ender 3 max neo upgrades 3d models

All measurements were made by me on the heatsink I received as part of the Ender 3 Neo kit. Some of the hole locations and some of the dimensions are different from other models I found online. ...For example, the heater mounting holes are centrally...

For designers to make custom print head and other mods for the X carriage assembly on the Ender 3 V2 Neo. Update 2-16-23 3PM PDT: Corrected the position of the upper left V-Wheel, was off by 4mm. Added a missing hole at the top right of center on...

I made this mount specifically to fit Creality Ender 3 V2 Neo. The camera I have mounted is the "Creality Camera" but you can mount any that fits dimensions. If you need it the part printed for any reason. ... Message me at through my Etsy account...

Ender 3 cover

I made this to relocate the Ender 3 V2 neo x-limit switch to support the Sprite Pro extruder which will not trigger the X-limit switch in the default location. You reuse the original screws and the limit switch and need to add two M3 bolts and nuts...

... 7:30PM PDT: Corrected the position of the upper left V-Wheel, was off by 4mm. Ender 3 V2 Neo X Carriage Model v2.stlUpdate 2-16-23 3PM PDT: Added a missing hole at the top right of center on the plate. ...Added second version without V Wheel disks.

User OpenDorrPolicy uploaded a really cool side filament guide for Ender 3 Max. However, I wasn't the fan of the need of using the screw. I redesigned it then. The anchoring part that hold the bearing has been changed to the one used by...

I extended the clip side to account for the overhang, and lengthened the left-most tab to catch.Extruder (Bottom) Mount: This came from a file on printables (https://www.printables.com/model/408734-ender-3-v2-neo-chain).Hot End Clip: This one is a...

Полностью переработанный адаптер с выходом нагретого воздуха через штатное окно каретки Ender-3 NEO без потерь области печати и работы зонда. Правый воздуховод изменен под размещение Cr-touch. Позиционирование проставки и воздуховода на столе при...

They have a length of 44.5mm without the extrusion slots and should work with the stock feet of an Ender 3/v2/Neo but I have also added spacers that can be placed under the feet which can be scaled in a slicer and I have added the .f3d file of the...

I made these feet to support the Y-axis on my Ender 3 v2 Neo to increase speed and acceleration.They require no additional hardware and can be easily installed by removing the four screws holding the Y-pulley tensioners and sliding the feet onto the...

Ender 3 V2 Neo is my first 3D printer. I bought a 2KG spool only to find it was too wide to fit on the stock spool holder. Started learning sketchup so decided to recreate the stock spool holder but make it about 15mm longer. Worked pretty well,...

This is an attempt on a Ender 3 V2 Neo x-axis cover. I needed it for a custom version later on , as a holder / bracket for a webcam. It turned out really well and fits as good as the original. ...Hope you might find a way to use it either as a...

It is a filament guide for the Ender 3 Neo (v1) that snaps right into place. It sticks out to the left of the printer by about 10cm, guiding the filament nicely in an arc instead of it going straight down. ... Sliced with Cura - Note: Support...

This is a mount for a Raspberry Pi to an Ender 3 NEO in a case. You need to create 2 of these to hold the Raspberry Pi. I added M4 screw holes, but so far haven't needed to use the screws. I also included the scad files to customize it to your...

A PSU Support for the Ender 3 Neo (Slim PSU) that I modeled. Despite those existing here, I have not found my happiness. I wanted it to adapt to the original bindings, but which is placed on the 4040 profile with the slides. I switched the power...

This is a Stand for your Ender 3 v2 NEO stock spool holder. It uses it's original screws. I guess it might fits older models aswell?! I built the IKEA Lack housing for my printer so I had to remove the spool holder. With this stand you can reuse...

I couldn’t find anything to my liking that fit the Ender 3 Neo 3D due to the wider stock hotend. I used the the stock screws for the hotend and one of the blower fan screws to hold this in place. M3 screws and heat-in inserts to hold the fans in...

... I'm not entirely sure if the dimensions of the profiles changed between the original Ender 3 and the Ender 3 v2 Neo, but at least on my unit, the slots in the profiles do not match the dimensions in the blueprints available from Creality on GitHub.

You can also raise the camera itself -after mounting it- for your liking.Print SettingsCreality Ender 3 V2 Neo - using Cura + Filament Friday Extra Fast 0.28 profile with 10% infill. Important: Print with a brim to help with adhesion. ...No support...

Ender 3 Max BLTouch ADXL345

Model description: Housing for LED strip for Ender 3 NEO printer.I used an 8.1 mm wide LED strip, 6.2 mm wide LEDs. I bought it here. Description of bodies:  Body1 - are two slats that are glued (optional) together at the bottom.  Body2 - is a cover...

I've colour matched my LED to the one that's included in the Ender 3 V2 Neo CR touch to make it extra snazzy, Just screw mount the Raspberry Pi to the drawer base. I used recessed M2.5 screws that screw into a heat-sink from the bottom up. Then it's...

I was tired of digging in the drawer for my Allen Wrenches... ...So, I made an Allen Wrench holder for the wrenches in the kit that comes with the Ender 3v2 Neo. ...Fit's on the top of the printer and is held in place by a T-Nut and a Cap Screw.

This is for an Ender 3 Neo with the extender 400 ender 3 pro kit . you will also need feet on the printer, I got mine here https://www.thingiverse.com/thing:5522084 . This is designed to house the 4.2.2 mainboard and a 120mm thin fan . I am hoping I...

For Ender 3 MAX (bigger than ender 3 pro)

This holder fits the V2 Neo which comes with a stubbier small wrench (10.5mm handle), which will now fit. This holder should work really on any Ender machine and non other brands that have the same/similar rail. ... Note: For best finish print like in...

Modification of the E3V2 design to fit specifically the Ender 3 V2 Neo Recommendations: a) Connecting the autostop switch in parallel of the printer switch (i.e. ...connecting both switch pin to pin), and not serially (as suggested in the original...

This support has been designed for those who, like me, own an Ender 3 V2 Neo and have added a Creality filament end sensor. Impossible to find on platforms so I designed a perfectly functional one. This pack includes: Stand The pulley The screw...

tool holder for the tools supplied with the ender 3 + a cutome case