ender 3 extender 400xl 3d models

Here is a example of the Ender Extender 400XL for the Ender 3 Pro. I do not own any rights to any products used for this model and do not want any credit for them. I've quickly put this model together using publicly available resources to make a...

I that design and offset the frame mount bracket a bit more so that the USB ports would not have interference with the 1010 extruded cross brace that is part of the Ender Extender 400XL kit. I also removed the tab from the rear that was for mounting...

This is for the X-gantry of the Ender Extender 400/400XL Kit I just used a drill to tap the holes a little bigger and used t slot nuts I used 24v white led strips but you can use whatever obviously, I actually always super glue (the gel kind) the led...

This is for the X-gantry of the Ender Extender 400/400XL Kit I just used a drill to tap the holes a little bigger and used t slot nuts I used 24v white led strips but you can use whatever obviously, I actually always super glue (the gel kind) the led...

Cable chain brackets designed for the Ender Extender 400XL. (May work on other versions) This setup will require you to extend your wiring. The PM_v1.3_EZR_Struder_Front_Facing_Adapter_w_Cable_Chain_Mount is designed for the Printermods.com direct...

Z-Brace for the ender extender 400XL, requires following hardware:M8 threadM5 bolts M5 T-NutsOptional: washers Additional tip: my Z extrusions were not entirely flat on the bottom side. I used a thin metal plate to compensate for this which...

this is a remix of a case design for the skr 2 by SB903 BigTreeTech SKR 2 case for Ender 3 Pro: https://www.thingiverse.com/thing:5013886 I have adapted this to fit an ender 3 that has been upgraded with an ender extender mod

This is a case for the back of your ender extender 400xl to house a raspberry pi, buck converter, motherboard and a fan i can make another version for the stock ender 3 v2 if you comment below and ask for it KEEP IN MIND THE SD CARD SLOT IS COVERED...

This is a case for the back of your ender extender 400xl to house a raspberry pi, buck converter, motherboard and a fan i can make another version for the stock ender 3 v2 if you comment below and ask for it KEEP IN MIND THE SD CARD SLOT IS COVERED...

Designed this two-part wire strain relief for the Ender Extender 400XL and the 600-watt AC-powered silicone heater. This mounts directly on the bed just offset from the center enough to route the wires away from the motor and all. Use M3...

Ender 3 Pro 400XL Extender Light Bars - designed in Blender (files included for customization) -Designed for 20mm light strips -Use M4 hardware X Gantry Light Bracket - 310mm x 20mm Top Front Crossbar Light Bracket. ...- 440mm x 20mm

This is a quick and dirty remix of the excellent Rigid Systems Z brace for the Ender Extender 400xl. The bottom brace brackets were modified to fit the non-pro version of the Ender Extender 400xl. ...Use the original version of the top brackets!

23mm spool extender to get extra space for the spool, so you can use in combination with any other designs.

I didnt have long enough screws for the display mount extender necessary for to the nozzle cleaning brush. This redesign allows for usage of four shorter M5 (e.g. M5x20) screws and two M5 screw nuts. ... Print Settings Rafts: No Supports: Yes ...

Simple upgrade adds double capacity to standard Ender 3 spool holder by replacing original nut with extender that matches standard spool width, allowing two spools to be held securely in place.

Just a Simple Print to Extend the spool holder on your ender 3, attach via glue or a square of tape to make it a snug fit. ... Comfortably fits any spool smaller than 145mm

Double rail V Slot extender for the Ender 3 series (Pro and V2). Attaches to the front left using the 2 bolts that came with the printer which connect the mainboard cover to the V Slot (no extra screws required - use the included hex wrench). ... I used...

450mm bed extender for the Creality Ender 3 Belt printer. I have included 2 different roller designs, one is a full cylinder with a bearing pin on one end printed separately, the other is split in half for printing on the belt printer itself. In...

This is a Bed Extender for the Ender 3 Belt Printer. Rollers are the same diameter as OEM and close together. Liner is printed in all walls and TPU for a soft exterior. Inner roller doesn't need much infill as it just goes along with no weight...

Extension for the original spool holder on the Ender 3 S1 - allows for larger 3.7kg+ reels to be used. ...Compatible with Creality's standard spool arm and shaft that comes with the 3 S1.

In a nutshell, after a few months with my first 3D printer (ender 3), i started to feel "limited" by it's printing volume. I bought aluminium extrusion and made it bigger in Z and Y and i'll do X next. The only problem now is the very small bed. ...

This design was printed with these settings for myself with Prusa Slic3r. ... Infill : 30% Resolution : 0.2mm Supports : Bridging Material : ABS Wall : 3 2021-12-01 - Printing in progress.

Wanted a foot for the back area and was only given one foot for the Y when I bought the ender extender kit

Extending by about an inch solves this problem, This should work on all Ender 3's (Std, Pro, V2) and possible other models like the CR10 etc (As long as it is using the metal spool holder from creality (I know they are identical parts on Ender 3 Pro...

My dad got me this Ender 3 Pro for Christmas along with some filament however he got me a 4 pack of filament that are each 250 grams on small spools that did not fit on the included spool holder. ... Therefore I made this extender that fits inside of...

Extend Your Stock Ender 3 Filament Spool Holder. To accomplish this task, you will require an adhesive. ...Begin by printing the Body1 component, followed by selecting either the Body2 model depicted in the provided photograph or the Body3 variant,...

I printed this side spool holder for my Ender 3 Pro: https://www.thingiverse.com/thing:2967567. However, the Y-axis motor was in the way for the spool so I came up with a simple extender as an easy fix. ...It's designed to use two M6x30 screws instead...

After upgrading my Ender-3 with a rear electronics case, accessing the Micro SD card became increasingly frustrating due to its inconvenient location. Furthermore, I didn't want to utilize a bulky SD card, so I opted to purchase a simple Micro-SD...