ender 3 fan duct 3d models

... quiet fan. ... Designed for the Ender 3 or with similar Fan Housing Mount. Print the Fan Holding Adapter with PETG an minimum 50% Infill. Share your Experience. ... The Overhang Test is from zumili: http://www.thingiverse.com/thing:1564848

A simple fan duct i have designed for the ender 3 with hero mi base (stock blower) that has given me better results than the hero mi designs or stock blower.

Satsana Fan Duct with fan guard

This is an upgraded version of Submano's Cooling Fan Duct for the Ender 3. After discovering that it wouldn't fit my printer, I remixed this design to make adjustments. It now extends by 1.8mm in the middle. The original design got too close to the...

3:45 h printing time (50mm / s) Powerful - 5015 fan with smooth and large air duct directly to the nozzle Lightweight - only about 30g material but stable BLtouch compatible - offsets X -27.5mm Y 0mm Klipper approved - stable even at high speed and...

I created a fan Duct for Ender 3 hotend that can also be added some led light from an old led strip. Optimized airflow and compatible with silicone cup in the nozzle (easier to change the nozzle) Use it, test it.. enjoy it :) Pint no supports.. I...

PayPal account: beagleinside@gmail.com Paypal.me link: https://paypal.me/adarkstudio Thank you page: https://pastebin.com/raw/gTt8iE5a Best regards, Nio In an effort to quiet my Ender 3 Pro, I designed this hotend fan duct using only 4010 or 4020...

Here is a remixed version of this great fan duct for the Ender 3. I have had very good success with this duct and did not want to ditch it when I added the direct drive mod (https://www.thingiverse.com/thing:3386628). I also wanted to add a bed...

PayPal account: beagleinside@gmail.com Paypal.me link: https://paypal.me/adarkstudio Thank you page: https://pastebin.com/raw/gTt8iE5a Regards Antonio In the attempt to quiet my Ender 3 Pro, I designed this hotend fan duct to use 4010 or 4020 silent...

A little remix of te already great Satsana fan duct for the Ender 3 printer with BL Touch mount which keeps the off set to a minimum. 2 Versions are included, one for Boden tube and one for direct drive printers. Off sets for Marlin are -28mm for X...

In the meantime, here's my two-fan design, which outperforms the AIRO family: Ptairoductylus https://cults3d.com/en/3d-model/tool/ptairoductylus-a-performance-based-ender-3-cr10-maybe-5-dual-fan-duct Update 3: Added BLTouch Mount STL Print it at 0.24...

Satsana Fan duct remixed for usage with DC42 IR probe. To install probe unsolder dupont pins and solder a low profile connector to the back of the board or 3 wires coming directly out of the back of the board. Install with capacitor facing forward.

Satsana Fan duct remixed for usage with DC42 IR probe. To install probe unsolder dupont pins and solder a low profile connector to the back of the board or 3 wires coming directly out of the back of the board. Install with capacitor facing forward.

... up to 240 C. Because sock leaves uncovered the upper portion of hotend. This duct install over stock fan and properly directs air flow to the coldend. You get stable temperature, and better cooling for the cold end portion. ...It prevents heat creep

I’m 14 years old and I made my own fan duct because I just found all the other’s to big and heavy or just ugly on the printer so i made the KAHIKU and wanted to share it with poeple so it could be use by you and improve for specific fan or...

Definitely better than the stock fan duct. I would like to make the air blow a bit more under the nozzle since right now I think it's a bit far, but still, works nice. Results I did find noticeable improvements in overhangs, doing a 70º overhang...

Definitely better than the stock fan duct. I'd like to make the air blow a bit more under the nozzle since right now I think it's a bit far, but still works nice. # Results I found noticeable improvements in overhangs - doing a 70º overhang test...

The human model features a 60-millimeter fan that can be securely attached using M3 screws and nuts.

... for the mounting screw was too small in the original, I punched a 8mm hole through which should be wide enough for most bits drivers to fit through. ... I also added a slot for the wiring of the cooling fan that protruded out the back in the original

The hole for the mounting screw was too small in the original, I punched a 8mm hole through which should be wide enough for most bits drivers to fit through.I also added a slot for the wiring of the cooling fan that protruded out the back in the...

Bl-touch support for ADKS - ENDER 3 FAN DUCT V3 https://cults3d.com/en/3d-model/tool/ender-3-adks-fan-duct-no-supports-needed offset : x:-43.2 y:-6.0

This is a Remix of Satsana Ender 3 Fan Duct https://www.thingiverse.com/thing:4369859 Offset: X: -47 Y: -8 Direct drive mount - https://www.thingiverse.com/thing:3386628 Bl touch spacer - https://www.thingiverse.com/thing:3072487

This is a Remix of Satsana Ender 3 Fan Duct https://www.thingiverse.com/thing:4369859 Offset: X: -47 Y: -8 Direct drive mount - https://www.thingiverse.com/thing:3386628 Bl touch spacer - https://www.thingiverse.com/thing:3072487

This is a Customized Satsana Ender 3 Fan Duct Remix \r\nhttps://www.thingiverse.com/thing:4369859 \r\nOffset: X: -47 Y: -8\r\n\r\nI added a BlTouch mount and now it fits with the Drive (https://www.thingiverse.com/thing:3386628) perfectly. You will...

Ender 3 PSU Fan Duct/Silencer. This fan duct/silencer features smooth surfaces that require precise gluing techniques since they lack any studs, making it crucial to achieve a nearly invisible bond between the parts. ...A solid version of this model is...

This is a remix of the Satsana Ender 3 Fan Duct for CR-Touch by E30Andrew remix for Ender 3 Pro. I purchased the Creality Official Ender 3 Direct Drive Upgrade Kit, Comes with 42-40 Stepper Motor Hotend Kit, 1.75mm Direct Drive Extruder Fan and...

A heavily modified version of Eric Anasta's Satsana Ender 3 Fan Duct by Ammar Yasir has been created. This updated design includes a BLTOUCH mounting space, as well as room for a 5015 blower fan. A pressure clip on the right side is intended to...

it is possible to skip the extension cable but you will lose some z-height I also have a version for the stock extruder available but it is currently untested see cura screenshot for print orientation thingiverse won't let me add multiple source...

This is a modification of the Satsana Ender 3 Fan Duct to fit an Ender 3D Pro direct drive with CR Touch. It has been further modified to split. There is a base that mounts to the printer and one bolt holds the Santsana to the base mount. This...

I've come across an awesome upgrade kit for the Ender 3, but as you can see from the image, it required some tweaking to perfectly match my Ender 5's specifications. ...If you own an Ender 5, consider yourself lucky!