ender 3 octoprint 3d models

I'm using the Octoprint-Enclosure plug in to trigger some GCODE for each button. As buttons, I used some generic 24mm "arcade buttons" found on amazon. I use the top 6 buttons to perform routine actions, homing, set temperatures, filament...

This is a 3-part case designed to mount a Raspberry Pi 3B+ to a Creality Ender 3 using M3 machine screws and t-nuts. Mounting points in the center part allow for the installation of a small 5V fan for cooling the pi during use. This fan may be...

In addition to the camera mount, the package also includes a Wifi antenna mount that fits into the Enders case cover hole originally intended for the Z endstop cable. A small component, referred to as C6, is included to prevent the camera cable from...

... the driver bouard is HX711. These STL is what I made for my 3D printing cabinet. The spool holder is from my Creality Ender 3 Pro, but I use it for my Prusa as well. ... Info on the plugin: https://plugins.octoprint.org/plugins/filament_scale/

Add **custom shortcut buttons** to your Ender 3 using Octoprint and the [Physical Button Plugin](https://plugins.octoprint.org/plugins/physicalbutton/)! Now you can simply heat your hotend or bed with just one click. I've assigned the buttons to...

I've remade this to fit the Ender 3 Max as it is made differently and the original one just doesn't fit it. This is made to slot into the 4020 section ad located behind the installed LCD screen. ...and hole for 40mm fan is in the side to allow air...

This mount clips onto the rail of an Ender 3 (or any other device using the same extruded rails as an Ender 3). The head is designed to accommodate a Logitech 270-class camera (any Logitech with that unusual folding clip attachment). The gooseneck...

** BEWARE THE STL HAS SOME PROBLEMS ** ** AS 2009-04-10 I'm still trying to fix the mesh ** AiO setup with a RPi 3 Model A+ Modified the base to add support for the A+, will change the front STL next Building Instructions Follow the original from...

**CAUTION: THE STL HAS SOME ISSUES** **AS OF APRIL 10, 2009, I AM STILL TRYING TO RESOLVE THE MESH PROBLEMS** AiO setup with a RPi 3 Model A+ ========================== Modified the base to accommodate the A+, will modify the front STL soon Building...

English A case for the Raspberry Pi to get the most out of Octoprint, with short cable runs this case adapts perfectly to the Ender 3 v2, as if it was already designed that way at purchase. </p> <p>The 24V power supply line can be laid directly in...

There are so many Raspberry Pi cases out there for various combinations of Ender 3 and Raspberry Pi. However, I couldn't find one I liked for the Pi4b and the Ender 3 v2. So I made one! ... Original inspiration was this:...

I didn't find a picam mount I liked so I designed one that fits snugly over the Ender 3 y-axis tensioner bolts without requiring disassembly. The field of view is most of the print bed until the y-axis is fully extended, and it clears the axis at...

... * Configure OctoPrint UI to access relay controls using the following code: ```yaml system: actions: - action: pon command: printer_on.sh name: PrinterOn - action: poff command: printer_off.sh confirm: Are you sure you want to turn off the printer?

Remix of https://www.thingiverse.com/thing:4838281 for use with Raspberry Pi 3/3+ Models. Please download the latest V2 version if you have already downloaded the original before printing. V2 corrects the error of incorrect ethernet/usb port...

... this box from Scott Yu-jan. ...I really liked his video's but I used a raspberry pi 3. His model was made for the raspberry pi 4. But its really clever to put some buck converters in there. ...So i replaced the part where the raspberry pi 4 is placed.

Remix from https://www.thingiverse.com/thing:4648289. I remove the switch hole and the grill and add a new grill for a 30mm fan (https://www.thingiverse.com/thing:2802474), what is connected to the RPI GPIO. ...Also I modify the LM2596 holders...

The rear IO on a Raspberry Pi 3 gets turned upside down when compared to a Raspberry Pi 4. ...This redesign relocates the Ethernet jack and collection of USB connectors to suit the needs of a Raspberry Pi 4.

Remixed from giacomo30196's wonderful [Ender 3 Octoprint Set Up](https://www.thingiverse.com/thing:3063845) box. This version will fit an Ender 3 Pro and hold larger FC-65 high-amp relays and larger LM2596 voltage regulators with LCD displays, in...

Remixed from giacomo30196's wonderful Ender 3 Octoprint Set Up (https://www.thingiverse.com/thing:3063845) box. This version will fit an Ender 3 Pro and hold larger FC-65 high-amp relays and larger LM2596 voltage regulator with LCD display, in...

I remixed the original design found at https://www.thingiverse.com/thing:3063845, replacing the base with two high-voltage relays recommended in the original source:...

Remade the entire design to accommodate a Raspberry Pi 4 and two buck converters, which significantly boosts performance. Additionally, I removed the logo from the cover for a sleeker appearance. ... This build is optimized for a 30mm fan, and I managed...

Added a standoff for an IRF520 Mosfet in hopes of GPIO Controlling/Dimming LED lighting on Ender 3 V2. ...Will update once printed

I wanted a cut-down version of this to handle moving the control panel of my Ender 3 so it could accommodate an Octodash in place of the Creality screen. Nothing fancy, just threw it into Tinkercad and cut the corner out. ... Used in conjunction with...

... und mit dem Slicer in die Öffnungen des Deckels gemacht. ... Die Cam-Halterung habe ich von https://www.thingiverse.com/thing:3147295 Unter https://technikmensch.de/octoprint/ habe ich eine super Anleitung gefunden. ...

&nbsp;The cover portion fits nicely within the frame and can be removed whenever you want to.This is a remix of “Octoprint Monitor Single Station Front Cover” by Bazzelworks found at this link Octoprint Monitor Single Station Front Cover by...

Just a simple clip on case for the Ender 3 X gantry to house my Octoprint Monitor. I just wanted a quick way to check on my print status without needing to approach the printer to open the LCD cover I have on it & kept misplacing the Octoprint...

Check the Thingiverse page here to see previous makes and remixes.&nbsp;SEE ALSO:Universal Buttonbox (for example for enclosures or other printers)&nbsp;Ender-3 ButtonBox (for OctoPrint)This is for the people who prefer to use Ctrl+S over jumping...

# Ender-3 ButtonBox (for OctoPrint) # This is for people who prefer to use Ctrl+S over jumping into menus to save something. On my Ender-3, I got tired of scrolling through the LCD menu to use basic functions like homing all axes, preheating for PLA...

This is a comprehensive enclosure designed specifically for users running Octoprint on their Ender 3 or Ender 3 Pro. The enclosure is an integrated solution that combines elegance and simplicity, making it perfect for those seeking a hassle-free...

... like the following tutorial (I still use a Raspberry Pi). https://www.youtube.com/watch?v=74xdib_-X38 Print Settings Printer brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 20% Filament material: PLA