ender 3 max dual z 3d models

This is my take on Ender 3 Max dual Z axis update. ... I did use closed loop belt 852mm from here: https://www.aliexpress.com/item/32971350055.html Belt tensioner (or belt cut to size - glued and sawn): https://www.thingiverse.com/thing:4796015 also...

Ender 3 Max dual z height sync spacer used to sync the heights of your Dual Z axis can also be used to help set the Z axis rollers made to utilize and clip into the T-slots in the extrusion the file provided is the LH side, copy and mirror for RH...

Ender 3 Max dual z height sync spacer used to sync the heights of your Dual Z axis can also be used to help set the Z axis rollers made to utilize and clip into the T-slots in the extrusion the file provided is the LH side, copy and mirror for RH...

I recently installed a dual Z axis kit on my Ender 3 Max and wanted to link the lead screws to keep them in sync. Some people have luck simply adding a 752mm belt between the screws, but this was far too tight on my copy and caused binding starting...

Here is a simple Jig to mount your stepper motor for DualZ mods. ...its a  snapfit so needed extra hardware

Here is a simple Jig to mount your stepper motor for DualZ mods. ...its a  snapfit so needed extra hardware

I upgraded to the second dual Z screw on my Ender 3 Max and needed to relocate the Power Supply so I made this bracket. Make sure you ground the power supply! Printing: Infill - 30%-100% (I like 100% for structural components) Supports - No ...

Gantry Dual Z Ender 3 MAX

Ender 3 Max meanwell psu tools holder. 2nd attempt at uploading this newly revised set. This is for anyone who has fitted dual Z screws and moved the meanwell PSU off the gantry leaving a little space to play with. I discovered that there are 2...

Remixed the Ender 3 Max dual z height sync spacer from scratch to fit the Ender 3V2. So basically I took the idea and made a new version to fit my needs. Used to sync the heights of your Dual Z axis. And can also be used to help set the Z axis...

This is a Z-max endstop that leverages the original z-min endstop switch, seamlessly integrating into the extrusion with a precise press fit.\r\n\r\nUsing this setup with a Duet Maestro facilitates power loss recovery for added...

This is a Z-max endstop that uses the original z-min endstop switch, the part press fits into the extrusion. I am using this with a Duet Maestro for power loss recovery. I have also remixed clips to keep the endstop cable tucked into the extrusion...

Adjustable end stop for the Z axis.

This is a Z-max endstop that uses the original z-min endstop switch, the part press fits into the extrusion. I am using this with a Duet Maestro for power loss recovery. I have also remixed clips to keep the endstop cable tucked into the extrusion...

Dual Z for Ender 3 V2 without second motor Material needed 2x Pulley GT2 6mm 1x Belt GT2 6mm --> 610mm closed 3 x Roller's --> F688ZZ 1x Lead screw T8 | Pitch 2 mm Lead 8 mm -->400 mm

**Non-Stock Parts Needed - Stock Bracket Replacement** - 1x M8 washer (to place under the eccentric nut so it doesn't wear through the plastic) - Suitable motor (NEMA17, get one like the ones on the Ender 3) **Non-Stock Parts Needed - Second Z...

I remixed mlynch002's design because I wanted my printer in the original location, so my ender would fit better on my desk after adding the dual Z screw. I highly recommend the dual Z upgrade, and my remix uses about half the filament and print time...

I remixed mlynch002 because I wanted my in the original location and so my ender would fit better on my desk after the dual Z screw was added. Would highly recommend the dual z, and my remix of his design uses about half the filament / print time,...

Wiring: So far, I've only tested wiring a second stepper in parallel with the original stepper, increasing current to 1 amp (Skr 1.3 with 2208). Also, my second stepper is different from the original Creality stepper, which isn't recommended. I'll...

This is a remix using tinkercad.com to remove a 30x3 mm section to wrap around the x-axis belt tensioner on my Ender 3 v2. The tensioner sticks out so the part that takes the place of the spacers can not lay flat without removing some of the part. ... ...

Parts: KLF08 Bearings: https://de.aliexpress.com/item/32793159224.html Ender 3 Rod: https://de.aliexpress.com/item/32904246004.html GT2 Timing Pulley: https://de.aliexpress.com/item/33017482340.html GT2 Belt Joining:...

This fix the problem with Ender 3 Max Z endstop calibration using the same screws. ... Dimension: 41.2mm x 49.7mm x 10mm Approx print time: 45 minutes

simple addon to support on the ender 3 max

it works really well, and is designed to fir the standard ender 3 max plate. you need to remove the heating cartirage and thermister to route it throught the duct. this was to make it possible to mount on the ender 3 max plate. but it takes 2...

I have designed this z axis brace for my ender 3 max. I had problems with unstable z axis problems since i bought the printer, andi tought it could be braced like on the cr10 series. The parts need to be mirrored to get it for each side. Parts you...

This fix the problem with Ender 3 Max Z endstop calibration using the same screws. Dimension: 41.2mm x 49.7mm x 10mm Approx print time: 45 minutes Print Settings Printer: Ender 3 Max Rafts: No Supports: No Resolution: 0.20 mm Infill: 20% Filament:...

Just got my new Ender 3 Max and was disappointed to find that my Z endstop was so high that I would have to completely loosen the screws on the bed to get the extruder to touch the bed. This fixes it so that it is close enough that you only need to...

However, I left a little bit of tolerance on the set of holes against the Z rail to accommodate a shim I and others have had to use to correct a width issue on some Ender 3 Max printers. This bracket works on both my shimmed and unshimmed rails. ...

Print 2 if you have the dual z axis like i do, cannot confirm other fitments so let me know what it fits and I will update the listing.

I don´t know if this is machining problem only in my printer but maybe this can help to someone else. I put this spacer in the left side of the printer (in my case 1.2mm thick, you can modify to your needs) so now the x gantry can run smootly along...