ender 3 enclosure thingiverse 3d models

It is a rough remix, but it got the job done.

<p>I really liked the original, but I wanted a front case, due to not having space in the rear, and wanting to maintain access to the SD card slot.</p> <p>This is set up for an SKR 1.4/1.4 Turbo board and a 30mm fan on the left, and a Pi, buck...

I mounted my Raspberry Pi in the rear and chose to install the touch screen up front using Tronnic's Case & Holder. This is the precise touch screen I selected:...

this is my own version of an enclosure for the ender 5 and ender 5 pro. You will need to be able to drill, cut and tap aluminum extrusions', v rails are recommended, measurement on step file are correct size for the ender 5 and ender 5 pro, this is...

This print was created to allow users to mount their Ender 3/Ender 3 Pro LCD externally using some of the extra fasteners and cables from our Universal 3D Printer Enclosure Kit. IMPORTANT: You must print both Arm A and Arm B (they are not the...

This print was created to allow users to mount their Ender 3/Ender 3 Pro LCD externally using some of the extra fasteners and cables from our Universal 3D Printer Enclosure Kit. IMPORTANT: You must print both Arm A and Arm B (they are not the same...

This is an enclosure I designed to house the MKS TFT28 display and mount to the left 4040 extrusion of my Ender 3 Pro. It's a snug fit when assembled together. The Clamshell closes up with four M3x8mm screws, but you may need ten-millimeter length...

Please use v042 for Raspberry Pi 2/3** This is an enclosure that I designed to go under the LCD display of the Creality Ender 3 Pro (probably will fit perfectly to Ender 3 too) that also holds a Raspberry Pi 2/3 and now 4. ~~Later on, upon request,...

This print was created to allow users to mount their Ender 3/Ender 3 Pro LCD externally using some of the extra fasteners and cables from our Universal 3D Printer Enclosure Kit.&nbsp;IMPORTANT: You must print both Arm A and Arm B (they are not the...

This print was created to allow users to mount their Ender 3/Ender 3 Pro LCD externally using some of the extra fasteners and cables from our Universal 3D Printer Enclosure Kit. IMPORTANT: You must print both Arm A and Arm B (they are not the same...

This includes a cut out for the 4040 Damper legs in the front Right corner for the Ender 3 Printer.

Remixed from ‘Creality Ender 3 Pro - Raspberry Pi 2/3/4 + LCD Enclosure’ by eoyilmaz, specifically v042 for Pi 2/3. Note: **This remix only works for Pi 2/3**, not 4. The original is a really beautiful design. To suit my Pi 3B setup this remix...

This is a closure for Raspberry Pi 3 and Ender 3 Screen. I fixed heat issues running my Pi and the Ender display by adding a 30mm fan to the box. Pi used -...

Customized version of https://www.thingiverse.com/thing:1696246 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1696246

I'm working on Ender 5S 1 Enclosure Project. ...Enclosure will be ready soon :)

I crafted a maker's badge to commemorate Thingiverse's revamped website, which unfortunately crippled its once-essential search feature.

This case will probably block the SD card reader and micro USB port on the Ender 3 Pro, and V2, which have the SD card reader and USB port at the top towards the left of the electronics compartment. However, it would be very easy to just move the...

A case designed for the original Ender 3 a Raspberry Pi 4B and a 3.5" TFT screen that connects via the GPIO pins. It also comes with a holder for the stylus that comes with most of these screens. ...The holder snaps onto the stylus and holds it...

A case designed for the original Ender 3 a Raspberry Pi 4B and a 3.5" TFT screen that connects via the GPIO pins. It also comes with a holder for the stylus that comes with most of these screens. The holder snaps onto the stylus and holds it...

Here's My Design for the Ender 3 Pro: A Comprehensive Upgrade Guide If you're planning to upgrade your controller board on the Ender 3 Pro, this design is specifically tailored for the SKR 1.3 or MKS Gen L boards. While it should also work seamlessly...

Quick remix to support a 3.5 TFT screen connected to GPIO for GalvanicGlaze's Ender 3 v2 electronics case. Plan to use jumpers to connect to my Raspberry Pi. Also used gunnarfreyr's 3.5 TFT case to make the opening and the back for the faceplate. ...

Quick remix to support a 3.5 TFT screen connected to GPIO for GalvanicGlaze's Ender 3 v2 electronics case. Plan to use jumpers to connect to my Raspberry Pi. Also used gunnarfreyr's 3.5 TFT case to make the opening and the back for the faceplate. !!!...

This is a remix of the RPI 4 v54 enclosure by eoyilmaz from his excellent file. It is made to include an SSD drive with Inland SSD USB 3 adapter along the back. Not perfect as there is an opening in the from of about a 1/4 square as the framework...

Remix of 2 Thingiverse Designs 1: Kilroy01's Ender-5 Control Panel Back Cover https://www.thingiverse.com/thing:3353394 2: Wolfganghsu's Snap-on LCD Cover for Creality Ender-3/Ender-3s/Ender-3 Pro/Ender-5 https://www.thingiverse.com/thing:3670360...

Ender logo for your enclosure. Used the STLs from this print on Thingiverse (https://www.thingiverse.com/thing:3078936), and added a background. Printed with a filament change for blue on white finish. Print instructionsPrinted with PLA on MK3S+,...

on ender 3 max the enclousure rests alot on the frame and likely only needs the screws, but on ender 5 only a small portion rests and it felt wobbly so i adapted it. changes:oversized the HDMI, charger and audio socket holes as they were to tight to...

A simple way to keep the enclosure lid on my Ender 6. No new hardware is required. ...The stock enclosure screws are enough to hold the clips in place.

Enclosure for a Ender 5 Plus, work in progress, will update as I get more completed.Material is 2mm Aluminum, if needed I can upload the DXF flats.

Acrylic Measurements: Top - 20 1/2" X 19 3/4" Front door - 6 7/8" X 17 3/4" Rear - 7 1/8" X 18 1/4" Sides - 3 1/2" X 20 1/2" Printed parts: 40x40 bracket - 10 required 40X40 Front Tabbed bracket - 2 Required --> These work with my Y axis belt...

Ender 3 Pro enclosure for a Raspberry Pi 4 and a BIGTREETECH TFT35 E3 V3.0