ender 3 max dual z 3d models

Ender 3 Max 300 x 300mm bed level file. Just one layer high run with or without a skirt and level your bed to perfection in quick succession! This file allows you to make adjustments to your bed whilst printing in real time. Covers each corner of...

This is a rough Model of my Ender 3 Max Printhead (without the cover or Fans etc). Because i want to design my own Printhead cover and i couldnt find any models of it i just made my own. -Minor deviations I uploadet the Fusion Projekt for...

This is a remix for the Ender 3 Max of the infeed body from the "Cr 10 S PRO filament roller guide 608 bearing by L3D_Help_Guide". I adjusted the mount to fit around the filament runout sensor and added slots for an M3 hex bolt and nut so you can...

Ender 3 Max Filament Guide allows the filament to evenly spool off the roll. It prevents the filament from prematurely jumping over the filament's roll's sides. It prints as one piece. Simple to install; no need for hardware or glue. Support...

I designed this to help with designing hotend adapters for the Ender 3 Max since it has it's own model-specific plate as well as to get acquainted with fusion 360. I printed a thin template (red in the photos) and made small tweaks till the bolt...

I have modified and shortened Hook3D PSU switch's STL and located it on the left hand side of the ENDER 3-Max. Also, I added 2 brackets to hold the PSU fan down to avoid all the debris from fan's suck in force. All you need is: 1. 4 X M4 to...

Since i've installed the dual Z upgrade, i had to relocate my powersupply but i could not find anything simple to apply to relocate my power supply, so i've created my own solution. ... Things needed: <b>* 2X M3,0X8 BOLTS <b>* 2X 20-M3 T-NUTS ...

Handle for Ender 3 Max I suggest to print it in ABS if you plan to use your bed at more than 60º, if you print PLA all the time, you can print it in PLA. This handle goes abobe the bed plate for better stability, touching the springs and compress...

This is a 4040 vslot y tensioner designed for my Ender 3 Max. It uses the original bracket but adds a thick end cap to the 4040 vslot. I have also swapped out the original y belt pulley on my machine and I am using a gt2 idler pulley which is 8mm...

Measured and designed the Ender 3-MAX's mounting bracket in CAD to create my own mounting solutions.I already did a mounting bracket for the BIQU H2, referencing this model, which you can find here: https://www.printables.com/model/212910Just import...

Measured and designed the Ender 3-MAX's mounting bracket in CAD to create my own mounting solutions.I already did a mounting bracket for the BIQU H2, referencing this model, which you can find here: https://www.printables.com/model/212910Just import...

Direct drive for the Ender 3 Max There are 2 carriage styles, one with a Bowden tube connector (recommended) and one without a tube connector. (Original carriage file from here, https://www.thingiverse.com/thing:5191840). I modified 40x40x20...

Measured and designed the Ender 3-MAX's mounting bracket in CAD to create my own mounting solutions. I already did a mounting bracket for the BIQU H2, referencing this model, which you can find here: https://www.thingiverse.com/thing:4963613 ...

This is a remix of CUBEd_3D's Ender 3 Max filament guide. I remodeled it in Fusion 360 to help learn Fusion 360. You can use their roller and other parts with this arm. It requires a 608 bearing. If you have a well dialed machine you can print...

The model is from a user on thingiverse that i remade, i liked the logic behind it and it was pretty easy, but i wanted something to use with the stock EVERYTHING because i'm an asshole and do not want to spend money XD, i also moved the filament...

Ender-3 Pro Y Axis Dual LM Guide Upgrade Utilizing two MGN12 linear rails, each measuring L300 in length Eight M3x10 bolts are required for assembly Eight M3 washers will also be necessary to secure the components Four M5x15 flat head bolts provide...

Mount for the Matrix Extruder (Trianglelabs) for the Ender 3 Max. This may work for the original Hemera from E3D too. I would have bought it, if it would be available then..... This is work in progress. I have problems with filament clogs and...

I required an additional extension from the frame to fit in my dual Z motor alongside a PSU shroud that houses a front-loading AC power supply.

I'm making some slight adjustments to ensure compatibility with your remixed offset brackets, specifically to accommodate the dual Z motor clearance requirements.

I looked everywhere for a good setup for the Ender 3 max to mount the filament on the top of the machine and couldn't find a simple roller that would mount on the end of the runout sensor bracket so I just made one. Printed this at 50% infill but...

... is only useful if your filament spool normally sits below the level of the extruder and filament sensor. The next step is to add a connection for a drag chain over to the hot end that can connect to existing pieces designed for the Ender 3 MAX.

I did this so my Ender3 MAX Neo has a chain, and since no one has shared something similar i decided to share it, i used the work of wku_wake and norp to and modified some of their files You will need 43 chain parts for the Z and Y axis, and 20 chain...

Drawers for Creality Ender 3 Max. The drawers are designed to fit well to the space under the printing bed, and it will be fixed under the displays Metallic holder, designed while taking the board's ventilation in consideration. Features: ...

A thing I created to learn how to create and print 3d models with my new Ender 3 Max, and of course be useful.. It is a work in progress although fully functional already I intend to modify so it clips onto top v rail instead of having to remove...

Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Notes: For the most part supports are unnecessary and minimal but it shouldn't hurt print times to use them. Most angled faces are at...

https://youtu.be/m6cBTyH40SUhttps://youtu.be/ePZmgOYSZPw Reinforcing cross brace for the printer frame Double Z-axis with two motors - method of design Magnetic anti- wobble nuts on the trapezoid guide screw These modifications lead to improved print...

I wasn't happy with the brackets that came with my dual Z stepper upgrade kit - so I designed some new ones that are stronger and also have slots in so you can adjust the height of the power supply. You can even lower the power supply so it is flush...

I modified the long version to cut about 24mm of height, allowing for a more robust holder that fits after dual Z belts have been installed. The design remains largely unchanged apart from this adjustment. I've included the source file for you to...

Highly Recomend 3d printing this cheap and easy model&nbsp;I colored the ender and dragon in with silver sharpieHappy Printing

Just a quick mount I made for my webcam to lift the camera with the z carriage. Used to monitor print with AI. ...