ender 3 max 3d models

Currently untested remix of Ender 3 Max Direct Drive brackets using stock extruder parts, fitted for use with Hero Me Gen 5/6 Updated to V2 with increased wheel clearances and slotting for the threads protruding from the back of the carriage plate

This is a fix for Ender 3 max neo with sprite extruder pro upgrade auto leveling crash into far right end of X axis. This X limit switch cover compensate the new print head X offset position. M851 X-31 Y-45 ; CR-Touch probe offset from nozzle. ...

To fit the original Creality Ender3 Neo LED Light Kit 24V 5W Ender 3,Ender 3 V2, Ender3 Pro, on the Ender 3 max NeoIt is necessary to extend the original cables of the LED strip so that they can be connected to the right side of the lampEs ist nötig,...

Mounting plate was canged accordingly to Ender 3 Max's x carriage 3. Direct drive mount was moved higher because paragraph 2 Everything should be printed as is WITHOUT supports. All changed models are here, other parts are acquired from original...

Mounting plate was canged accordingly to Ender 3 Max's x carriage 3. Direct drive mount was moved higher because paragraph 2 Everything should be printed as is WITHOUT supports. All changed models are here, other parts are acquired from...

Hi, I've been using this BantaMount re-design for quite a while and decided to share it with everyone else!Firstly I had to slightly redesign the basic mounting system to fit the Ender 3 Max by removing a part and adding two screw holes to the...

I have changed several things: All heat inserts were changed for M3 Nuts Mounting plate was canged accordingly to Ender 3 Max's x carriage Direct drive mount was moved higher because paragraph 2 Everything should be printed as is WITHOUT supports. I...

Added the Marlin 2.0.7.2 firmware for the Ender 3 Max based off the Ender 3 Pro firmware but supporting the larger bed size and filament runout sensor. I used the 5 pin header on the board to connect the BLTouch but had a 3 + 2 pin bltouch cable. One...

Bed Handle with Bed Locks that I threw together from a few files in 3D Builder for JG Maker Artist-D and Ender 3 Max (or any bed with a 300x300 bed size) Here are the original files: https://www.thingiverse.com/thing:3363720...

Then I try to search and found chain that clip on extruder motor, so I try to combine itOn recent photo I already use Belted Z mod but it is same position / can be use on stock gantry that still use lead screw :)I already do mod on left gantry for...

The Ender 3 Max is a cracking printer and a good step up from the previous E3's but despite pre-release feedback Creality for some reason still went with a fixed z-stop. The go to fix for this is to swap out the two bolts holding the z-switch bracket...

I needed a mount for stock fan on my Ender 3 Max for the Micro Swiss Direct drive extruder. holmes4 had one listed for a BL Touch but the mounts didn't line up. But I'd like to thank him for the inspiration. I have a CR Touch and I wanted it on the...

I needed a mount for stock fan on my Ender 3 Max for the Micro Swiss Direct drive extruder. holmes4 had one listed for a BL Touch but the mounts didn't line up. But I'd like to thank him for the inspiration. I have a CR Touch and I wanted it on the...

Ender 3 Max meanwell psu tools holder. 2nd attempt at uploading this newly revised set. This is for anyone who has fitted dual Z screws and moved the meanwell PSU off the gantry leaving a little space to play with. I discovered that there are 2...

... a tower and that is it. Designed in Tinkercad, you can find it there https://www.tinkercad.com/things/hjkWfwTej8s-camera-mount-ender-3-pro-y-axis And you can download and tinker to your hearts content. ... Excuse all the experiments on the side....

... a tower and that is it. Designed in Tinkercad, you can find it there https://www.tinkercad.com/things/hjkWfwTej8s-camera-mount-ender-3-pro-y-axis And you can download and tinker to your hearts content. ...Excuse all the experiments on the side....

I looked and looked for something that would work and found [GAFFER7773_ZA](https://www.thingiverse.com/GAFFER7773_ZA)'s *[Ender 3 Max HeatBed Cable chain Back Mount](https://www.thingiverse.com/thing:4981719)*. You will need to print GAFFER's [hook...

... change it to put in rails to slide into the side of the chassis of the Ender. Confirmed that even though this is designed for Ender 3 Pro, it DOES fit my Ender 3 Max nicely. ... Same set of screws as the original design was used to put together

made a print in place filament guide that changes angle and it is plug and play with the frame of an ender 3 neo max.

version two will mount to the printer and filament sensor the same way as the original though there will be three different parts and some fitting or super glue may be needed I could not find a nice compact mount for my direct drive converted Ender 3...

I created this X-axis cover to dress up my Ender 3 Neo Max. You must print the x-axis cover with the logo first and then print the color insert in your favorite color. The color insert becomes the color of the font and logo when super-glued behind...

Humans require maximum area for efficient cooling while minimizing fan obstruction to optimize airflow.

**UPDATE** I made an accompanying LCD cover, which can be found here: https://www.thingiverse.com/thing:5824152 This is exactly bawesome's remix but I just removed the pi cam thing on the side and ribbon slot since I already had a webcam setup...

Customized version of https://www.thingiverse.com/thing:34558 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=34558

<p><i><strong>Update 8/17/22 to v2</strong></i></p><ul><li>Moved Biqu H2 mount holes a tad further to the left. ...I found that in v1, the motor magnet could interfere with the BL touch.&nbsp;</li><li>You can now hide your wiring behind the new cut out...

I got tired of unscrewing the little screws on the case to get to the hotend. The result is a hotend cover that can be lifted off to access the hotend or change the nozzle. The cover is smaller and lighter than the original. I improved the...

When installing this, it is very recommended to use two of the same fans. The fans can be soldered in series. I am unsure if it's compatible with other printers. It's still work in progress, next thing i'm adding is a part for cable managment.

If your new shiny hotend doesnt fit i have the solution for you! After recieving my creality spider hotend I found out that it doesnt fit in the normal schroud. I didnt like the solutions provided by creality and did just want to use the normal...

4x M3x20 Screw 1pc PTFE Tubing as desired (2x4mm) Replaces the filamentsensor (turn it off in the menu)

<p>print on its side no supports required 100% infill of 5 walls</p>