ender 3 linear rods 3d models

Even after putting the offset bracket all the way back and removing the lever from the switch my bed was still 4-5 mm short, so I've extended the bracket another 6mm (will reach the corner of the stepper motor)

My very first published remix. I moved the pully cable holders so the pulley cable fits. I found it impossible to fit the existing cable to the original design by badadz so I went about remixing it. I also added a horizontal cable holder on the...

Modified from https://www.thingiverse.com/thing:4627011 Parts Required 2x MGN12H sliding block 2x MGN12 rail 300mm 4x M3 T-nut for aluminum profile 2020 8x M3 6mm screw 4X M5 30MM screw(use the stock)

Made a change to the design to take remove mass, keep the build plate at the same height, and make it work with MGN12H and MGN12C rails. ...Uses M5x5.8mm, OD7.1mm thread inserts and 300mm rails

Print at 100% infill. You will want to install the stock bed carriage without the wheels on to these blocks. ...Keep all the bolts loose and then tighten them incrementally while sliding the bed fore and aft to ensure proper alignment and free motion.

This a remixed limit switch holder since the original limit switch adapter didn't fit at all. There was just no space for it. It bolts onto the extrusion with the motor mount and screws. ...No additional hardware is needed.

This will need to be printed with the plate front face down, and the BL Touch, and fan printed flat. Also these will need M3 hardware to be installed. I'm working on using heat inserts for the BL touch, as only 1 screw goes in. ... I will work on...

Made the webcam arm a bit stiffer as it was wobbling quite a bit at higher speeds and adapted the endstop mount to accept the arm. ...

This is a remix where the bottom holes are spaced to match the bed, the Standard Ender3 has a 2020 extrusion, and the original part was made for the 2040. ... I use the pre-cut holes in the bed (newer version, the "square-aligned wheels" one)

I remixed the drill guide and moved the rail block mounting holes to avoid the mounting posts for the sprite extruder. ... Also redid the belt adapter to fit the standard sprite extruder pro mounting bracket.

I changed the belt mount slightly to give a little more clearance for the belt. I have new belts which are crimped with zip ties and I found that it rubbed slightly for whatever reason as it left the belt mount. ... This replaces the...

Remixed Into Thicker Belt Clamps.

My very first published remix. I moved the pully cable holders so the pulley cable fits. I found it impossible to fit the existing cable to the original design by badadz so I went about remixing it. I also added a horizontal cable holder on the side...

This is a remix where the bottom holes are spaced to match the bed, the Standard Ender3 has a 2020 extrusion, and the original part was made for the 2040. ... I use the pre-cut holes in the bed (newer version, the "square-aligned wheels" one)

Vidéo ici / Video here : https://youtu.be/sLb9j2F7Rmk Remixes from 3849539 & 4670659 (remix search not working when posting this)

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/c273Eg0x76w

needed a custom extruder motor mount since the one I had would no longer work with new set up. ... This uses 2- M3x6x5 brass inserts and tree supports printed in PETG.

... bracket over the bed and rod, notice the thick side schould be pointing down or it wont fit ! next , grease your rods with thick grease and let the bed go all the way up and down letting the foam soaking it all in and spreading it over the rods

----NOTE UPDATE--- 13-4-22 1.2 Y-axis linear supports are corrected to avoid some errors with end-of-stroke detection in some versions of Ender 6 14-11-21 1.1 - Corrected an error in uploading the files for the Y-axis linear support as they were...

This is a linear rail mount for the X axis of the Creality Ender 5 with a Micro Swiss Driect Drive kit. The linear rail used is a MGN12H, 300mm The advantages of this design vs the others are * You don't lose X/Y space * Compatible with HeroMe You...

Ender 5 or Ender5plus Linear Guide update. Linear Guide I test With MGN12H-450MM The Design process adds simplicity in mind and use all the stock parts and try do not to change the 0,0,0 origin. You can print all the parts with no support, for mine...

Modded Versions of the following: Hydra Fan Duct: https://www.thingiverse.com/thing:4062242 Ender 5 Linear Rail: https://www.thingiverse.com/thing:3782865 Ender 6 linear rail mod: https://www.thingiverse.com/thing:4757747 This works for both BMG...

Modded Versions of the following: Hydra Fan Duct: https://www.thingiverse.com/thing:4062242 Ender 5 Linear Rail: https://www.thingiverse.com/thing:3782865 Ender 6 linear rail mod: https://www.thingiverse.com/thing:4757747 This works for both BMG...

When installing the Linear_Rail_Adapter, apply a few drops of epoxy into the screw holes for added stability. The M4 bolts will keep it snug, but with all the movement, you don't want it to come loose. You can still remove it later, but it will...

Necessary Additional Parts: Bondtech BMG or Clone:...

This mod mounts linear rails on the outside of the frame yeilding a bit more travel which pairs well with a bed upgrade. I prefer these heavy 15mm rails for the ender 5x to match the rest of the overbuilt machine. ... 2x MGN15C X 400mm 12x t nuts ...