ender 3 linear rail 3d models

Made a change to the design to take remove mass, keep the build plate at the same height, and make it work with MGN12H and MGN12C rails. ...Uses M5x5.8mm, OD7.1mm thread inserts and 300mm rails

Simple endstop switch mount for ender 3 with linear rail conversion

I remixed this for my Ender 3 Pro with x, y, and z linear rails. I modified the cutout in the middle because there is more depth to use under the y-axis with the y-axis linear rails. ...I also used a 0.6 nozzle to print 0.4 lines because the extrusion...

... to The Ender 3 you need to swap the outer screw holding the Z-Stent to the original extrusion for a 30mm M4 Screw. The Part is Designed so you can melt a threaded insert in it and screw the Tensioner the Linear-rail-Plate and the Z-Stent together.

Put the adapters on the linear rails with (4) 3 mm screws. Center plate on adapters. Make from below for holes. Then drill out holes and mount plate on adapters. The belt adapters mount flush to the edge and drill holes and mount them. Belts...

This is a remix of the x axis plate for MGN12 linear rail mod by BobbleJot (Thing:3489410).\r\nhttps://www.thingiverse.com/thing:3489410/\r\n\r\nI had a problem attaching the hotend to the plate, just like others who have used this...

My take on a switching hotend design. I designed this to take two standart creality hotends, a servo (I used:...

I designed this to take two standart creality hotends, a servo (I used:...

<p>Print at 100% infill. You will want to install the stock bed carriage without the wheels on to these blocks. ...Keep all the bolts loose and then tighten them incrementally while sliding the bed fore and aft to ensure proper alignment and free...

I've joined both the plate adapter and the belt tensioner. It's suggested to add a modifier to make the part around the holes solid, or after a while the PLA will sag & let go, and the bolts will loosen making the whole bed unstable on the Z axis...

Remix of Ender 3 S1/Sprite Pro Linear Rail Mount by bilbs84 with belt slots spaced out 10mm for compatibility with Ender 3 v2

I recently ordered a Linear rail kit from Creality for my Original Ender 3 and to my surprise the Linear rail was not the usual 20x20 pattern but rather a 14x20. ...I remixed the holes in tinkercad for original authors adapter to fit my rail.

This kit will convert the V channel on the Ender 3 Belt X axis to a 12mm X 300mm Linear rail. Carriage Plate V2 aligns the belts to the pulley diameters. ...

I needed a carriage plate adapter for an MGN9 linear rail mod on my Ender 3. While the original was a good starting point, I wanted to be able to add heat set inserts for adding and removing the hotend mount that I use (HeroMe Gen 5). I also needed...

**This is a work in process - parts are usable in current state** Included parts to upgrade your Ender 3 Pro from the POM wheels to linear rails on the Y-Axis. No more adjusting eccentric nuts under your bed! Compatible with MGN12H Linear Rails The...

I wasn't satisfied with the side mounted linear rail designs shown on most Ender 3's. Here is my design of a top mounted linear rail with 3D printable brackets. Below are links to the parts I used. I used M3 hardware for this entire build. ...

This is a test to convert the Y axis of my Ender 3 Pro to linear rail. For this, I used two MGN12H 300mm Linear Rails, some screws, and a small amount of ASA filament. To fit the linear rails correctly, I made a tool:...

The carriage is a bit thicker than normal so you can use the hartk pcb without damaging your connector by bumping into the frame.&nbsp;Parts you need:&nbsp;1x 300mm MGN12H Linear Rail12x M3 Hexnut (Nut Carrier)&nbsp;12x M3x10 SHCS (For mounting the...

To replicate this mod, you'll require three 12mm linear rails, along with various M3 'T' nuts and bolts; however, most parts serve as spacers, so feel free to reuse existing items where possible. A key aspect of this modification is that it doesn't...

You'll require two RA brackets and three small bracing plates to install a single 2020 V-slot linear rail support on an Ender-3 or any printer that utilizes V-slot extrusions.

I finally decided to get a couple of cheap linear rails with double carriages. This Connector will fit the MGN12B(?) carriage profile. The only modification was to the aluminum plate that the Connector is attached. I abandoned the existing holes and...

This adaptable mount is designed for seamless integration with your existing setup and also provides a future-proof solution, empowering you to effortlessly upgrade to linear rails whenever you're ready. ...Simply adhere to the original instructions...

I designed this in OnShape to help with the installation of a Z-axis Linear Rail kit I purchases on Aliexpress. ... I spent far too long tweaking the z-axis rails and wanted a faster way to make sure everything was well aligned.

I remixed the Drill Guide for my Ender 3 Y Axis Plate, which is the newer non-pro version. Thanks to bobblejot for the awesome original design. Visit bobblejot's original design for the other parts of this mod. **Update: January 10, 2019** I added...

Stock Y axis on Ender 3 has problems, soft aluminum plate makes wheel alignment challenging. Wheel spacers dig in, causing wheels to bow. Even when wheels work well, I still don't like them for Y beds. This fix addresses that. Re-used existing bed...

Remove the wheels, and bolts, then fit the adaptor to the linear rail carriage using 4 M3x8mm screws. Secure the original mounting plate to the adaptor, using 2 M4x10 bolts & nuts, and one M4x16. You're now ready to refit the extruder, bed probe,...

Remix from an awesome design made by ThijsOudeVrielink (https://www.thingiverse.com/thing:3432489) The original had the right-side hole in a position that would not work for the MicroSwiss Linear rail bracket. I just moved it over slightly and added...

This is a new carriage I designed for the bed of my Ender 3 Max, the first mounts I designed resulted a bit too flimsy so I wanted to try a mount that was designed all in one piece.

https://store.micro-swiss.com/collections/spare-parts/products/main-body-for-micro-swiss-direct-drive-extruder-for-linear-rail-system...

... bolts to m5x.80x16 bolts. added two holes toward the middle if you want to drill for even more stability (unnecessary) . Printing: 30% infill uses PLA. the ender 3 max is insulated - i also have pla on my regular ender 3 - no issues.