ender 3 lcd 3d models

... any need for support material. Print the BOTTOM right side up. I used 4 M3x5 screws to secure the Pi to the base. Predrill your holes to make it easier.I used the stock mount screws for the LCD (M3x6 I think) so predrill those holes also. ...  

I had identical issues with some of the others where the screw holes refused to cooperate with factory screws, only getting clogged up, I'm not sure if Cura's settings were at fault or what caused this problem so after five failed prints I decided to...

Layer height 0,28mmInfill 100% !!!Compatible with accelerator MPU-6050/GY-521 (demand mechanical and electrical interference in LCD board)

<p>This is a remix from the V2 0mm Clearence and have an extra stl to print. ...This two bars mirrors the original mount to add firmness to the LCD.The way its to print in separate parts and superglue it in place.

Design this because when you made an autohome the screen cover had to be closed. ... I leave two versions, one in case you want to put screws in the guide and another without screws (is the one I use, it stays very strong without vibrations) ...

[DEPRECIATED] A new version is in the works with better accuracy measured it best I could and flipped it ~ and stretched it Printed and functional v3 because v1 wasn't long enough and v2 wasn't wide enough to fit the screen v3 is a little too wide...

measured it best I could and flipped it ~ and stretched it Printed and functional v3 because v1 wasn't long enough and v2 wasn't wide enough to fit the screen v3 is a little too wide but it is functional This is V3 I lost v1 and v2 wasn't...

Design this because when you made an autohome the screen cover had to be closed. I leave two versions, one in case you want to put screws in the guide and another without screws (is the one I use, it stays very strong without vibrations) Anything,...

It is, however, very heavily inspired by Tronnic's beautiful Ender 3 Touchscreen Case & Holder for Raspberry Pi. I have printed several copies of Tronnic's and other remixes, all without success because my Waveshare screen hates all of these cases. I...

<p>Found this remix of a remix of a remix and I turned it into yet another remix :)</p> <p>I liked CommGuy's remix in removing the hole for the switch but wanted to get rid of the power supply screw down area as I want that bit of extra length from...

Found this remix of a remix of a remix and I turned it into yet another remix :) I liked CommGuy's remix in removing the hole for the switch but wanted to get rid of the power supply screw down area as I want that bit of extra length from the...

This bracket will help reduce glare and allow better visibility from a standing or seated position.

I wanted a mounted display for my lack enclosure, but I didn't want it to stick out. This display stand allows you to slide it in and out. I recommend sanding the slides with 100 grit sandpaper, then 300-500 grit. This will help it glide a bit...

I was in need of a mounted display for my acrylic case, but I didn't want it to stick out prominently. This display stand gives me the flexibility to slide it in and pull it out at will. ... I highly recommend sanding the slides with 100 grit sandpaper,...

YOU MUST TAKE CARE WITH THE OPEN LID AND DO AUTOHOME. I AM THINKING ABOUT IMPROVEMENT. You already have the solution to be able to use the cover without fear of breaking it when we do autohome https://www.thingiverse.com/thing:3622460 The hinge is...

This is a remix of https://www.thingiverse.com/thing:4725470 by FredrikA Update - I've uploaded version v2 which adds one support that eliminates the wobbling. --- I needed a mount that will fit my display below the camera that I had already...

YOU MUST TAKE CARE WITH THE OPEN LID AND DO AUTOHOME. I AM THINKING ABOUT IMPROVEMENT You already have the solution to be able to use the cover without fear of breaking it when we do autohome https://www.thingiverse.com/thing:3622460 The hinge is...

I've developed a customized solution for mounting an LCD 2004 display on the Ender 3, compatible with the SKR 1.3 board, as an alternative to using the Ender display if it's not functioning for you.\r\n\r\nIf my design proves useful, please consider...

Print these two designs on a sturdy material to conceal the LCD console and the exposed circuit board underneath it, specifically tailored for your Creality Ender 3 or Ender 3 Pro.

Modified version of paulhaines screen cover supports: https://www.thingiverse.com/thing:5363536/remixesMade to fit snugly on the ender 3 screen if you have this LCD PCB Cover on: https://www.thingiverse.com/thing:2858209Requires supports. ...Recommend...

Modified version of paulhaines screen cover: https://www.thingiverse.com/thing:5363536/remixesMade to fit snugly on the ender 3 screen if you have this LCD PCB Cover on: https://www.thingiverse.com/thing:2858209Requires supports. ...Recommend normal...

... it sits too low on my Ender 3 Pro's control knob shaft. When you pressed on the control knob, it would hit the top of the LCD cover. I raised the floor of the knob's shaft hole so that it sits higher on the Ender 3 Pro control shaft. ... Enjoy

I liked [Creality Ender 3 Pro - Raspberry Pi 2/3/4 + LCD Enclosure](https://www.thingiverse.com/thing:4586351) but I have an Ender 5 Pro so I took the file (v042 is what I modified) into [TinkerCad](https://www.tinkercad.com/) trimmed the front and...

This is a set of mounts for attaching a WAVESHARE 4.3inch DSI LCD Raspberry Pi touchscreen to a Creality Ender 7 3D printer. You can print this out of pretty much whatever you like. Uses the screws which come with the screen for mounting to the...

Realice este Remix debido a que moví el lcd a la parte superior del perfil y el modelo original hacia que el lcd quedara muy atrás y chocara con el perfil

Layer Height: 0.36 Initial Layer Height: 0.1 Infill Line Width: 0.6 Wall Thickness: 2.4 Wall Count: 4 Top/Bottom Thickness: 1.08 Top Thickness: 1.08 Top Layers: 3 Bottom Thickness: 1.08 Bottom Layers: 3 50% Infill Line Pattern 220 Nozzle 60 Bed 100...

I made this to cover my LCD screen figured other imperials out there might want one. If you like it please leave a like and share your prints. ...I printed it in pla as it really does not matter at .12 like I do my minis.

No need to change anything in print settings, just download, upload and print.&nbsp;Works really well!!!&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;*Old LCD Knob (Goodbye)&nbsp;

This is a basic LCD screen based on Terminator's Cyberdyne Systems company logo. Rather than a big hook, loop, or handle of some sort, I created a simple obscure notch to help get it up off the screen. It's really not even required. It's easy enough...