ender 3 mesh bed leveling 3d models

... will need to print four "muelles.stl" files, three "cama.stl" files, and one "cama trasera.stl" file. The "cama trasera.stl" component has a unique feature - it provides extra support for the bed cables, located in the left rear corner of the bed.

This is a remix from gulfcoast_robotics. ...I just made room on the right side of the handle for the silicon bed spacers. ... I did mine at 100% infill because the wall near the right hole is much thinner.

I simply drew a wheel with an M4 nut print that comes to lock your leveling wheel after adjustment. It works very well. ... Of course, you need 4 M4 nuts that you glue into the cavity.

Always struggling to keep paper clips in place on the glass bed, this innovation promises to be the solution. ... (Sorry again to earlier downloaders, but an updated version has been made available, featuring straight clips that open on both ends - a...

Liked the original model, but don't need for camera mount. ...Made the spring cups same depth to match bed cable strain relief. Note: this was designed to fit springs up to 8mm in OD. ...Files ending _10.stl should work with 10mm OD springs

There are countless bed handles out there, but this particular one steals the show as the most adorable of them all. It's sure to bring a smile to your face and make your day just a little bit brighter. ...Enjoy!

Frustrated users are constantly battling with paper clips that keep falling off the glass bed. ...To put an end to this annoying problem, a simple yet effective solution has been developed: straight clips now open on both ends, eliminating the need for...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Bed square for cristal.

I built a simple scrapper using TinkerCad, equipping it with a curved design that allows me to pry parts loose from the bed without lifting them. So far, this solution has worked flawlessly, prompting me to share my creation. I printed the scrapper...

Using the original (https://www.thingiverse.com/thing:2957507), I ended up with some problems with leveling the table, so I decided to look for one that doesn't fit the screw, and I ended up finding a remix of the original...

... (PLA case). M3 bolt (bolt and nut) and Super Glue are needed to fix them on the respective parts. I use these clips to hold the glass that I put on the printer bed, the original clips work but they seem to be forced by the increase in thickness.

Square bed for crystal glassware.

Learn more about this via Michael on ‘Teaching Tech’ here: https://youtu.be/mAU7cIZ0Hns This is a remix of ‘Ender 3 Level Test’ by elmerohueso (https://www.thingiverse.com/thing:2987803) with two key changes needed for the Ender 3 Pro: 1.) A cold...

Customized version of https://www.thingiverse.com/thing:538624 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=538624

Easy to print bed level indicator friction mount for the Ender 3 V2 hotend. https://youtu.be/v5vvQYXLw78 -- Required Parts 1x Indicator (~7€) [https://de.aliexpress.com/item/1000004974110.html] 1x M2.5x40 extender (~4€)...

This product is designed for use on Ender 3, Ender 3 Pro, and Ender 3 Pro V2 printers that utilize the 60mm (large) leveling wheels and feature the original bed carriage plate. It may also work with other models that have 60mm wheels or upgraded bed...

Very simple sensor holder for M12 inductive bed level sensors. Could be mounted easily on original Ender 3 Pro hotend. Use normal M3 screw and hex nut for clamping the sensor instead of using the provided M12 nuts. ...That make the design smaller and...

I designed a Bed Level holder for my digital drape pattern gauge that I can click on my Ender 3 Pro to secure it in place, easily remove it by pushing it aside and letting it go. ... I'm using a drape gauge purchased from here:...

Additional instructions can also be found there - https://www.printables.com/model/422895-ender-3-s1s1-pro-locking-bed-level-knobLet me know if there are any problems with the model, as I haven't handled this with the S1 Plus and was only relying on...

This is my take on the standard Ender 3 bed level calibration. Instead of relying on a piece of paper, this file is tailored to be used with a precise 0.1mm or 0.004" feeler gauge or shim stock. By doing so, all inconsistencies associated with paper...

For Ender 3 or Ender 3 Pro users, this printer delivers a maximum-sized skirt print within 10 rounds, pausing on each lap to make crucial adjustments. It's highly recommended to tram the bed with a piece of paper first, providing a rough level for...

This is designed to bolt right up to the Ender 3 V2 hot end mount. I designed this to hold 18mm sensors (both capacative and inductive). You will need two screws (I think M2.5x0.45) for the mount to frame and one coarse screw to clamp the sensor.

Place your paper at this point to adjust the bed's levelness; once you've completed the task, press the printer button, and the nozzle will move on to the next point. The nozzle will visit all four corners and an additional four points in the...

If it's not too much trouble, I ask that you download my models from printables (https://www.printables.com/model/422895-ender-3-s1s1-pro-locking-bed-level-knob) if you don't intend to "tip the maker" so that I can receive some points towards...

Once there is tension it is not necessary, therefor a thinner plate works • Increased sidewall thickness, this is where the torque is • Removed extra material from the bottom of the assembly to save on filament • Moved the screw hole closer to the...

Bed leveling knobs designed specifically for the Ender 3 feature a locking nut for secure adjustments. The dimensions have been carefully remixed to match the original stock knobs, including a slot perfect for inserting a nyloc nut - compatible with...

These also work as excellent bed levelling nuts for the Ender 3. Combined with upgraded springs, you'll never have to worry about knocking those massive wheels again! Be aware that these only leave 14mm of usable space between the electronics cover...

Bed Handle with Bed Locks that I threw together from a few files in 3D Builder for Ender 3 Max (or any bed with a 300x300 bed size) Here are the original files: https://www.thingiverse.com/thing:4856613 https://www.thingiverse.com/thing:5364491...