ender 3 neo fan upgrade 3d models

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. This is a filament guide to help the filament enter the extruder at a better angle without...

Additional parts needed 2@ M4 X 16 screws 2 @ M4 T Slot Nut Fastener This is a top gantry LED mount for an END 3 Max Neo. It pairs with my X Axis gantry LED mount. https://www.thingiverse.com/thing:5931926. This design is good to give overall...

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

Lowered down fan so the heat sock can fit in without pressing against the fan duct (does require some support for a decent print, I recommend using tree supports and using them on baseplate only, this is up to you...

I remixed the Backplate for the Part Cooling Fan Duct by Zeltroix so it fits a Phaetus Dragonfly Hotend BMS.Fits Probably any other MK8 Sized Hotend too.

Printed in PLA , 0.8mm top, bottom and walls, with 10% Gyroid infill Remixed with Ender tool holder slide-in-rail clip , flipped over to print flat and resized to 110mm away from gantry. NB works well, but slide in clip could do with some resizing...

This is simple holder for memomry cards. ...It has one slot for SD Card, 2 USB slots and 3 microSD slots. ...It is mounted in the V-slots on the base.

I used a Nordlux Latona 4W white, a cheap led from my local hardware store. ... Size: 3,4 x 31,2 cm Where i bought it: https://www.bauhaus.dk/nordlux-lysarmatur-latona-4w-hvid

... ...I used original reel mount hardware to attach it to overhead gantry. I screwed the two pieces together for horizontal stability. the screw hole is 3.5mm. ...You can position the assembly wherever you like on the gantry to suit your needs.

This is a crucial modification I'm implementing on my Ender 3 to keep the barrel directly adjacent to the aluminum block for improved cooling performance.

- Added these zip tie mounts to the front to clean it up as you can see in the the photo with the USB in the front (printed at 60% size to fit small zip ties) --> https://www.thingiverse.com/thing:1800896 Updates: 4.21.2021 - Installed and...

... 3 V2 Neo, to provide improved and even cooling from all sides. ... Very clean and simple print with no supports needed This is a remix to fit Ender 3 neo printers from: DJIFF Edit: Added mk2 file that fixed some issues and cleaned it up a little bit

I found a remix of the system but it had so many issues with fitment and clearances, hot end cooling, ducts, etc that I remade the whole thing, but I need to give them some credit because they put a fair amount of work into it.(Can be found here:...

Ender 3 fan cover

Board fan guard Ender 3

I thought that the Mainboard of the Ender 6 doesn't need an extra Fan but a test without, the heat sink was untouchable hot(!) So just use calbe ties or M4 screws to mount the Fan on the Holder. To screw the holder on the Ender 6 you can use M3x5...

Complete upgrade\remake packet for ENDER 3 \ 3 Pro v1 to DIRECT print head with BMG extruder and E3D Volcano hotend. All parts makes together fully useable and long-time useable 3D printer for 24\7 printing withoutt any issues. This SET is only for...

Support for Ender 3 Creality Fans

Controller fan cover for Ender 3

... M3x6. For a fan 40x40x10 a spacer is included. ATTENTION: The original fan on my Ender 6 uses 24V. Noctua fans in this size are only available in 5V and 12V. Therefore you need a step-down buck-converter. The Fusion 360 file is attached. ...

No need to upgrade any fan, just make sure you undo the cable relief behind the fan and it will still reach the connector port as expected. You will see once the new shroud is in place the nozzle is slightly off center. this is expected. one port of...

Ender 3 enthusiast shields up! ...Customized Ender 3 fan guard + personalized Ender 3 moniker in one sleek design.

Ender 3 ventilation cover to protect the fan. ... Ender 3 Lüftungsabdeckung zum Schutz des Lüfters.

 Easy to print Fan cover for Ender 3.

My first 3D model is fan cover for Ender 3

Ender 3 Replacement Fan Blade. ... Print Tested: No.

This is a modified filament cooling fan duct for the Creality Spider HiTemp Hotend. ... The base for this is the "Mistral-E Filament Cooling Duct".

Ender-3 Fan block 3010 Fan * 3 M3 Nuts * 12 M3X16 Screws * 12 M3X10 Screws * 2

Remix of the original fan to fit the ender 3 hot end fan.