ender 3 neo z offset 3d models

Customized version of https://www.thingiverse.com/thing:3267568 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3267568 hope this helps if its to tight you can make it longer

... it online https://www.tinkercad.com/things/5OBkzZ8BsEF 1. Remove the original cowl. 2. Fix the duct to the stock fan mount with three of the original screws. 3. Super glue in the 5015. 4. Figure out how to mount your hot end fan. ...

A small spacer can be screwed onto the Ender 5's spacer screw if switching to a thicker glass build plate is desired. To prevent losing this small item, I added a tab to hang it on the screw when not in use. It should be customizable, but...

MINI-Z RIM AERO V4 +3 OFFSET

bit better z offset and cable routing more room for the stepper ONLY for the ender 3/pro its very rough i did it on tinkercad

ender 3 v2 NEO direct drive bracket

This adapter adds a 3.5mm offset to the Z-axis of your Tevo Tornado, which is crucial when installing a glass bed on top of an existing heated setup. The original component was too bulky for my older tornado with the red heat bed sticker, so I had to...

... 3 max Neo. This is simply stretched a bit more to fit past the z axis block. I also slightly enlarged the opening for the smaller wrench to accommodate the wrench that came with the Ender 3 Max neo, it must be slightly larger than the original.

proste i funkcjonalne do ender 3 v2 neo, nie mogłem znaleźć odpowiedniego, więc udało mi się stworzyć, chociaż zaczynam dopiero zabawę z drukiem 3d

Same thing, adapted for Ender 3 v2 Neo.

It's a roller guide for Creality Ender 3 Neo

holder for the ender 3 v2 neo tools

Minimal scraper holder for Creality Ender 3 V2 Neo.

3D Printer Creality Ender 3 Neo Carriage Plate

Z carrier from ender 3

JUST AN ENDER 3 V2 NEO LED LIGHT FIXTURE OpenSCAD source code also available.

This is meant to replace the knob on the Ender 3 v2 Neo's LCD screen.

Ender 3 Max Neo printable tower supports and printable attachment hardware.

Bras guide filialement pour la ender 3 v2 neo avec ou sans sigle. ...

This is just a basic drawer for the Creality Ender 3 Neo 3D printer i made.

Basic model of tools holder for Ender 3 v2 neo. ...Good fit, no shirts.

These are 60mm tall legs made for the Ender 3 v2 neo.

Ender 3 S1 Pro Display offset bracket 5cm Raise 4.5cm Inside

From black Ender 3/Ender 3 Neo side cover to any color !

Front Cover For Ender 3 / Ender 3 Neo, perfect fit, keep V-slot in place.

This is screen cover for the Ender 3 V2/Neo to cover the bright screen at night for better sleep.

Updated filament guide from source to add a filament entry/exit. ...Made this fro my Ender 3 v2 Neo.

Ender 3 Offset Fan Vent 2.0 Original model found here: https://www.thingiverse.com/thing:3091510 Fan vent with offset arms that are completely clear of the hot end, minimizing warping from proximity heat. Added additional structure to the arms for...

This is a remix of https://www.thingiverse.com/thing:4665097 for the Creality Ender 3 v2 Neo because the rubber pads on the Neo were slightly too big to fit into the original design.

Полностью переработанный адаптер с выходом нагретого воздуха через штатное окно каретки Ender-3 NEO без потерь области печати и работы зонда. Правый воздуховод изменен под размещение Cr-touch. Позиционирование проставки и воздуховода на столе при...