ender 3 laser cutter 3d models

For those of you with a laser cutter, I've included a "minimal" print version that relies on some hardware and has some assembly required, but this will get your camera mount made in 1 hour or less compared to the 9 hour print time (at 0.2 mm layer...

Ender 3 V2 mounting system to upgrade to dual quiet 4020 fans and mount a 500 mW laser. I could not find a system to upgrade fans for the V2 and use a laser with they system, so I created one. Parts needed: 2 x 4020 fans 1 x 500 mW laser...

This change allows the mounting of Creality Falcon laser mounting bracket without removing HeroMe Gen 7 cooling system.Change does require moving ABL to RIGHT side, (CR touch fits with ‘compact’ on right side)Shifts Ender 3 hotend X position to...

K40 Laser cutter fume exhaust to 80mm / 3" ducting. This should be mounted to 10mm Lexan sheet that will be cut to fit K40's fan mounts. ...Enjoy!

Simple holder to (temporary) mount a laser to your 3d printer. This ring goes around the ABL so it is fairly easy to add and remove again. In my case I use https://www.thingiverse.com/thing:2879555 as the mount for the inductive ABL sensor Laser I...

After removing the Ender hotend, screw this mount onto the X carriage, and slide the laser into it.Print with a 5mm brim to stop it from falling over during printing.Use two M3x8 screws to attach it to the X...

updated orginal design for Ender 3v2 and removed interference with roller screw and added second screw hole. ... similar design for Ender 3 after upgrading to direct extrusion.

After removing the Ender hotend, screw this mount onto the X carriage, and slide the laser into it.It is designed to print the way it is oriented. ...Print with a 5mm brim to stop it from falling over during printing.Use two M3x8 screws to attach it to...

Mount a K40 laser cutter fume exhaust system to an 80mm/3" duct, secured firmly to a 10mm Lexan sheet that has been precision-cut to perfectly match the K40's existing fan mounts for optimal performance.

Remixed this original laser mount to work with a larger 40mm laser (sovol 5w laser). ...Works as intended.

Basic assistance is available for standard Chinese lasers that use four magnets.

... the top of the laser housing to accommodate the device's position. The added feature is quite convenient! Additionally, you can find protective covers specifically designed for the laser head, helping prevent accidental exposure to the laser beam.

This add-on will not interfere with the end stops on the Ender and can be left on while printing normally (but maybe retract the knife then using the screw on top).For a more detailed manual including how to create copper circuits from KiCad to...

......This ring goes around the ABL so it is fairly easy to add and remove again. In my case I use https://www.thingiverse.com/thing:2879555 as the mount for the inductive ABL sensor Laser I used was from here: https://aliexpress.com/item/33019893763.html

**UPDATE June 11, 2020**: Added "Keith's Laser Mount Tweaked" which increased size of magnet holes to 13.4mm to also accommodate 1/2" magnets still works with 12mm as the epoxy will hold and fill around the sides fixed positioning of countersink for...

You'll likely need to expand the holes on Creality metal frames, as they vary slightly in dimension apparently. ... The laser sits 13 millimeters farther back from the nozzle in the Y-axis direction.

This is the first thing I have designed so it may be overly engineered but it works for me.I purchased the Creality 10W Laser module and as I have converted my printed to direct drive (using the Creality conversion kit) I could not use the original...

I designed this mount to hold a switch for switching between laser and fan so I don't need to open the case every time. The switch is mounted in a way that if something falls on top of it, it wil switch the fan on instead of the laser. The mount...

... again. In my setup, I utilize a mount designed specifically for inductive ABL sensors found on Thingiverse: https://www.thingiverse.com/thing:2879555 The laser I opted for comes from AliExpress: https://aliexpress.com/item/33019893763.html

... The model was drawn so that it could be entirely cut on a laser cutter/cnc mill, except for the propeller cone (which can be 3D printed) and the propeller shaft. ...All the laser-cut parts should be cut from 4mm plywood.Drawn in SolidWorks 2017.

... печати на пэтг 235/70. заполнение 50% поддержка 60" My name is Usman, this is my first model for this site. Use on health! Mount for the laser. Remove magnets before using fasteners. for printing on petg 235/70. ...filling 50% support 60"

Video: UPDATE 2: - Added Ultimaker 3 version UPDATE: - Added screw holes for huge ball bearing (see last image) - Added thermal exhaust ports on side panels for cooling and those damn rebels Few people are fortunate enough to have ample space behind...

If you want to fix sovol laser module on sovol sv02/ender 3/ender3 pro/ ender 5/ ender 5 pro, please download it. ... Sovol SV02: https://sovol3d.com/products/sovol-sv02-dual-extrusion-3d-printer Sovol laser...

Video 3: This video showcases the capabilities of Thingiverse, a platform that allows users to share and download 3D printing models. It's an essential resource for anyone interested in DIY 3D printing. ... You can find more videos like these on my...

Remix of "Ender 3 Hotend and BLTouch Cover" by mausic, which is a remix of "Ender 3 (and Pro Variant) Grill-less fan shroud for OEM Stock fans" by Samthegreat, which is a remix of "Ender 3 Pro Fan Shroud for 40x40x20 fan" by Thomebau.I made the...

This is my first upload to Thingiverse, feel free to remix this and use this in your own 3d printer

Check Out My Video On Converting An Ender 3 To A Vinyl Cutter / Plotter: Link: https://youtu.be/4XV9aHWMRFo Works in with Bl Touch Installed too. ... Design to hold vinyl cutter blade, commonly found on eBay.

Vinyl Cutter Tool (Drag Knife) Holder using [Creality Ender-3 S1 Simple Tool Changer](https://properprinting.pro/product/creality-ender3s1-simpletoolchanger/) by Jón Schone - https://properprinting.pro I found this great interchangeable tool system...

This is a variant of my Filament-Cutter for the SMuFF to be used on an Creality Ender-3 (or similar) equipped with an E3D-V6 hotend.STEP file only.**NEW VERSION**This new model has got improved cable routing/mounting.**UPDATED 2022-03-25**Added...

This is a variant of my Filament-Cutter for the SMuFF to be used on an Creality Ender-3 (or similar) equipped with an E3D-V6 hotend.STEP file only.**NEW VERSION**This new model has got improved cable routing/mounting.**UPDATED 2022-03-25**Added...