ender 3 filament spool holder 3d models

Remix from https://www.thingiverse.com/thing:4200759 Spool holder for spools upto 14.4 cm in width, e.g., Prusament 2 kg spools. Simple design, tested to be working fine. ... No supports are needed.

I made a slightly longer version of the filament holder as my spools were running up the stoppers on the roller despite being 60mm wide. I also added an end stop to the holder to prevent any accidents. I also tidied up some of the edges which...

Here is a rewritten version of the text: An adapter designed specifically for fitting onto an Enders holder to ensure smooth and effortless rolling out of OWL filament.

this is a simple spool holder the keeps the spool centered. it replaces the original one. it uses the same nut to secure it on the arm holder. ... 1 gripper ring is needed for keeping spool from sliding of the end, and with bigger spools 2 on each end...

this is a simple spool holder the keeps the spool centered. it replaces the original one. it uses the same nut to secure it on the arm holder. ... 1 gripper ring is needed for keeping spool from sliding of the end, and with bigger spools 2 on each...

A simple tweak is all that's needed to adapt this excellent design for use with the Ender 2, Ender 3, or CR10S standard spool holder. ...Just swap out the front and rear nut holders.

Inspired by a design found on Thingiverse, this 18mm diameter spool holder features an ending locking nut designed to secure smaller spools with an internal diameter of 20mm. ...The same nut used in this holder is also compatible with another spool...

Post print assembly - Important Notes (refer to legend) !!!!!!!!!!!!** Spool Bracket (top right piece that the spool holder will be screwed into): First you will need to manually insert the t-nuts of the spool holder into the bracket one by one,...

it replaces the original one.it uses the same nut to secure it on the arm holder.this eliminates the wobble of the spool that the original spool holder has.included sleeve (make 2, one for each side of the spool).  for spools that get caught on...

I carefully measured out dimensions, replicated the original factory spool holder exactly, and lengthened it to accommodate two fully loaded spools. ...The new design incorporates the factory-issued bracket and a durable plastic retainer for secure...

Securely lock the clamp onto the stock spool holder, ensuring it remains firmly in place and cannot slide off. ...Designed specifically for use with straightforward spacers lacking a mechanism to hold the spool steady.

Fully printable spool holder with bearings for ender3.   Oct. ...2020: Added universal adapter for spools with diameter from 54 - 60 mm and modification for shaft's inner nut (nut -> nut-a).

Simple Spool Extension for Second Spool Holder If You're Out of Space When Printing With a Second Spool. Uses Original Spool Holder. Support Needed Only for Notches on Top. Remove All Supports Carefully Due to Tight Fit. STEP File Included. ... If You...

Once I added a bearing type roller to my Ender 3 v2, all the associated jerking of the spool on the shaft went away, and I noticed that the bracket still allowed the spool to bounce. The bottom of the bracket is just steel bent 90 degrees with no...

The spool holder's flat design allows it to be printed on its side, providing maximum stability during the printing process. This feature is particularly useful when working with larger prints. When printing the spool holder, a moderate infill of...

With this thing you can mount the original Spool-holder on the printer. ...Usefull if you are using a direct extruder

The innovative design of a spool holder draws inspiration from a sleek Acer monitor stand, while incorporating the functional aspects of Ajayamirtharaj's ingenious creation.

A simple plug-in spool holder extension designed to secure wider spools without risk of them falling off, such as those from PM. This extension can be used with or without the central nut, depending on the spool's requirements, and clicks into place...

The tabs slide smoothly into the lower extrusion channel, and if desired, you can also secure them using the factory hardware from the stock spool holder. While being more secure, the spacing remains adjustable for different width spools. As an...

... of bracket to mount the hardbody to. Important Note! This filement spool holder only works for small filament rolls with a maximum width of 55mm (2.165 inches.) The diameter of the filaments center hole should not extend over 17,5mm (0.69 inches.)

To achieve this, I found a 45-degree bracket that allowed me to attach the spool holder at exactly the right position, where the spool would be in front of the extruder. ...I adjusted the screw holes and added some arm supports to accommodate the...

This bracket enables the spool holder to be securely fastened to the side of the printer, positioning it just above the top edge of the frame. ...It attaches to the frame via 40mm M4 bolts and connects to the stock spool holder using 10mm M4 bolts with...

I've been using AngryHulk's spool holder (https://www.thingiverse.com/thing:4834202) for a while now. It's a great system, very modular, configurable and adaptable. But I noticed some of my narrower spools would wander across the extra width of the...

I like designing :-) This will fit the original metal spool holder bracket with the same large Hex bolt. !! Make sure to remove any support in the fillet section, and slow down the process for that fillet section to about 25mm/s2. It uses standard...

I like designing :-) So this will fit the original metal spool holder bracket with the same large Hex bolt. !! make sure to remove any support in the fillet section, and slow the process for that fillet section to about 25mm/s2. It uses standard 608...

I really liked the [spool holder](https://www.thingiverse.com/thing:4888950) I saw on [CHEP](https://www.youtube.com/watch?v=Jp7mRxM1Az8), but mine sags a lot with a new spool on it. Maybe it's my print or material? It worked fine, even with sagging,...

The 3 bearing version caused the standard sized spools to partially slip off one bearing regularly for me. Also flattened one side to allow easy printing horizontally, for additional strength. Requires only a tiny support in the back area. Use the...

The 3 bearing version caused the standard sized spools to partially slip off one bearing regularly for me. Also flattened one side to allow easy printing horizontally, for additional strength. Requires only a tiny support in the back area. Use the...

In testing I don't think it's necessary to have anything on the opposite end as the spools tend to wander towards the far end of the spool holder. This 4th bearing does not inhibit putting the spool on the holder. Uses 4 standard #608 bearings (22mm...

This updated spool mount shifts the spool to the lower side position on the printer, enabling optimal filament routing into the extruder for improved performance. To maximize structural integrity, I designed this model with 4 T slots that provide...