ender 3 glass bed install 3d models

Hey guys, This bed levelling design will check the four corners and the middle of the bed by printing squares and the best thing is it prints diagonally from middle square to the corner ones to check the bed adhesion. You can stop printing after the...

I loved markarsenic's bed handle at first, but when I swapped out the shorter springs for longer yellow ones, the handle's mounting bracket took up too much space on the bed screw. Luckily, I'm using 3Drcnc's camera mount which doesn't interfere with...

Extended this handle so that the finger hole was sticking out just past the front of the bed. Works very well and is a simple design. ...Thank you to the original maker!

More flexibility of the bed's foundation enables a steadiness of the setup. ...A set consisting of M6 by M6 bolts and six hex nuts, along with six washers that are 6 millimeters in diameter.

my take on a bed handle that bolts onto the plate under the build surface using the unused holes already there . ... i put a hole at the front for a camera in the future just a quick alteration to avoid the boltunderneath

I could not find the origional I started with but this had every part modified except the tab at the top The hole in the end for the bed spring is 16.3mm, its wide enough for the rubber spacers. ... The arm is flatter so it can print with less...

A handy grip makes moving the bed easier and prevents heat injuries, you know? Print it horizontally like the gray picture on this page. First, unscrew the knobs, place the handle in position, and then screw the knobs back onto it. ... There's a camera...

I got fed up with having to grab my bed while it was scorching hot or when I didn't have time for it to cool down completely. So, I searched Thingiverse for bed handles. Many other bed handles on the site didn't match the look I wanted or fit...

... with my Ender 3. ...To keep them organized, I've created and printed a storage rack. The holder is designed to hold four pieces of 4mm 235x235mm glass plates, which are commonly used with the Ender 3, Ender 3 Pro, Ender 5, and many other printers.

ender 3 glass bed frame to keep the glass center with bed wiring strain relief and spring guides integrated into the frame. the spring guides i used are these from this link https://www.thingiverse.com/thing:4078927 an ive ran these on top of the...

ender 3 glass bed frame to keep the glass center with bed wiring strain relief and spring guides integrated into the frame. the spring guides i used are these from this link https://www.thingiverse.com/thing:4078927 an ive ran these on top of the...

Remix to accommodate a 25mm radius glass bed holder without interference

Z stop spacer transitions seamlessly from Bed to a precise 3.2mm (1/8") thick glass or mirror, requiring no adjustments to the level. Slide the Z stop switch to the right when printing on bed to achieve perfect alignment. Add tape or lightly sand...

I modified the original file to take into consideration the glass bed as well as the m4 nuts and washer that some users employ to fasten the bed screws more securely. ... This modification enables you to keep the z-stop at its original position and...

I edited the original file to account for the glass bed as well as the m4 nuts and washer that some people use to secure the bed screws better. ... This should allow you to keep the z stop at the original point and account for all the additional...

Simple bed corner holder for Ender 3 V2. ...It is designed for the original glass bed.

I'm super stoked to share my very first Thingiverse creation with you all - a custom clam design that I just can't get enough of! I was on the hunt for the perfect clam, but couldn't find one that met my exacting standards, so I decided to take...

I've thoroughly tested these mirrors in place using a 4mm mirror, and I'm pleased to report that they hold up exceptionally well when printed at a 99% scale through Cura. ...The results are impressive, especially considering the material used is PTEG.

These clips work with a 165x165mm glass bed for the Adventurer 3. They are designed to wedge the glass in place on top of the heated metal plate, but not clamp the glass. After 4 iterations I believe these work to hold the glass without depressing...

After buying my Borosilicate glass bed, which measures 220x280x3.8, I was instructed to use bulldog clips, but I opted to create my own solution instead.

... this Project: - Clip Thickness Was Set to 3. - The Bed Thickness was Established at 3.1. - A Depth of 4 was Selected. - A Width of 10 Was Specified. - The Glass Thickness was Determined to be 3.9. ...- Nub Dimensions Were Measured to be .25 Units.

this model is designed to hold the glass bed of your ender 5 pro 3d printer in place.

Glass Bed Clip designed for side mounting for Ender 5. ...7.2mm space, sadly the corner one didnt fit near the bed cables so i created this one.

Glass Size: 165x165 x3 The same design as the other three 3D prints with a screw, this one is designed to lock the glass in place on the bed and prevent any movement. ... It has yet to be tested through printing, but based on its design, it's expected...

These are basic mounts for those who want to utilize a glass bed on their Crafbot3. To secure them to the glass, use nuts and bolts. It's recommended that you print these using PETG. I personally prefer applying double-sided tape to prevent slippage....

Ender 3 Fast Bed Leveling

;Begin Purge Line G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line ;End Purge Line . .. ......

... ;Begin Purge Line G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line ;End Purge Line . ..

Corner tabs that help align glass beds on the heat bed of an ender 3. ...Could work for other bed types as well.

These clips are modified from Ender 3 glass bed clips by ccrowder5 https://www.thingiverse.com/thing:3359256, I adapted these clips to have a thicker rear end so they wouldn't snap when slipping them onto the heatbed and glass top. Designed for a 4mm...