ender 3 linear rail 3d models

Print at 100% infill. You will want to install the stock bed carriage without the wheels on to these blocks. ...Keep all the bolts loose and then tighten them incrementally while sliding the bed fore and aft to ensure proper alignment and free motion.

needed a custom extruder motor mount since the one I had would no longer work with new set up. ... This uses 2- M3x6x5 brass inserts and tree supports printed in PETG.

An upgrade to fix the not linear Y Axis extruded bar

3d printable parts to upgrade ender 3 x axis with 250mm ball bearing linear rail and improved duct. Compact design with cable management groove, 40mm fans housing and bl-touch bracket. Perfect to have a clean setup with an accurate and sturdy x...

https://www.thingiverse.com/thing:4976865 This remix will allow seamless integration with the following upgrades to you Ender 3 (V1, V2 & Pro) as well as Voxelab Aquila. 1. Linear Rail X-Axis (300mm in length MGN12-H Linear Rail) 2. Bltouch 3. ...

The mount on my Ender 5 w/ a Mosquito Magnum, MDD 1.3, and linear rails was not stable enough. I was getting some bouncing. I could not use a gantry clip because the rails were in the way. I added one more mount point that uses the screw that...

... 5 3 x 20mm bolts and self locking nuts, 2 4 x 25 mm bolts and nuts, and a 5 mm nut. ... I printed in eSun PLA+ 0.6 nozzle 100% infill the two linear rail supports, Spectrum petg the hot end adapter. I've added a little support to hold the wiring. ...

... use a very tight/high quality rail for Y. This allows the use of the blue annodized carriage direct onto 2x 300mm 12H linear rails. Edit - more elaborate V2 added. ...Adds some holes for self tappers to increase stiffness, as well as some ribs.

This is a fixed version as the original clashed. ...I could not edit that "Thing" so made another. See a photo of it in use on my Ender Pro with 2x MGH12 Rails.

This is a remix of Bryan Vines (BV3D) 3D Fused X Gantry Alignment Guide for the Ender 3. The new rails sold by 3DFused are 350mm long, whereas earlier versions were 400mm. As a result, Bryan's original rail hanger design will no longer be...

This remix is a reworking of Bryan Vines (BV3D) 3D Fused X Gantry Alignment Guide for the Ender 3. The new rails sold by 3DFused are 350mm long. The earlier versions were 400mm, so the rail hanger Bryan originally made will no longer be compatible...

I didn't like any of the other Hemera mounts and needed something that fit on linear rails and had EZABL support. The other issue is the JST connection for the thermistor is pretty close to the mount, so I had to offset it to give it room without...

This mod is for adding a linear rail to the Creality Ender 3. I have these versions installed on my machine, and they are working well. Is this a necessary mod? Probably not. The Ender 3 is a well-built machine as it is. It's something that you can...

**Parts List** The guide includes a list of parts needed for the upgrade, including: * Rails (2 x 350mm mgn12 Linear Rails with mgn12H blocks) * Hex Socket Cap Screws (24 x M3x8mm) * T-Nuts (24 x M3) * Left Side components (4 x M3x6mm screws, etc.)...

Remixed a MGN9H Direct Drive linear rail mod (https://www.thingiverse.com/thing:5269344) to accomodate my MGN12C, as it was the one I've bought.I've dug the inner screw holes (the ones on the extruder side) myself with a drill bit as I didnt want to...

I remixed the drill guide and moved the rail block mounting holes to avoid the mounting posts for the sprite extruder. ... Also redid the belt adapter to fit the standard sprite extruder pro mounting bracket.

A corrected version of the original model. The STL model size has been corrected. ... The mesh resolution has been reduced without loosing quality

used the original as a blueprint mostly for size and hole position and added a spot to mount bl/cr touch, the precise one should fit titan hotend/extruder perfectly and have touch at optimal height to probe and be out of the way when printing, i have...

I extended the length of my M3 bolts just enough for them to reach the lowest point of those components, and then I made some adjustments so that M3 nuts could be securely fastened into place. ...My M3 bolts threaded partially into each part, but I...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/c273Eg0x76w

Ender 3 V2 Y-Axis Linear Rail Bed Carrier Mounts No Drill - this is a remix on one side of someone else's mount that are very very good but left out the Endstop Paddle. Print one of each top side down on the bed. I looked high and low, these are the...

this part X-Axis Limit switch for Linear Rail. You can use standart ender nut. ... I remix from https://www.thingiverse.com/thing:3562454, thanks alot.

I didn't care for most others' designs of the X-Axis limit switch when modifying my Ender 3 with a linear rail. The original X-Axis limit cover needed to be reworked, so I created a mod that offsets it 9mm to compensate for the width of the rail and...

Linear Rail X-Axis Conversion CR10/CR10s/Ender 3 MGN12 Print with Supports Attention! You must reverse the polarity of your x-axis stepper motor, or reconfigure Marlin's Configuration.h file to: #define INVERT_X_DIR true Additionally, verify that...

If you're interested in a similar linear rail setup, I recommend checking out Ivertech's Linear Rail design for the Ender 3 - https://www.thingiverse.com/thing:3194796/makes, along with their hotend mount, which is what I eventually switched to since...

This is a conversion for the Ender 3V2 to fit the Voron Stealthburner as a direct drive setup with the BL-Touch. BOM: Belt part: 4 x M3 heat insert 4 x M3x8 BHCS Bltouch part: 2 x M3 heat insert 2 x M3x6 BHCS Stealthburner part: 6 x M3...

This mount is designed specifically for the BLV Ender 3 Pro upgrade that utilizes an Hiwin MGN 12H linear rail on the x-axis. The design emphasizes the mechanical strength of the entire assembly: - It reuses the x-axis belt bracket provided with...

I have a Ender 3 v2 and made modifications to fit it. -Remix with an 18mm probe mount attached to the right side. -Different cable management with with a slim x chain cable mount attached behind the bracket together with the hemera (using three...

Creality Ender 3 Pro X MGN12H 300mm Linear Rail No Mods Light Simple Fast single y bearing support Easy to print, suggested PETG No modifications required but just to adjust Y endstop 3mm forward and a proper leveling Fists standard or Micro Swiss...