ender 3 mainboard cover 3d models

Unfortunately, after printing it out, I discovered not only were the arm sides asymmetrical but also the underside of the fan cover was flat and far from aerodynamic - or symmetrical for that matter. To fix this issue, I streamlined both side arms to...

... Though, even with the cover as short as it is, it blocks all the light and only has a very dim glow. Use as much infill as you think you'll need to block the light. I used 30 percent infill, I think, with white PLA. Also, no supports needed.

Another Ender3 Fan cover, but who doesn't like variety Best results at 0.2mm Was made using a CAD model and printed in real life without any problems. Possible to print without support but there is a bit of overhand at the top. Without support,...

... annoying, I've got a straightforward solution for you. ...The cover slips effortlessly into the screen casing, effectively blocking the light emanating from it. ...It boasts an uncomplicated design that can be printed swiftly in nearly any material.

... a 20-gauge or .88mm steel wire for the hinge, which can potentially be replaced with 1.75mm filament. A black color is highly effective in concealing light from view. The holder is strategically positioned between the screen cover and LCD screen.

2 Options 1 with the hinge on the Case and the other one is with an solution to glue the hinge at the Case. ... I need to prepare the hinge and the cover with an 2mm screwer, than a Nail or 1,75mm Filament can fix it toghether.

I needed an LCD cover to use when I spray the lacquer on the plate. This version has a sliding window on an L-shaped frame and does not clutter laterally when open. ...For fixing, use a few pieces of double-sided tape.

I had to create it myself, it's just the insert to cover the profiles to prevent them from collecting filament scrap. You can easily adjust the length to your needs in your slicer, just remember to unlock the "preserve aspect ratio"! ... Printing: ...

Two options: Frame only - 2x faster print and enjoy LCD PCB glowing in the night :) Full cover - extra protection. Both are mounted by factory screws, just cut the left corner along marking with scissors. Tool Holder...

... your printers screen annoying I have the solution for you. ...The cover fits easily into the screen casing and blocks the light coming from it. It's has a simple design that is quick and easy to print in pretty much all materials. Category: 3D Printing

... Hotend cover to accommodate 2 40x20 fans using the original support (plastic with the nozzle) for cooling the filament. Still in development to improve some minor points and the design but it still fits very well and without modification. ...

... Hotend cover to accommodate 2 40x20 fans using the original support (plastic with the nozzle) for cooling the filament. ...Still in development to improve some minor points and the design but it still fits very well and without modification.

... accessibility. To secure the tab, simply apply super glue or 3D Gloop with precision. An updated version boasts 10mm sides, providing an added layer of protection by concealing the bottom of the screen when a separate bottom cover is not available.

... common problem. The innovative cover fits seamlessly into the screen casing and effectively blocks out the offending light. ... Its sleek design makes it quick to print in a wide range of materials, ensuring that everyone can enjoy its benefits.

It fits all Ender3 alike screens also if it has a cover on the back. The frame that goes around the screen hooks onto the screenknob and to the back end of the screen. The print requires supports. I advise printing it in a dark colour, so...

It fits all Ender3 alike screens also if it has a cover on the back. The frame that goes around the screen hooks onto the screenknob and to the back end of the screen. The print requires supports. ... I advise printing it in a dark colour, so the...

To protect it from dust and dirt, the bottom of the panel is now covered. ...In addition to these modifications, USB holders have been added to the left side, while micro SD and standard SD card slots are positioned on the right for convenient storage...

However, I did notice one issue - I couldn't find a suitable cover for the original display. This is where this design comes in! This part prints flawlessly without supports. To ensure a smooth installation process, be sure to clear the screw holes...

Mainboard cover for use with 92mm fan. ... V2 corrected some spacing.

Anycubic Kossel Mainboard Cover Parts Needed: * M4 8mm Screw x 4 * M4 T-Nut x 4 Required Components: XT-60 Mount: https://www.thingiverse.com/thing:2771788 DC Power Socket Panel: https://www.thingiverse.com/thing:2764267

The Simple Anet A8 mainboard cover attaches securely by mounting it with the original screws, which are screwed directly into the printed feet. ...In my setup, the screws fit perfectly without any issues.

Here is the rewritten text: It's a Mainboard cover designed specifically for ANET A8 Printers, offering top-notch protection. ... This product is fully compatible with: Anet A8 Ultimate Frame Stabilizer - HEX REMIX ...

The mainboard fan on the Aquila is loud! I designed a new cover and am now using an 80mm 24V fan. I added another stl with thicker walls and a mount point - slide to get it to fit.These fit Aquila O1 and C2 (maybe others)As a side note: the...

This cover safeguards the K8400 mainboard, securing the fan and reset button in place. The relocated fan at the bottom panel's center boosts airflow significantly. To avoid accidental presses, the reset button is now positioned deeper inside. I...

This is a minimalist mainboard cover featuring open ends that form a tunnel-like structure, allowing the fan to function optimally. I previously designed a separate fan-holder (https://www.thingiverse.com/thing:900402), but with some adjustments,...

Crafted to shield the mainboard and conceal the wiring of the ANET A8 printer.

I design this cover to be mounted directly onto an Aluminum Profile 2020 or 2040, ensuring a secure fit with the Anet PK8.

I designed cover for my laser board box. ...There is place for 20mm fan, you can make adittional holes for fan bolts.

I swapped out the stepping motor drivers for the TMC2100 on the Raiscube A8R, which demanded a revised board cover. The existing cover's cooling was woefully inadequate, so I crafted my own custom solution. ...The lower Part2 is threaded with M3 screws...

You can use four M4 bolts to secure this cover to the printer. ...I would recommend you tap the holes first, since this is the stronger compared to letting the bolts tap the metal.SupportIf you'd like to support me for the 3D models I distribute for...