ender 3 filament roller guide 3d models

I took an Ender 3 v2 filament guide build (remix), and modified it to fit an Ender 3 Pro filament spool holder. The filament guide itself is the same, however, I changed the base to accommodate the filament spool mount for an Ender 3 Pro. v1 =...

This model is made to better guide the filament into a direct drive modded ender 3. ...Especially if the filament is in the middle of drying or a dry box.

This is a simple filament guide endcap that I designed for my Ender 3 v2 in a Lack enclosure, to stop the filament from rubbing the edge of the frame.

A simple minimalist filament guide for Ender 3 Pro users equipped with Direct Drive and using filament boxes such as the eSun eBox. ...Prints in 30 minutes using a 0.8mm nozzle.

This model is made to better guide the filament into a direct drive modded ender 3. ...Especially if the filament is in the middle of drying or a dry box.

While going through the journey of getting the most mods and upgrades possible for my ender 3 pro, I've discovered a neat little filament guide. The thing that sold me was that the guide actually had a roller in order to release the stress from the...

Summary These things are two filament guides for the Creality Ender 3 V2. They fit the end of a 20mm European extrusion on the left side of the Ender 3 V2 top rail. The filament guides use a standard pressure fitting and a 60mm length of 4.00mm OD...

Inspired by Ender 3 Filament Guide **UPDATED** by robathome I wanted a guide which did not require threading the filament. 1. I maintained most of the features from the original except I extended the clevis into a loop to allow an opening for the...

... dimension was increased accordingly. Creality CR10/Ender 3 Filament Guide Dimensions: For those relocating their filament spool above or below their printer, these measurements are provided in inches. ...Scaling for metric units will be necessary.

Filament guide for 3D-printer Creality Ender 3 or Ender 3 Pro on the top beam. This is required when printing from a filament dryer. ...You need 2 pieces of M3x40 screws and 2 pieces of M3 nuts (a rubber lock nut is recommended).

I remixed this Ender 3 filament guide simply because it's easier to print and there's really not a need to have the hassle of making the 2 pieces fit together...

Here is a rewritten version of the original text: A Beginner's Easy-to-Follow Guide to Printing with Your Ender 3 Filament. ...Estimated printing time: approximately seven minutes.

This is a minimalist filament guide for the Ender 3. This requires an M5 screw and T-nut. ...Mount it on the upper left corner of your printer with the mounting screw on top.

The Ender 3 Pro Filament Guide has been secured firmly to the Z-Stepper. ...To ensure a stable connection, an M3x30 screw must be tightened into place within the stepper motor itself.

So i got sick of my guide that i printed off here falling off when using my sunlu filament dryer so i made my own that bolts to the gantry of my Ender 3 V2. No extra parts needed, bolts onto gantry roller nut. I find its still easy to load filament...

This is a remix of mousikantis's "Ender 3 Filament guide" https://www.thingiverse.com/thing:3607660 I found that when I mounted my spool lower using the Rocket ( https://www.thingiverse.com/thing:4691695 ) that the guide would bind and chatter as the...

Needed a shorter filament guide to more easily put the Ender-3 in a box for ABS printing. Get the fitting end clip from the original thing. This short version fits in both ways better. However, this means it needs a bit of support. ... OpenSCAD remix...

The filament guide to move the filament into a better position on Ender 3 Pro (and possibly other Enders). 2 files: run the test first, see if it fits correctly. If not, go up or down in scale, test again. When ready, run the guide file with the same...

... of your z screw rod to not rotate.Open slot for easier filament replacement. Good filament angle even at highest position!Print instructionsInfill 15%, Support: Raft! I am testing another approach now - try it too: Extruder Filament Guide (Ender 3)

Couldn't find a simplistic design of a filament guide for my Ender 3 Max, so i made my own. Needs only a 608 bearing. Clips on, no screws. Takes a bit of a push, clips into the hole in the mounting plate. ...EDIT: Added a new improved guide arm to help...

Filament guide using a pulley (with bearing) to minimize friction for Ender 3 V2 that clamps to the frame using M3 screws. ...The filament guide does not depend on any other accessories and works with dual gear or single gear extruders that have...

This is an adaptable filament guide designed specifically for the Creality Ender 3 Pro, although it may also be compatible with other versions. ...Once you remove the top cross strut, the guide should snugly fit down the left strut, providing precise...

I'm remixing the Ender 3 Filament Guide by Filboyt, giving it a fresh spin. To make room for other projects, I've moved the Ender 3 printer to the edge of my work surface, where it's nestled snugly against a wall. ...This strategic placement frees up...

Filament guide for Ender 3 v2 which keeps the filament from coming into contact with the z-axis screw. Works even better with a top frame filament guide that gives a much better filament radius. Attaches to the z-axis nut fitting using existing...

Filament Guide Attachment for Ender 3 Top Bracket The Ender 3 requires a secure way to manage its filament, ensuring it remains at a safe distance from the z-axis screw. A simple solution is needed to prevent entanglement and maintain print quality.

I made some adjustments to Matt Ellison's Ender 3 filament guide, adding a space to the ring for smoother loading and unloading of filament. I left all else intact from the original design. The gap was specifically tailored to fit 1.75mm filament...

Instructions: Remove your filament Remove the bolt and washer that is in front of the filament path Slip the guide onto the extruder assembly as shown in the picture Re-tighten the bolt down onto the filament guide without the washer Feed your...

Check out my latest creation of a printable Ender 3 Pro Filament guide specifically designed for 1.75mm filament diameter: Take a look at my brand new generation of this filament guide here: https://www.thingiverse.com/thing:4274387 If you like what...

Simple filament guide for Ender 3 & Ender 3 Pro - Slots perfectly into the side of the 2020 extrusion profile. UPDATE: 04/01/2020 Added new version (V2) with several key modifications: - A specially designed slot allows for easier insertion and...

3D printer filament guide specifically for the Ender 3 S1. For a dehydrator at the same level as your 3D printer. It guides the filament from and to the filament senor to the extruder. I used ABS for a stronger print. Sanded the hole a little to make...