ender 3 glass bed clips thingiverse 3d models

These clips are specifically made for 50mm sections of LED foil strips and come in two sizes: one for the 50mm section itself and another for the 48mm section where soldering takes place, providing clearance for the solder pads. ... Printing these clips...

Just another bed level

Here is a bed handle for the Ender 3. This handle is easy to print and is not too thick to where your springs compress too much. There are two versions, a simple version and a Hesed version.</p><p>Both require minimal support. in the middle. I...

Thing is desinged to hold 4 pieces of 4mm 235x235mm glass beds (typical for ender 3, ender 3 pro, ender 5 and many others). Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 - 0.32 Infill: 20% Filament:...

... like the gray picture on this page. First, unscrew the knobs, place the handle in position, and then screw the knobs back onto it. There's a camera mount designed by Moclub available at this URL: https://www.thingiverse.com/thing:2987358

I replaced the bed screw with a reliable fitting hex nut. ...The original stock bed adjuster had stripped threads, so I created this replacement solution.

So, I searched Thingiverse for bed handles. Many other bed handles on the site didn't match the look I wanted or fit properly (the hotend kept hitting them). I decided to create one myself. This design is low enough that it no longer causes issues...

redone the locking tab to be square so prints easy on the bed flat. ... newb on tinkercad.

Here is a revised remix of https://www.thingiverse.com/thing:3181360 that seamlessly integrates with the customizer. To customize this design, set the length to match the exact distance between the cut marks on your LED strip. ...I have conveniently...

Hey guys, This bed levelling design will check the four corners and the middle of the bed by printing squares and the best thing is it prints diagonally from middle square to the corner ones to check the bed adhesion. You can stop printing after the...

I loved markarsenic's bed handle at first, but when I swapped out the shorter springs for longer yellow ones, the handle's mounting bracket took up too much space on the bed screw. Luckily, I'm using 3Drcnc's camera mount which doesn't interfere with...

Extended this handle so that the finger hole was sticking out just past the front of the bed. Works very well and is a simple design. ...Thank you to the original maker!

More flexibility of the bed's foundation enables a steadiness of the setup. ...A set consisting of M6 by M6 bolts and six hex nuts, along with six washers that are 6 millimeters in diameter.

I could not find the origional I started with but this had every part modified except the tab at the top The hole in the end for the bed spring is 16.3mm, its wide enough for the rubber spacers. ... The arm is flatter so it can print with less...

my take on a bed handle that bolts onto the plate under the build surface using the unused holes already there . ... i put a hole at the front for a camera in the future just a quick alteration to avoid the boltunderneath

Customized version of https://www.thingiverse.com/thing:538624 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=538624

Aillant pas trouver se que je voulais j'ai du m'inspiré du net dont celui ci que j'ai aimé : https://www.thingiverse.com/thing:4610075 de @RadekSlowik ( je vous invite a aller sur son profil thingiverse ) . donc j'ai fais beaucoup de modif , un...

After using it for 24 hours with paper clips to hold it down, I realized that the pressure from the clips was preventing the glass from remaining perfectly flat. I searched for some clips but did not find anything that fit the Anet A6 the way I...

... This clip enables you to utilize a 220 x 220 mm glass bed on the Ender 3. The actual physical bed size of an Ender 3 is 235 x 235, yet the print bed size remains at 220 x 220. ...220 x 220 glass beds can be found online for significantly less cost.

... with my Ender 3. ...To keep them organized, I've created and printed a storage rack. The holder is designed to hold four pieces of 4mm 235x235mm glass plates, which are commonly used with the Ender 3, Ender 3 Pro, Ender 5, and many other printers.

This mashup of [Ender 3 Cable Clip](https://www.thingiverse.com/thing:2949858) by saitrix and [Ender 3 Rail insert](https://www.thingiverse.com/thing:3328378) by tonysix00 keeps the bed heater cable out of harm's way on my Ender 3.\r\nIt is my very...

ender 3 glass bed frame to keep the glass center with bed wiring strain relief and spring guides integrated into the frame. the spring guides i used are these from this link https://www.thingiverse.com/thing:4078927 an ive ran these on top of the...

Remixed these clips that worked great on my bed to begin. Made the outer walls slightly larger so they wouldn't bend as much. Also, added a small spacer so the bed is evenly in the center. These work great but are a little harder to get on. ...They do...

ender 3 glass bed frame to keep the glass center with bed wiring strain relief and spring guides integrated into the frame. the spring guides i used are these from this link https://www.thingiverse.com/thing:4078927 an ive ran these on top of the...

The clips are shorter and thinner, designed to fit perfectly onto the included metal bed clips for stock Ender 3 machines. This ensures that exposed wiring under the bed remains safe from shorts caused by accidental contact. See photos for accurate...

Remix to accommodate a 25mm radius glass bed holder without interference

Z stop spacer transitions seamlessly from Bed to a precise 3.2mm (1/8") thick glass or mirror, requiring no adjustments to the level. Slide the Z stop switch to the right when printing on bed to achieve perfect alignment. Add tape or lightly sand...

**Project Instructions:** The Following Options Were Used to Customize this Project: - Clip Thickness Was Set to 3. - The Bed Thickness was Established at 3.1. - A Depth of 4 was Selected. - A Width of 10 Was Specified. - The Glass Thickness was...

I edited the original file to account for the glass bed as well as the m4 nuts and washer that some people use to secure the bed screws better. ... This should allow you to keep the z stop at the original point and account for all the additional...

Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=81343 Instructions Using the following options: depth = 12 bed_size = 6 glass_size = 3.8 clip_width = 4 handle_thickness = .3 length = 12