ender 3 linear rail mod 3d models

This is an x-carriage for the Voron Stealthburner on a top mounted linear rail Ender 5/5+. You will need a new belt (longer) and a couple of these clips https://www.thingiverse.com/thing:2814851I remixed this off the rail mod as I think that's how...

I was about to upgrade my hotend and extruder with dde kit and also go for axis to linear rail than research a bit lots of people complain about they loose z height so I design a part that re-align the upper bar which both relieves the stress on...

Remix of KerseyFabrications Ender 5 Linear Rails Mod . I switched the orientation of the rails so that they did not impact the belts. I also remixed Ender 5 X and Y Axis Endstop re-orientation by rmpel and TH3D EZABL Mount with Cable Guide/Strain...

Screw the linear rail to the two printed rail guides using M3 8 mm screws, but leave about 3 mm gap between the rail and the guides. 3) Remove the acrylic side panel, unscrew and remove the wheels. The X axis extrusion will be held in place by belts...

I wanted to design my own hot end for my printer so I looked everywhere for a STL file of the 3dfused direct drive plate for my ender 3 pro. Was nowhere to be found. There was one here on thingiverse but the model dimensions didn't line up with what...

3d printable parts to upgrade ender 3 x axis with 250mm ball bearing linear rail and improved duct. Compact design with cable management groove, 40mm fans housing and bl-touch bracket. Perfect to have a clean setup with an accurate and sturdy x...

Use them to space the linear rails from the top 2020 extrusion. This is designed to be used with direct drive. I am using a Biqu H2 extruder but it will work with others obviously. You must print at 100% infill. I used 0.2 layer height. This set up...

You Need: for X-Linear Rail ----------------------------------------- 1x MGN12H 400mm Linear Rail 8x M3x8 cylinder-head-screw 8x M3 drop-in-t-nut for X-Endswitch ------------------------------------------- 1x M3x16 cylinder-head-screw for Hermes...

Ender 3 V2 Y-Axis Linear Rail Bed Carrier Mounts No Drill - this is a remix on one side of someone else's mount that are very very good but left out the Endstop Paddle. Print one of each top side down on the bed. I looked high and low, these are the...

They are not part of the mod, but just a tool to use to keep the linear rail centered on the extrusion. They can also be used to help keep the Carriage Blocks from sliding off the Rail. Parts needed: 2 @ MGN12 Linear Rails. 300mm to 350mm in length....

Hey guys, for this mod for "Full Bear MK3s" you will need the following things: 2x IGUS TS-04-12 (linear rail) with a length of 370mm 3x IGUS TWE-04-12 (linear rail carriage with adjustable play) (optional) 2020 aluminium extrusions with a length of...

This is a remix of three parts to fit the EVA2 carriage (for different extruders and hotends) to an Ender 3, Ender 3V2 or Ender clone with x-axis linear rail installed in front of the 20x20 extrusion profile. Standard EVA2.3.0 only works with...

And the rail carriage's proximity to the barrel will likely prevent the use of an “in shroud” pcar/scar.Hardware needed:For RailQTY:  1...MGN9H or MGN9C 150mm Linear RailQTY:  8...M3x8mm Socket Head ScrewsQTY:  8...M3 Hex NutsFor PumpQTY:  4...#6-32...

This mod is designed for the Adimlab Gantry Y axis linear rail system. Part requirements include two MGN12-450 units plus an MGN12H. The user must print a linear rail support as shown and a mirror image of it. Eight M3-6 countersunk screws are...

X Endstop for Creality Ender 3 / CR-7 made to fit with mgn12 linear rail

Y Endstop for Creality Ender 3 / CR-7 made to fit with mgn12 linear rail

I've designed a custom plate to mount a pair of THK 15 linear rails along the Y-axis, paired with a modified wheel that interacts with the original endstop.

To be honest, none of the existing linear rail mods for the Y axis impressed me. When upgrading my Tarantula, I considered using a wider rail - specifically an MGW 15 for the Y carriage. The block itself is wider and likely more stable than the...

To build this mod, you'll need: - Two 500 mm MGN12H rails and two MGN12H blocks http://s.click.aliexpress.com/e/FRtpNpfK - Eight M3x8 screws for the MGN12H blocks and approximately eight more M3x8 screws http://s.click.aliexpress.com/e/2B6eKbYy - M3...

Here are the parts needed to convert the Kingroon KP3 X Axis from a 20x20 V Slot Rail to a Precision Linear Rail system like the one used on the Y Axis: These components allow you to remove the V Slot Rail entirely and replace it with an affordable...

There are many linear rail designs for Ender 3, but this is the best design that accomodates all the features I want. 1. top mounted single linear rail 2. belt tensioner 3. minimal bed modding (4 holes on top for the carriage), you can find a...

Infact, printing a 0.3 first layer and 0.2 the others, I had last layer missing and so a gap. So, check the preview of slicer before print. I had to drill the 4 holes of metal supports with a 6mm tip, to have a little bit of "play" You need 2x 500mm...

I've created a modification for converting the Y-Axis of the Artillery X1 into linear rails, significantly improving its performance and reliability. Two pieces of THK RSH12ZM 450mm rails are used, along with two bearing blocks on one side and one...

This file is designed for Adimlab's 3D printer, a 310x310 Z linear rail MGN12 setup with a 500mm long track and MGN12H carriage block intended to replace the existing rollers on the z-axis. Additionally, the motor attachment plate has been...

Update www.thingiverse.com/thing:3247870 This is my take on linear rails for the X5s. These are designed for 9mm tall GT2 idlers for a 6mm belt (factory size). You can use anything you want that fits a 9mm gap, though. I included one x carriage with...

Anycubic Predator NX (Linear Rail modification) model ========================================== Description --------------- This is a full CAD design of my modified Anycubic Predator with linear rails. All essential measurements are accurate to...

I modified it a little because of the linear rail's constraints. I added a bottom fan since I use a foot that elevates the printer. The box was designed specifically for M3 inserts. ... Fan dust filter:...

Next, apply the 2 guides to their designated spots, loosen the screws holding the 2 long Y 2020 bars in place, position the bed with the printed guides securely attached, slide the bed until it perfectly aligns with the 2 long Y 2020 bars, tighten...

Remixed from: https://www.thingiverse.com/thing:3676494 I had to modify it a little because of the linear rail. I have also added a bottom fan since a use a feet that lifts the printer. The box was designed for M3 inserts. ... Fan dust...