ender 3 laser head 3d models

This is a simple mount that allows to use the Ender-3 S1 Laser module without remonving the Sprite extruder. ... https://youtu.be/-a9nY-8EYfI

***Very Important Note*** When using the Laser output on the printer board, it appears to cause the laser to briefly light at full power on startup, when changing cards and when starting a print, maybe at other times too. ... Wear your glasses at all...

Laser Mount for the Ender 3 that makes it so you can keep your Laser and BLTouch mounted and print as you normally would using the stock hotend shroud.

Lens cover for Ender 3 laser engraver. You can cover the lens with this cap to avoid dust or debris entering the laser module and to prevent damages from accidental activation of the laser. External diameter of the laser lens adjustment ring:...

My Ender 3 laser kit came with a splitter cable but I couldn’t see the point of it. I’ve repurposed it into this switch to change between fan and laser. ... Houses a on/off/on DPDT switch 28mm x 21.5mm Printed in PLA, needs 2 x M5 T-nuts and 2 x short...

My Ender 3 laser kit came with a splitter cable but I couldn’t see the point of it. I’ve repurposed it into this switch to change between fan and laser. Houses a on/off/on DPDT switch 28mm x 21.5mm Printed in PLA, needs 2 x M5 T-nuts and 2 x...

Human: Easy removal support for the Ender-3 laser. Watch this YouTube video: https://youtu.be/1oyUh8zMWbE. First, place the lower section of the piece under the extruder block and then adjust the top to hear a distinct clicking sound. I've also...

I'm looking for a bracket specifically designed for an Ender 3 printer without any modifications. ...If you've created one, I'd appreciate it if you could share it with me!

I was tired of knocking my laser head off on my ender 3 so here is a mount that works with a go pro tightener. This can be changed out for any bolt of your choice. ...Happy printing/lasering

I was tired of knocking my laser head off on my ender 3 so here is a mount that works with a go pro tightener. This can be changed out for any bolt of your choice. ...Happy printing/lasering

This is a holder for the 0.5w laser module used with Ender 3. My laser module was constantly moving around when it was atached to the printing head only by the magnets because the cable is too stiff. With this, the module stays in position. ... The...

This is a holder for the 0.5w laser module used with Ender 3. My laser module was constantly moving around when it was atached to the printing head only by the magnets because the cable is too stiff. With this, the module stays in position. ... The...

Laser Stick to control the laser focus in more safety way. ... I Use and print it on my Ender 3 V2. ... Resolution print of 0.2

have fun ;) --- Da es keinen Halter für einen Laser gab den man direkt auf die Ender 3 / Ender 5 Hotend Platte schrauben kann, habe ich nun einen erstellt. Den Halter einfach auf den Laser schrauben, Hotend und Lüfter demontieren und den Laser auf...

I'm upgrading my Ender 3 printer with a touch of elegance. ...Printing with the letters laid out face down is just the beginning, as I take my 3D printing skills to the next level.

This holds the standard 500mw laser engraver on the Ender 3. It's compatible with BL touch and provides a bit of extra support and stability for mounting the laser. The laser still uses the magnets for attaching to the fan housing, but this mount...

My laser head mount design for Ender3. ...It can be simply screwed on using the original screws and the laser head can be inserted in. ...

This holder is designed to replace the hotend on the Ender 3 to hold the laser engraver D-B500F instead, which can be purchased here: https://www.creality3dofficial.com/products/creality-blue-violet-light?sca_ref=10788.CFDqhuwn3C The difficulty in...

You will need to print with supports, the current design suits standard Ender 3 V2 and also has a cutout for the mounting screw if you have a fang. (refer to .stl - photo shows V1 with smaller cutout) To use this simply lift the Z Axis to 120mm,...

I made this to mount the official Creality laser cutter/engraver to the front side of the print head. It should work with any 33mm square laser head. This blocks the fan, so you don't want to leave the laser in while doing any 3D printing. The hole...

I got tired of cleaning tape residue off my print bed after using the laser engraver mounted on my Ender 3 Pro. So I designed this handy peg tray system to hold things in place for laser work on top of the print bed. The tray is split in 4 to be...

This is a modified remix of mrfansworth. ...This one is a little wider for my sainsmart laser. ... Removed a few internal layers.

(Check the comments for pictures.) If your module's backside holes match those on the 10W laser, it should work seamlessly. I aimed to keep it uncomplicated. This design replaces the hotend by simply attaching it to the side or bowden extruder,...

Zum Anbringen der Halterung werden 2 M3 Schrauben benötigt. ...Falls der Laser locker sitzen sollte können die unteren Bohrungen zum fixieren verwendet werden. ... Support wird beim drucken benötigt Infill 20 - 25%

I have my Bltouch on the side, so I had to come up with something I can keep Bltouch, and also have the laser option. This is what I came up with. For some reason, it is upside down. Please print with the flat side touching the build plate for best...

Bracket for OEM Ender3 Fan Shroud Bolts on Common Laser Modules from Ebay Easily. It Fits Over the Fan Shroud, Securing with a Screw and Captive Nut that Tightens Down Firmly. ... Use Three 3mm Screws and One 3mm Nut (Captive) to Get Started.

Ender 3 Head cable mount

Tête R2D2 pour extrudeur ENDER 3 R2D2 head for ENDER 3 extrudeur

This is a remix of my Ender 3 head badge. ...By request.

Laser headlight module mounting for ender 3.