ender 3 octopi case 3d models

I designed this case for the Raspberry Pi 4 B to mount to an Ender 5. It connects to the back 2020 rail using T nuts, and has an arm to use the Raspberry Pi camera (V1 or V2). I've included mounts for LED lights (link below) and included pictures...

This is a basic octopi station that goes under your display module and can store your raspberry pi (either model 3 or 4)

I've colour matched my LED to the one that's included in the Ender 3 V2 Neo CR touch to make it extra snazzy, Just screw mount the Raspberry Pi to the drawer base. I used recessed M2.5 screws that screw into a heat-sink from the bottom up. Then it's...

I didn't like any of the solutions I found for mounting an OctoPi on an Ender 3-V2, so I spent a preposterous amount of time creating one. I don't think the storage drawer is very useful, so I designed it to use that space, and to also house a couple...

The tool-drawer holder in the Ender 3 v2 is the perfect place to put a Raspberry Pi running OctoPrint’s OctoPi (big shout outs to Gina Häußge and Guy Sheffer). Just screw the RasPi on the frame, plug in the connectors and slide it into the printer....

I was looking for a way to get my printer more organized and decided that I would mount the Raspberry Pi Eviciv touchscreen I use for OctoPi on the Ender top bar. The top bar is 20mm and this mount has a few features to make it easy to remove. ...

This is an easy-to-print storage tray for an Octopi - tested to fit a Raspberry Pi Model 3b. ...No support should be necessary printing from the face down.

These are two models that I reworked for the Ender 3 Max and added a spot for a 4010 fan for active cooling. ... The BTT is reworked for a BBT E3 V3 screen and a Pi4

Here is rewritten text: The Ender 3 Pro 2 release is paired with a Raspberry Pi 3B model, while the DC-to-DC power supply uses an LM2596 module. ...The relay is provided by HiLetgo.

This is a Camera Arm for the Ender 3 v2 Printer. I am pretty sure it works on other printers, but if it doesn't, lmk in comments, and I will make a version for them! Have a great day! ... copyright Ben Walker

I was searching for the perfect OctoPrint setup for my Ender 3 Pro printer, but everything I found had one major flaw - they didn't address the issue of securing the unit to the Y-axis. ...Determined to find a solution, I dove into remixing and...

I know others are out there, but most take too much room on the bottom rail, and then you cant mount any of the cool Ender 3 drawers. This one allows space for the drawer to the left of the LCD. I printed in PLA+, need supports, just print upright. ...

This is my left side mounted holder for the ender 3 v3 SE.For the camera mount i looked at this design ( https://www.thingiverse.com/thing:3700643 ).For Dc buck converter i used :(...

I Mixed this design from "Closed Support for LCD ender 3" by DaniBicho, adding space to install a raspberry pi 3 and a cooling fan. I also added a bottom layer to accommodate a buck converter. To keep things tidy, I included a spot for the usb cable...

The case is somewhat modular, making it possible to fit either a Pi 3 or Pi 4 by printing the corresponding front plate. There are two tops available – one with and one without a GPIO cutout. Three bottoms are also available: one with no mounting...

New Version for 5-Amp Relay: https://www.thingiverse.com/thing:3422338 Octopi Case with Two-Channel Solid State Relay for Power Supply Control, Raspberry Pi 3 Included, Cable Grommet Included. Assembled with 2.5 x 10 mm Screws. ... Two-Channel Omron...

After searching for a suitable case to house an Octopi setup with extra space for a relay board, I was unable to find one that met my needs. As a result, I designed my own case, which accommodates a Raspberry-Pi 3, a self-made relay card, and...

Designed this Raspberry Pi 3b case to protect the circuitry.  Printed this and use it every day to run my Ender 3 Pro.  The case has saved the Pi a few times from stuff falling on it.  I used some small countersunk sheet metal screws to fasten the...

A small case I designed in OnShape for my Raspberry Pi 3 B+ OctoPrint server. ... Gives good protection to the circuit board with ample access to the SD card slot and all ports, plus some ventilation to prevent overheating.

... excited to show you my Raspberry Pi case for OctoPrint! ...To be honest, the lid doesn't print perfectly as it has recessed edges that fit snugly into the case and can't lie flat due to the OctoVoronoi design on top. ...However, I think it looks great!

Frustrated by the chaos of tangled wires and multiple boards, I set out to create my own custom case that would integrate it all plus a cooling fan to chill stepper drivers! To empower others to tailor this design to their specific needs, I've...

Remix of https://www.thingiverse.com/thing:4838281 for use with Raspberry Pi 3/3+ Models. Please download the latest V2 version if you have already downloaded the original before printing. V2 corrects the error of incorrect ethernet/usb port...

This maker is created from the excellent "Ender 3 LCD Cover Octopi Station" by jlmpenedo, with an added feature for mounting a Logitech QuickCam for Notebook Pro. ... My very first remix!

Quick remix of several ender 3 S1 side mounts and an octoprint Pi case.

2) Added v2 heavier duty case clamps This is a remix of Frank (Tronnic) Klötzer's Ender 3 Touchscreen Case & Holder for Raspberry Pi. I really like his design, but wanted a few changes for my CR-6 SE: 1) Wider mount plate to help hide cables 2)...

This is a Remix of the [Ender 3 v2 Hidden OctoPi Mount](https://www.thingiverse.com/thing:5201485), by [Department_Nine](https://www.thingiverse.com/department_nine/designs). For more varity have a look at the Original. ... I Realy liked the Original...

...On an Ender-5, try rotating the X-axis stepper 180 degrees and run the cables up from the front rather than from the back of the frame. The Pi case sits tucked away above the control panel, and the cables will naturally roll up to the x-Axis gantry.

This is a remix from https://www.thingiverse.com/thing:398515 needed a clip to deal with the usb cable on my ender 3 from my octoprint

This is a rack for hosting raspberry pi 4 installed with Octoprint as well as the camera holder.The pi rack is open designed to allow max air flow.For camera holder you will need to print number of arms large/medium/small to suite your need.At least...

Installation ===== * loose the right corner screws in the base of Ender 3 S1 pro, push the my mount print into and then put screws back * after that the pi case can be installed to the left with the dove tail joint * cam holder is easy as seen in...