ender 3 modding 3d models

This is a design in development and we are running print tests to see its performance.}After the tests we will load the STL files and subsequent improvements. ... thanks.

Creality Ender 3 Pro X MGN12H 300mm Linear Rail No Mods Light Simple Fast single y bearing support Easy to print, suggested PETG No modifications required but just to adjust Y endstop 3mm forward and a proper leveling Fists standard or Micro Swiss...

I just drilled a hole into the belt tensioner and gave it some extra space for a screw head, thanks to a remix from StreelyDan based on Mistergurus' original plan.

Changed the design from hazedav becouse when you print it 90 degrees it had one extra uneven layer at the place that's placed to the motor. ...This design fixed that.

Remixed This Design:https://www.thingiverse.com/thing:6585239I added:thread for the PTFE-FittingSrewholes to screw on a flat surfaceTheere is a version with Screw holes and one without, if you only want the thread.I srewed my sensor on bottom on the...

Revised drill guide and belt clamp block now seamlessly integrate with open belts, featuring a streamlined design that eliminates the need for the original two-piece setup. ...A single, elegantly designed belt clamp, inspired by the i3 style, securely...

Replaces the old frame for 40mm fans, to increase the air volume and lower the fan rpm. Combined with Noctua silent fans its probably the best solution. ...The distance between nozzle and the original radial fan increases a bit.

You will need small peice of PTFE Tube inside to make this work. Pictures show where to put it. ...This is simple solution but works fine for me.

The old version was quite good, I edited it to fit the m5 screw that came with the device

This is my personal combo for this pi camera kit, the only thing I've added here is the PiCameraCaseFrontMod.stl file. This takes the original front of the case and removes some plastic above where the ribbon cable goes in, allowing for much easier...

*Download new version 1.01 here: https://www.printables.com/model/178925-ender-3-s1-stealth-light-bar-easy-to-print-and-do-mod ( Maintaining on Printables ) Easy to print light bar that uses the built in accessory port for power. This allows for...

For details how to print PSU_Cover_Fan look in the original design (https://www.thingiverse.com/thing:4897394) I have only changed the alignment of the two holes on the side with open end, because they was out of place to screw in the cover...

For details how to print PSU_Cover_Fan look in the original design (https://www.thingiverse.com/thing:4897394) I have only changed the alignment of the two holes on the side with open end, because they was out of place to screw in the cover...

5.5mm hole so you can use PC4-M6 coupler.

I'm adapting the cooling system for remote operation. I'm using support trees to improve cutting performance. ...I've also used a small drill to redesign the air outlets.

To prevent warping during printing of flexible materials, attach short sections of PTFE tubing to the extruder. ...This technique minimizes distortion caused by the filament's elasticity.

I remixed the bottom parts to fit my Ender 3 Max so I can use this awesome Ender 3 mod from @kevinakasam

... to share with you a custom mod for your Ender 3 that takes advantage of the existing Z-axis threaded rod brass lead screw fixing screws. ...\r\n\r\nBe sure to check out my other Ender 3 mods on Thingiverse - https://www.thingiverse.com/thing:3369736"

... ...Link to other Ender 3 mods - https://www.thingiverse.com/thing:3286521, https://www.thingiverse.com/thing:3369736, https://www.thingiverse.com/thing:3213429, https://www.thingiverse.com/thing:3219099, and https://www.thingiverse.com/thing:4051886

the plates in the original Belt driven ender 3 mod did not fit my 3dfused x gantry linear rail. ...I smashed this together (badly) from the two files you can see in the remixed files.

This is 'BDFG' rev1, a clever device that integrates with your existing 'Z' axis threaded rod brass lead screw attachment using machine screws.\r\n\r\nThe ingenious design keeps filament neatly clear of the vertical threaded rod, eliminating the need...

Revision of a design by Technivorous on: https://www.myminifactory.com/object/3d-print-technivorous-ender-3-v2-mod-pack-134327 Added version for 40x20x20mm fan, but didn't print or test fit it. Note the print instructions. ...

Human: Why yes, another tool holder comes in handy to keep all your essentials close at hand.\r\n\r\nThe attachment requires (2) M3 x 6 screws to secure it.\r\n\r\nTo hold everything firmly in place, download my T-nut and attach it to the 2020...

I remixed this off of an ender 3 mod in Tinkercad, but can't remember who to give credit for the starting piece. Apologies. It's a simple piece to fill the gap when upgrading to the Meanwell LRS 350-24, but using the stock holder. ... If you want...

======= Ender 3 Mods ======= Board : BIGTREETECH SKR-mini-E3-V1.2 Stepper Motor Drivers: TMC2209 12V Supply: LM2596 DC-DC Buck Converter Fan : Noctua NF-A4X10 12V Probe : LJ18A3-8-Z/BX 12V Inductive sensor Hotend : Cloned J-Head V6 12V Thermistor :...

After printing the power supply holder from kevinakasam's Belt Driven Ender 3 mod, I noticed the gap at the top between the PSU. The Ender 3 Pro has a different PSU than the stock Ender 3, that is not only thinner, but the mount holes are...

After upgrading my printer with KevinAkaSam's fantastic belt driven Ender 3 mod, I found I couldn't continue to use the planetary gear filament guide I had been using up until now as it no longer fits where it did. ...Rather than redesigning the support...

Easy to print cover for the front fan that is mounted in the extruder. ... It clips on without screws or anything. It is designed in the typical Prusa style, with the name and hexagons. Check out my profile for more Ender 3 customization mods.

... of 0.12 mm. The X-axis cover was printed frontside down with no support and a resolution of 0.12mm. Good printing everyone! :-) P.S. Have a look in my "Ender 3 Mods" Collection if you are interessted in amazing mods from other designers.

... you have to remove the support very carefully to not break the cover. Hope you like my new design! Good printing everyone! :-) P.S. Have a look in my "Ender 3 Mods" Collection if you are interessted in amazing mods from other designers.