ender 3 filament spool holder 3d models

Simple spool extension for second spool holder if you have nowhere to place your second spool you are going to print with. Uses original spool holder. Support is only needed for the two notches on top of the part. Be sure to completely remove the...

Bracket to prevent excessive unrolling of filament on filler holder (https://www.thingiverse.com/thing:3020026). ...It also holds my printer tent roof.

Adapter designed specifically for the ICE spool on an Ender 3 printer.\r\n\r\nInterior diameter: 30.3mm\r\nExterior diameter: 52.9mm\r\nHeight of adapter: 10mm\r\n\r\nDon't be shy to share your printed creations!

I crafted this filament spool holder because I was dissatisfied with the way the original one consistently failed to center the spool around the rotation axis. It can be adjusted from 33 to 63mm. Printed with supports solely on the build plate,...

I made it stick out farther because I use a HatchBox filament on a larger roll so the original was too close to the printer. I added holes to reduce the amount of filament used. I also made a support column. ...It will hold the spool just fine...

Filament holder with bearings that utilizes the original bracket on Ender 3. You'll need a 16 cm long M8 threaded bar. 2 pieces of 608Z bearings. 2 pieces of M8 nylon lock nuts. And 2 M8 washers. For the "Optional_thread_guide.stl" you'll require...

I designed an alternative side spool holder adapter to minimize unnecessary plastic waste from existing designs. It's tailored for smooth printing at a 0.5mm line width, utilizing three or more perimeters in each layer. ...Printing this piece hot and...

Design influenced by the Ultimate Spool Holder. ... To get started, you will need: 1x SpoolHolderCentral 2x SpoolHolder 4x 12O3I Washer (designed for M3 bolts) Additionally, you will also require: 4x Bearings (608 is what I used) 4x Short M3...

This is a straightforward butt to slot into the original spool holder.\r\nJust expand the end diameter to 48mm (up from the standard 36mm) and it will prevent spool drops.\r\n\r\nPrint without supports, with at least three walls due to its conical...

I discovered that the original dual spool holder I employed often resulted in issues where the spool would become too loose and fall off, so I modified it by rotating the end part upwards 1 degree to improve stability. Additionally, I added small...

... nuts – this design eliminates those worries altogether. Additionally, it creates space between the spool and the Z-Axis rod, which helps keep build height in check at 150mm, but also reduces the overall unit height, allowing for a sleeker enclosure.

I carefully relocate the spool from its elevated position above the printer to a convenient spot beside it, directly feeding into the extruder. To simplify installation, I designed the new mount to reuse the standard mounting screws and trapezoid...

Loved Adrenaline's design of the side mount spool holder but for my application I couldn't get it to fit in solidly enough in the channels to be stable so I redesigned it to accept some socket head screws and channel nuts. Required: M3 x 3mm...

Like so many others, I found that the friction on that stock tube introduced quite a lot of resistance to the spool's turning until a threshold was reached - then the spool would jump forward a tad. Unacceptable. One of my pix shows the make-shift...

Side placement for fillament for ender 3M4 screws are required

Ender 3 Pro yazıcısını bir kaç gün önce aldım. Her şey muhteşem ama, flament tutucunun çapı küçük olduğu için sanki çekiçle masaya vuruyormuş gibi dönüyor bazen. Farkettimki bu vurmalar esnasında katmanlar arası kayıklık oluşuyor. bunları engellemek...

To keep the spool from tumbling onto my bed, I designed a clever cap.

This adapter is also ideal for those irregularly shaped spools manufactured by UniFast, providing a stable platform for smooth operation. ...Furthermore, it seamlessly supports 200g spools, ensuring flawless performance without any adjustments required.

Filament holder flopping around? Print this and stop that. ...

Inspired by https://www.thingiverse.com/thing:4316465 I made some changes: - instead of threads I changed it to be twist-fix - aimed to copy the original holder in terms of shape and size Supports are required, but not everywhere. I attached a gcode...

I experienced problems with his holder myself, and I didn't want to have to worry about bending the spool holder or not bending it enough and having the spool fall off while printing - With the original design, I encountered issues with it falling...

... interfering with the x carriage. It will fit size wise but since I don´t have any full 4kg spool at the moment I wasn't able to test for stability and if it will hold the actual weight, I will updated it as soon as I had the chance to do so.

Can be used as a direct replacement for the factory spool holder (you should also be able to use the nut which came with the original one). I used a c-clamp to help press fit the bearings onto my axles, which then just drop into the slots of the...

The original file for me wasn't reliable enough because the screws always came loose under the weight of the spool, hopefully this is a more secure fitting. ... requires 2 x M5 nuts

I upgraded my Filament.ca reel with ball bearing hubs using an 8mm x 60mm SHCS as the spindle and drilling a precise hole into the stock Ender-3 filament spool holder to accommodate the bolt securely.

This enables the spool holder to be installed on the left side of the machine, freeing up space inside the printer.

Plug the holder directly into the original unit, then swiftly attach the smaller component - voila, your printing is now live and ready to enjoy.

I recommend infilling 40-100% when you print it out. ...Once printed, simply push it into the existing holder. Don't forget to remove the front nut from the holder first. ...Due to its snug fit, apply a firm push - if it doesn't fit, just try harder!

I made this spacer because I could not find one that fit the spool on my printer arm. This has a larger hole to slide over the spool on the printer. ...I also made it a bit long so there is not a lot of side to side movement of the role of filament.

<p>Print in original size. ...It's simple you just plug this holder into original one then you connect the smaller part and you are done. ...Enjoy your printing!</p> <h3>Print instructions</h3><p>PLA<br/> 50% infill<br/> No support</p>