writing this awesome time saving lib sc.scad.

Simple little fanduct for use with 8mm M3 screws, prints without supports. Also, thanks to Rudolf Huttary for writing this awesome time saving lib sc.scad. Print instructionsCategory: 3D Printer Parts Summary Simple little fanduct for use with 8mm M3...

Fan Duct for Ender 3 - A First-Time Success My inaugural venture into creating a fan duct for this popular 3D printer has yielded impressive results. After printing and putting it through its paces, I'm pleased to report that it's working seamlessly....

Additionally to that you need the following parts - Mistral-E Filament Cooling Duct [https://www.thingiverse.com/thing:3255518](https://www.thingiverse.com/thing:3255518) - 4x M4 screws (length depending on what kind of fan you mount) If you want to...

Fan Duct Ender 3 S1

... Always willing to take suggestions and will likely tweak the design here and there to improve performance. You can reuse the M2 bolts that come on the stock Ender fans, but you will need an M4 bolt and threaded insert to attach the fan to the duct.

https://www.thingiverse.com/thing:2350437 Because I also installed jneilliii's "Radial Fan Fang for Creality CR-10" on my Ender 2, I discovered that mounting all the gear to the x-carriage only with the two M3 screws holding the hotend was a bit...

https://www.thingiverse.com/thing:2350437 Because i also installed the "Radial Fan Fang for Creality CR-10 by jneilliii" https://www.thingiverse.com/thing:2237084 on my Ender 2, i found that mounting all that gear to the x-carriage only with the two...

This is a high airflow cooling duct for the Ender 3/3 PRO and CR-10 This design enables conversion from bowden tube to direct drive link to buy the 2 blower fans:...

This lid is designed specifically for Razer35's remix of the 3D Cooling Fan Duct, available at https://www.thingiverse.com/thing:2334407. I'm a huge fan of that mod and have successfully modified my fan to K-FAN in the board, giving me control over...

I then made another version with cooling capability around the entire nozzle using a full circle air duct. I had some issues with the fan bracket being perpendicular to the nozzle, so I made four versions (0Deg, 2.5Deg, 5Deg, and 7.5Deg) where the...

The Ender 3 features a dual fan cooling system, carefully designed to minimize interference with its mechanical components. ...The aim was to streamline airflow while keeping the additional fan in sync with the original unit's performance, requiring...

Remix for Ender 3 stock part cooling fan with creality spider hotend Version: * Ender3_Spider_FanDuct = default * Ender3_Spider_FanDuct_6mm = more space between hotend and duct * Ender3_Spider_FanDuct_Short = short version

Recently, I stumbled upon this really cool project: https://www.thingiverse.com/thing:2076964. The original design had one major flaw - the mount on the X-axis was way too long. To fix this issue, I simply removed the mount and voila! The entire...

... Mounting System Makes Installation a Breeze, Allowing You to Focus on Perfecting Your Prints. Say Goodbye to Delays and Hello to Smooth, High-Quality Prints with the Ender 3 Cooling Fan Nozzle Kit. ...Upgrade Your 3D Printing Experience Today!

Slim hotend cooling duct for one 4010 axial fan (cooling Hotend) and two 4010 radial fan (cooling component) something like this https://www.amazon.de/gp/product/B08H5D6D1X/ Ender 2: 12V Ender 3: 24V? ...

I tried using the original design on my Ender 5+, but unfortunately, the tabs for the screws were slightly too thick. Printing it with resin proved to be a challenge as well - the logo required extensive support structures, which made the process...