ender 3 mks gen l 3d models

It appears that you've provided a long text about the conversion process of an Ender 3 printer, specifically focusing on the steps to perform a thorough check and calibration of the printer's components. Here are some key points summarized for...

I was searching for a control box to fit my MKS GEN L, TL-Smoothers, MOSFET and Pi Zero. Plus, I wanted to be able to still easily connect a USB cable to both the MKS GEN L. It replaces the CableChain_40MountSide from the cable chain at...

Chollos 3D https://t.me/chollos3dMasQFilamentos COMUNIDAD CREALITY ENDER https://t.me/CrealityEnder3Original MAXUS MARLIN TMC_2208 en Standalone proteccion thermal runaway activa Sd suport activo para modulo externo Iconos fullgrafics de serie...

Box for Mark-Six Gen L on Ender 3 printer.

Mainboard Case for Creality Ender 3 Printer, featuring a socket for mounting a Noctua 40x40x12mm fan.

This is a detailed guide for the MKS Gen L case of Ender 3. When assembling, use M3 screws exclusively. If you'd like to suggest improvements, feel free to leave comments below. Consider showing your appreciation by donating an amount of your choice...

I noticed some unused space that could easily accommodate a couple of extra buck converters, making the SKR 1.3/MKS Gen L half with its extra posts an ideal spot for them. The rest of the necessary components can be found in the Ender 3 all-in-one...

This only includes the SKR 1.3/MKS Gen L half with the extra posts for two more buck converters. ...The rest of the parts can be found in the Ender 3 all in one, universal rear electronics case Thing by Teaching Tech at...

This box, slightly larger than stock, has the ability to house: • MKS GEN L • MOSFET • Buck Converter (x2) • Raspberry Pi Zero W The base of the box will house your MKS & MOSFET boards, the side wall will house your buck converters and finally the...

This will fit an Ender 3 with an MKS GEN L version 1.0 with 3 buck converters, 1 Raspberry Pi B+ and a relay. I use this: 1x buck converter to power Raspberry Pi (for OctoPrint) 1x buck converter to power LED's on my Ender 3 1x buck converter to...

Added a MKS gen L version - just removed the SD card, everything else fits fine. Single fan covers added to improve airflow. Old design photos show new fan grill addition. Ender 3 Pro box now has an improved design. I created this box because I...

Made a slight modification so the USB port of the MKS Gen L fits. Print as Mr. ...Clown has described: https://www.thingiverse.com/thing:4501568

Made a slight modification so the USB port of the MKS Gen L fits. Print as Mr. ...Clown has described: https://www.thingiverse.com/thing:4501568 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: ...

The enclosure for the Creality Ender 3 Ctl Board swap comes into play. ...The MKS Gen L used board takes center stage.

Secure enclosure for mainboard assembly kit standard one on Ender three printer.

Here is a rewritten version of the text: This remix adds a cable chain connection point to the SKR/MKS Gen L Ender 3 enclosure designed by makermelissa on Thingiverse. ...I've included the cable chain connection on the bed as per my preference.

Box designed for Raspberry Pi and MKS Gen L on Ender 3 Pro. Ports are located at front for easy access, boxes mate with dove tails. Suggestions and feedback welcome! If you like this design consider clicking that "Tip Designer" button! To do: -...

... on Thingiverse, specifically https://www.thingiverse.com/thing:3502425. ... For those who are curious about my Super-Silent Ender, I've written an article that provides more information here: https://www.3dpedie.cz/en/inspirations/octoender_by_kiron/.

--- This is Version 2 of my Modular Control Box for the Ender 3. It's still a work in progress, but it's getting there. I'm printing it again to make sure everything lines up and works correctly. So far, so good - most of it is printed and I'll be...

Since I'm upgrading my MKS GEN L with TMC2130 stepper drivers in SPI mode, I realized that the original box was too low for the spi cables and a fan from above. Even without the spi cables, you probably need more space for the heat sink. To solve...

I was searching for a control box that would perfectly fit my MKS GEN L, Raspberry Pi 3B and a Buck Converter (LM2596) in place, while still allowing me to easily connect a USB cable to both the MKS GEN L and the Raspberry Pi. Since I couldn't find...

Redesigning Teaching Tech's MKS Gen L case for the Ender 3 is my goal, re-engineering it so that you can now easily create it from wood or plastic with laser cutting capabilities. Using 3mm birch wood, I significantly reduced fabrication time,...

Complete case for board maker's general L or board maker's general 1.4. Top part of the cover features a magnetic mount. Magnets used are 4x2mm in size. ... Magnets can be found at the following link:...

I revamped the TeachingTech design, removing the protruding fan component that bothered me, and seamlessly integrating an Ender logo into the sleek new build.

Hey from rainy germany, that's my custom made control box for the MKS Gen L + 3D Freunde MOSFET V2. You should use 2x 40mm fans in the front to get enough cooling. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter...

Hey from drizzly Germany, that's my bespoke control box for the MKS Gen L + 3D Freunde MOSFET V2. ...You should employ two forty-millimeter fans in the front to achieve sufficient cooling.

But it's definitely the best case to use for the SKR 1.3 and the MKS Gen L boards. UPDATED: 05/28/2019 A few people have commented on how tight the print fits on the Ender 3 printer. Yes, it's a tight print and if you don't have your printer dialed...

It took a lot of measuring to get it right, but this case is now the go-to choice for SKR 1.3 and MKS Gen L boards. UPDATE: Some users have pointed out how snugly the print fits on the Ender 3 printer. Yes, it's a tight fit, and if your printer...

I made myself a box for my Ender Pro because I wanted to make it quieter by installing a MKS Gen L and new drivers.\r\nAs I kept the original screen since I wasn't interested in TFT, the SD card reader is connected to the motherboard and therefore...

Panel mount USB enclosure taken from https://www.thingiverse.com/thing:1166631 I utilize two 12v, 60x60x10 fans, paired with an LM2596 module. You can opt for one fan, thereby freeing up more space for cable management. ... Update 2019-04-11: STEP and...