ender 3 max upgrade 3d models

I installed an Ender 3 board and display on my Ender 2. The tiny LCD screen that came with it had become increasingly difficult to read due to my aging eyes. ...I opted for a straightforward upgrade, swapping out the original housing for a...

Compatibility: Ender 3 v2 Ender 3 MAX **Any printer that has a 40x40 Y-axis extrusion underneath like the machines mentioned above. You will need some M3 nuts and bolts with varying lengths for affixing the parts. Two m3 nuts and bolts for the...

When cleaning out a clog I accidentally broke the coupler that attaches the bowden tube to the extruder on the Ender 3 Max, so I modelled a new one. After 3–4 iterations it came out pretty good. Insert the coupler into the extruder and then push the...

I added a second stepper motor and leadscrew to my z axis of my Ender 3 Max. To accommodate this, I needed to remove the power supply form the right vertical support where Creality had originally mounted it. I wanted the power supply to be mounted...

The heat creep from the hot end and the trapped air in my printer enclosure were causing the filament to soften and the extruder gear on my Ender 3 Max to grind it down until it eventually snapped or stalled. So I designed this little fan mount to...

I designed this to work with the ender 3 max print head while using a 60mm and a 40mm fan. As of now, this is the 15th version of the design, however, I can't say it's 100% finished (more like 90%). So far, my printer has been working fantastically...

This is designed for use when adding dual z axis rods to the ender 3 max. You will need 8 m4 bolts and t nuts for the relocation kit. To mount the psu to the rear extrusion you will need to pass the bolt through the vent slot near the green LED in...

One more Z brace for Ender 3 Max.This time for motor side of extrusion profile.This brace is designed with motor support in mind so it does not hang in the air pulling everything down.It is adjustable vertically for a few mm. Since i have...

... it? Visit ...insert link here... to get yours shipped to you!Print SettingsPrinter Brand:CrealityPrinter: Ender 3 MaxRafts:NoSupports: YesResolution:.2Infill: 20Filament: Any PLA Any   Category: 3D Printer Accessories

However, I left a little bit of tolerance on the set of holes against the Z rail to accommodate a shim I and others have had to use to correct a width issue on some Ender 3 Max printers. This bracket works on both my shimmed and unshimmed rails. ...

If using PrusaSlicer, set support type to snug or else it will try to support everything underneath it!** ------------------------------------------------------------------------------------------------------------------------ **About the gcode print...

Filament sensor mount. ...for Creality stock sensor Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 40% Filament: Addnorth PLA-E Grey Category: 3D Printer Parts

Filament sensor mount. ...for Creality stock sensor Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 40% Filament: Addnorth PLA-E Grey Category: 3D Printer Parts

I decided to design a CR Touch mount for my Ender 3 MAX as my CR Touch never came with mounts at all. I searched for a little while for pre-made ones but didn't find anything I really liked so decided I would attempt my own one. It was designed in...

... your own holes. The center of the holes will be 10mm from the inside corner. I would also like to give @DutchShapes a big thank you for creating what I think is the best PSU holder when adding a second Z-screw & stepper motor to your Ender 3 Max.

Filament roller guide for Ender 3 Max. ...Designed to work with the filament roll relocated to the top of the printer and filament runout sensor in original location.&nbsp;</p><p>&nbsp;</p><p>Printed with 2 walls, 20% infill, PETG, no supports...

LED mount for Ender 3 Max Neo, should work fine for any Neo/V2 Ender Printers. I wanted an LED mount that would light the print as the Z axis raised. I tried a couple different mounts and this one worked best for me. One of my designed the LEDs...

After 3 weeks of failed design attempts, I have finally finished my time-lapse rig for my Ender 3 Max. I wanted it to be as simple as possible for easy printing and attaching to your printer. The finger attaches to the BL Touch bracket holes with m3...

My original fans started rattling like crazy, (and no one seems to be designing mods for the max ) so I hopped on the opportunity to design these adapter ducts to fit 4020 fans on the original Ender 3 Max fan shroud. They're not perfect at all,...

... are evidently needed. Inspirations: Camera Mount: [https://www.thingiverse.com/thing:4073125](https://www.thingiverse.com/thing:4073125) Ender 3 Max Bed Handle: [https://www.thingiverse.com/thing:4856613](https://www.thingiverse.com/thing:4856613)

Complete replacement to the Ender 3 Max Neo tool drawer to hold a Raspberry Pi 3, Buck Converter and Relay. Design of the tool drawer should work for Ender 3 v2 as well. The design is intended to use the original "case" for the tool drawer but...

... https://www.thingiverse.com/thing:5189951 (Have not yet printed it) I suggest to print this in a HIGH Temp material. TO EDIT THE DESIGN OR TEXT: https://www.tinkercad.com/things/h3f2AKz2DeJ Please upload your remix SUPPORT ENDER 3 MAX!!!!

My ender 3 max has been full of disappointments. First it came with all the eccentric wheels over tightened. Then the X gantry would droop, clogging the nozzle and giving horrible results (added a second Z axis stepper/screw to fix that). Then...

I drew this up to add a spool bearing to the stock Creality Ender 3 S1 Max. The spool pin is a quarter turn cam lock to the holder arm, but the pin itself is flanged on both sides, which presents challenges. I decided to split the inner race and...

I found that my Ender 3 Max hot-end was not getting enough air flow to print PETG. I decided to go the extreme overkill route. This adapter allows the installation of a 7530 24 volt blower fan. In order to install this you have to remove the old 40mm...

I've spent the better part of 6 months printing, and reprinting many different iterations of drag-chains, or cable chains, for the Ender 3 Max. I think I came up with a pretty decent solution. I have removed my filament runout sensor, but this...

... I can think to make it. This is "Version 1", so it may not be 100% accurate. I really just modeled it so I could design some custom fan shrouds and such. This may also work for the Ender 3 V2 Neo as well? I'm not sure. ...Do with it what you will.

so i tried the original on my ender 3 max...nope not gonna fit, but i liked the design as it keeps if done right almost 100 percent of useable space. so several remix and reremixes later after multiple failures for a bunch of picky issues i...

Only really useful to those who have added a version 2 vertical screen to their ender 3 max. I rarely use the screen as I use a pi zero 2w and octoprint for the majority of my interactions with the printer. I decided on a more compact layout and...

... a tower and that is it. Designed in Tinkercad, you can find it there https://www.tinkercad.com/things/hjkWfwTej8s-camera-mount-ender-3-pro-y-axis And you can download and tinker to your hearts content. ... Excuse all the experiments on the side....