ender 3 lcd 3d models

This is a slight modification of https://www.thingiverse.com/thing:4586351 ! This model lowers the IO holes and standoffs for the Raspberry Pi 4. I needed this to fit a small extra component inside the enclosure. I've printed this and the Pi still...

This is a basic LCD cover designed specifically for the Ender 3, its primary function being to shield the display from producing an overly bright light that might disturb individuals who have their printer situated in a bedroom and plan to leave it...

A Simple Ender Series LCD Cover Requires No Additional Supports or Glue. Print the cover in the orientation depicted in the image provided. You can choose to print this design as a single piece, but I personally prefer splitting it into two...

I printed mine on ender3 This is a complete mount solution to replace the Ender 3 (or any other printer running octoprint with a pi) LCD with a 7 inch color touch screen display connected to the raspberry pi. I used this 35$ cheap clone display from...

snap on LCD case for ender 3 with alterra logo. ... check https://www.thingiverse.com/thing:3670360 for compatibility and information as this is NOT made by me, i only added a alterra logo on there Alterra logo used from:...

Please use v042 for Raspberry Pi 2/3** This is an enclosure that I designed to go under the LCD display of the Creality Ender 3 Pro (probably will fit perfectly to Ender 3 too) that also holds a Raspberry Pi 2/3 and now 4. ~~Later on, upon request,...

This includes a cut out for the 4040 Damper legs in the front Right corner for the Ender 3 Printer.

...... It is made to include an SSD drive with Inland SSD USB 3 adapter along the back. Not perfect as there is an opening in the from of about a 1/4 square as the framework for the screen does not cover it. May print a little small plug to clean it up.

Case for Ender 3 S1/S1 Pro probably 3 V2 as well This is intended to use with: [Waveshare 5 inch DSI LCD display](https://www.waveshare.com/wiki/5inch_DSI_LCD) It has an opening for a 4010 fan and also opening for GPIO pins The back cover slides into...

This is a remix of an awesome LCD cover for the Ender 5 that incorporates a Raspberry Pi case into its back panel.\r\n\r\nI've remixed it to rotate the case 90 degrees - this way, the USB and Network ports are on the bottom of the LCD cover when it's...

You will need to increase the wall number for this to work properly because it has a lot of individual pieces. ...This will be hard to print if your build plate adhesion isn't great

No need to change anything in print settings, just download, upload and print. ... Works really well.

Here is a rewritten version of the text: Custom LCD and Control Knob for Creality Ender 3, Ender 3 Pro, and CR-10 Models. ... Remixed from Original Designs by Guppyk (Thingiverse: #4204606) and Inuit (Thingiverse: #3611103).

Loved the Winged LCD Knobs but felt all the ones I tried didn't fit the way they needed. Hope this helps you spin to those numbers fast, with a tight locking spin and a nice click!

+Test calibration cube 20x20x20 mm: https://www.thingiverse.com/thing:3162872 ------------------------------------------------------------------------------------------------------------------------ Level Procedure / Procedimiento Nivelado: We made...

A simple mount to allow using the BigTreeTech PITFT43 LCD screen with a Raspberry Pi board attached on back on an Ender 3 S1 Pro. This mount will block the hard wired NIC port and you will need to flip the screen orientation. More Ender 3 S1 models...

This simple adapter is designed to fit bigger buck converters, including those with an LCD display, inside the all-in-one rear electronics case from Teaching Tech. ...It replaces two relay slots on the right-hand side of the case and requires no...

The case not only protects the LCD display, but also has a Raspberry Pi mounting. There is also the possibility to install a fan. The connectors of the Raspberry are also added, so nothing has to be cut or drilled. The LCD display cable can be...

The Creality Bltouch kit LCD adapter was in the way of the stock fan and the lid wont close, so i just move the fan holes a bit to the back and remove the hole for Z stop cables (is not needed because de bltouch). All credit goes to fefede. ... sorry...

The Creality BlTouch kit LCD adapter was getting in the way of the stock fan and the lid couldn't close properly. I simply adjusted the fan holes a bit towards the back and removed the hole for Z stop cables since the BlTouch doesn't need them. All...

I copied the 25mm fan from https://www.thingiverse.com/thing:4176051 to https://www.thingiverse.com/thing:4712893 and cut the ends off like in https://www.thingiverse.com/thing:4993078

Ender 3 to skr v1.4 mod Main features: e3d V6 hotend BMG type direct extruder Prusa 2004 LCD TMC2208 drv light heated bed H carriage Marlin 2.0.3: Nozzle Park Advance Pause Linear Advance Optimized acceleration, jerks (juntion derivation), feedrates,...

Ender 3 Skr V1.4 Mod Main Features: Creality E3D v6 Hotend Upgrade BMG Type Direct Extruder Installation Prusa i3 LCD Display with 2004 Controller TMC2208 Stepper Driver Integration Light Heated Bed and H-Carriage Upgrade Marlin Firmware 2.0.3:...

<p>N’hésitez pas à partager vos fabrications.</p>

Pour l'ajout d'un mini 12864 MKS sur carte mere MKS. Pour les nappes partir sur des modèles IDC 10 pôles de 50cm de long. Connexion : Carte mère EXP1 > Écran EXP 1 Carte mère EXP2 > Écran EXP 2 Pour la configuration dans marlin, voici le tuto :...

N’hésitez pas à partager vos fabrications.

Adding a mini 12864 MKS to the mother board MKS. To create the wiring for the PCBs, start with IDC 10-pin models 50cm long. Connection: EXP1 Motherboard > EXP1 Screen EXP2 Motherboard > EXP2 Screen For Marlin configuration, see this tutorial:...

I have taken the original idea from https://www.thingiverse.com/thing:4584686 and redesigned it with Fusion 360. This has been built from scratch and only using the concept. The cover allows for the use of the fitted draws:...

Includes a DB9 (serial) port for adding a macro keyboard. See my matching Macro Keyboard at: https://www.thingiverse.com/thing:5039904 Serial Cable used:...

This remix makes it possible to mount your Pi on the right side of your Ender 3 v2 (maybe Ender 3 as well). Most people seem to mount their pi on the left side of their printer, but this takes up a lot of space. There's space behind the LCD, but...