ender 3 fan duct 3d models

Upgrading the cooling fan duct involves a clever twist on the standard approach by aiming for the nozzle instead of its traditional placement. ...To execute this modification effectively, it's crucial to introduce structural support solely through the...

... to enclose the upper fan, providing extra support in case the fit is not perfectly snug. Finally, an adapter has been incorporated to accommodate 40x40x20 part cooling fans, allowing for flexibility with fan ducts or direct replacement if desired.

To address this issue, I merged Filboyt's fan duct ring with nghtshd's duct to create an additional nozzle that slides effortlessly into the Fan Mount. Unfortunately, Filboyt's original duct didn't mesh well with my stock fan, so I opted for a 5015...

The Karo cooling fan duct was designed with several key considerations: - I want to be able to print a 3x3 lattice cube without the edges bending up and ruining the print - I really don't want to remount BL Touch because recalibrating it is just...

I made some investigations and experiments and found that the stock fan duct has a little bit deviated blowing direction. And I made an improved design that can significantly decrease the stringing. ...Please print with ABS or PETG to avoid thermal...

I made some investigations and experiments and found that the stock fan duct has a little bit deviated blowing direction. And I made an improved design that can significantly decrease the stringing. ...Please print with ABS or PETG to avoid thermal...

I made some investigations and experiments and found that the stock fan duct has a little bit deviated blowing direction. And I made an improved design that can significantly decrease the stringing. Please print with ABS or PETG to avoid thermal...

also filled some grooves inside the duct cause they were causing thin wall conditions Used the MS 3d builder so it doesnt look clean but it does the job I printed it at 45deg, with no inside supports to minimize bridging, looks like it would also...

Works with: 1 40x40x10 axial fan 2 40x40x10 radial fan Screws i use. Socket head 1 M3x10 + nut and washer Button Head 7 M4x14 4 M4x16 2-4 M2x8 or longer works as well with bl touch Printed with standart Cura 0.2 settings and tree...

I wanted a fan duct for the stock Ender 3 radiator with a volcano hotend but couldn't find that combination so I have modified the "Satsana Ender 3 Fan Duct" and extended the ducts down by 10mm and also made a bit more room inside for the volcano...

This is a remix of the "CR-10/Ender 3 Hotend Fan Duct" from pixarfanatic95. This differs from the original by: - a BLTouch mount on the left side of the duct - BLTouch Offset by: x= -32 and y= -9. - Elongated holes, so you can adjust the height of...

A simple Ender 3 / Pro fan duct to attach a Noctua 40x40x20mm (Noctua NF-A4x20 FLX) fan instead of the original one. The original part-cooling fan can be attached on the right side. You can use all the original screws. Be careful: The Noctua Fan...

A more direct nozzle cooling with an extension which blocks hot air from the hotend. ... Gamla 3D Workshop

taken from https://www.crealitycloud.com/model-detail/31474

I added a second cooler.

Easy two print parts, and glue it together with the best model glue available, UHU Hart especially suitable for gluing ABS.

Modified the mount to accommodate for CR touch. Will also work for BL Touch. ...Don't use supports as they will generate inside the model.

This 3D print is specifically designed to work seamlessly with a BLTouch probe, allowing for precise and accurate measurements of the printing bed's surface. ...To take full advantage of this feature, it is crucial that the user enable custom support...

Satsana avec ajout du support touch-mi de chez hotends.fr Un modèle pour les ventilateurs d'origines. Un modèle pour deux ventilateurs de 40x40x10. Position TouchMi : X = -52 mm Y = -6 mm Position BlTouch : X = -49 mm Y = -10.5 mm ...

To seal the bottom part, reduce unwanted air that can cause warping in the ABS by allowing it to escape. ... Note: You must release the hotend and bowden to assemble.

This is a remix of the Satsana Ender 3 Fan Duct that makes it where you can use the free completely printed direct drive I designed and the BL-touch. THIS ONLY WORKS IF YOU HAVE A TOO LONG HOTEND like this one from Amazon:...

The following is the changes I made to the Fan Duct Corrected the width of the 5015 Fan port as it had a gap that would allow air to escape Added support for the CRTouch as the cable outlet is in a different location. I had to remove the center hole...

... as 40mm fan (measured from bolt holes center to center. I am using Creality Ender 3 V2. Changes: 1. Added the BLTouch attachment. 2. Increase the fan size for the heatsink to 40mm. 3. Incorporate vanes for more efficient airflow. ...

Hi all,I modified the Satsana Fan duct to mount two noctua 40x40 silent fans.Its based on the V59 version of the fan duct.To mount the part cooler you need some additional M3 screws.I also added some covers for the fans.

... wire position. I have created both a 4010 and 5015 version. Compatible with the stock CR Touch mounting bracket. I own the Ender 3 Pro, and have only used this duct on that printer. I have no idea if it would fit anything else. ...Give it a try!

Added BLtouch to the remix now you will have the Fan Duct with 2 Cooling Fans and Bl-touch You will need the original BLtouch Bracket

When I upgraded my Ender-3 to direct drive I decided to buy an aluminum stepper mount, but it was too big to work with this Satsana Fan Duct. Using a little bit of magic I was able to make this work and here it is for anyone else who wants a fan duct...

Thank you, Ahmet, for the remixed you can find his remix here: https://www.thingiverse.com/thing:4846449 I made this remix because I use the CR10s PRO hotend and the Satsana Fan Duct for Ender 3 with a 4010 blower fan and BLtouch. I updated the...

This is a bunch of remixes so that the Ender 3 can have everything I wanted at the same time: 1. A good fan duct that can hold 2x 5015 fans. I've tried others and they where too flimsy 2. A direct drive extruder using stock parts only 3. A drag...

Super Fan Duct Easy to Print No Vibrations Perfect Cooling for Layers and Cold End. You Can Use a 4020 Fan. A Nice Pick is the 4020 Form Cooltek. ...Visit Amazon.de for More Information:...