ender 3 filament side mount 3d models

To achieve this, I merged two designs from DrStreet and enlarged the nut holes to accommodate the nuts that came with the Ender 3 spool arm. ...The resulting design doesn't need any extra screws because of the snug fit of the grooves DrStreet included...

Using a minimalist design from coolfooly, I've added slots to utilize the stock lock nuts that come with the Creality Ender 3 spool mount. To ensure a snug fit, I widened them slightly to accommodate the slots. The holes remain the same diameter as...

... It securely clips onto the Ender 3 fan, providing a sturdy support mechanism for itself. To calibrate this setup, you'll need to adjust the X probe settings and Y probe settings within your firmware, specifically in the "configuration.h" tab.

This is a bracket I designed that moves the screen from the right to the left side of the Ender 3v2. I printed with PLA 20% infill. ...Used ShapR3D software on iPad.

This is a bracket I designed that moves the screen from the right to the left side of the Ender 3v2. I printed with PLA 20% infill. ...Used ShapR3D software on iPad.

Remixed to shift more over to side away from bed. ...Prefered this due to lack of mounting screws.

I tried a few side mounts but they always seemed to be in the way. This mount gives a much more even pull to the extruder. No extra filament guide needed! Be careful tightening up the bolts to the 20/20. If your frames Allen head bolts stick up too...

I designed this to make use of the bracket that comes with the Ender 3. ...It will also require a pair of 608 skateboard bearings, a 5/16" bolt that is 4-1/2" inches long, matching nut, and two small sheet metal screws or wood screws. 

... could just flip the spool around! And here is the result. This version is even smaller than the original side mount and is also capable of holding spools as wide as you would like (given you have the right spoolholder.) Still compatible with chains.

Put together a mount for a pitft I had laying around with the help of couple of other amazing makers, thanks to danielvolz and mintonette Additionally to my files you MUST print: this printer mount https://www.thingiverse.com/thing:5402664 this...

WORK IN PROGRESS>>>> I wanted a replacement Spool Holder that mounted from the rails in the frame but could be Swivel so the Filament loads from the back of the Printer. Creality do one but it has to come from China, so I decided to design one...

This file fs for a Wyze Pan mount to watch your 3d prints while they print as an alternative to the Pi cam. ...All you need is a 1/4-20 countersink bolt to mount everything together.

All the spool mounts out there seemed to use T-nuts to secure them to the printer. ...I decided I'd design one which uses the V-slots instead.

I adjusted the LCD position by shifting it to the left and repositioning it more directly upwards, prompting me to craft a basic mounting solution. ...The original screws were retained in their standard configuration.

The human hand holds a robust and highly customizable printer, specifically a REPRAP LCD model that boasts full graphics capabilities, proudly displayed on its left side panel. ...This sleek design seamlessly integrates with the PETSFANG 5015 cooling...

Remixed from DV3D to mirror the original make so that the hardware is facing away and not visible. ...Also the spool reel holder was unscrewed and swapped to the other side of the rail so that the spool can feed correctly into the extruder.

Yet another spool mount for Creality printers, because none quite met my standards. I set out to create one that would work perfectly, and so I designed my own. This design allows you to fold the linkage arm to a maximum of 90°. ...There are two...

The vast array of spool mounts available all relied on T-nuts for stability and attachment to the printer, but I set out to create a more innovative solution, one that would harness the strength of V-slots to provide unparalleled support.

... I feel this gives a really strong support for attaching your spool holder to, especially when it is loaded with filament. Big thanks to qpolarbear for the original design and CHAPP1E for the original remix. Don't want it sticking out so far?

... they were too tight right off the printer. Next, attach the screen and knob. Then attach the LCD ribbon cable, remember it goes into port 3, the far right if you are looking at the underside of the LCD. ...Last, attach the LCD support to the frame.

This is a filament guide for the Ender 3 or Ender 3 Pro that has the filament spool mounted at the side. The diameter of the hole of this filament guide is 4.00mm which is the exact diameter of the stock PTFE tube. The inserted PTFE tube is optional...

Filament Sensor Mount for Ender 3 S1

Toolless / snap-on side filament guide Ender 3 V2. ...No fasteners needed, only 2 standard inline skate 608 bearings.

Side Spool (left or right) filament guide with stock filament sensor for Ender-3 S1 No support needed - Gcode included is for Ender-3 S1 PLA / 0.2 / 15% infill It made for PC4-M10 PTFE connector

Because the others that are similar here generate "screech" noise when the filament passes and also generate dust from the filament that rubs against the extruder entrance and everything is dirty, all this was corrected for the ender 3 v2. This...

Because the others that are similar here generate "screech" noise when the filament passes and also generate dust from the filament that rubs against the extruder entrance and everything is dirty, all this was corrected for the ender 3 v2. This...

Filament Runout Sensor Mount for Ender 3 (Pro)

Creality Ender S1 / S1 Pro Filament runout sensor holder for Left + Right Side

Mount your filament sensor without anoying screws! ... Compatibile with Ender 3 and other printers from Creality.

thirsty_camel made side-entry filament guide for Ender 3 S1, but it had too much of friction when filament was pulled from drybox. I designed these addons to use the original filament guide arm.I used two Wurth 608 2RS bearings. All things is made so...