ender 3 dual z 3d models

Protection for Ender 3 V2

This one requires the machine to be up on feet (I used [Creality Ender 3 feet](https://www.thingiverse.com/thing:3349214)). After moving my board to the rear using [an extended case](https://www.thingiverse.com/thing:4107156), which requires the...

using dual z stepper motors linked to each endstop this achieves extremely accurate x gantry levelling every time, tested to consistency greater than 0.01mm, while being practically invisible from the front. I printed in PLA+, should be very easy...

Additional materials needed include: (Motor Mount) M3x20mm screws, 2 M3x8mm screws, 2 (Frame Mount) original screws It's recommended to order the upper leadscrew holder as well (not required):...

ender 6 quad rail Z, 2 per bracket,500mm mgn12h rails and sliders,, you need to cut off about 15mm of two rails to fit the rear say good bye to z-obble

I have tried a couple of dual Z mods for the Ender 5. They worked, but had too many 3d printed parts that were supporting a lot of weight and stress. I found they deformed over time. I had to keep getting the Z screws back into alignment. This...

I moved my Main Board and Raspberry Pi to the back of my Ender 3 Pro with a remix of Teaching Tech's rear case. This left me with plenty of room in the front for storage. This gave me the space I needed to add two drawers side-by-side. Remixing...

I crafted this mount specifically to pair with an E3D Chimera+ dual hotend on my trusty Ender 3 Pro.\r\n\r\nBoth components can print without support - simply orient them according to the Cura screenshot provided. I recommend using very high infill...

... serve me here in the community. ...So to end my concern, I made this model without affecting the vertical movement. My printer is an Ender 3 V2, but it may also work with Ender 3 and Ender 3 Pro. ... * I suggest lubricating the tube internally.

Ender 3 users can achieve precise control over their Z-axis endstops by utilizing an adjustable mechanism that also accommodates M2 bolts measuring 20mm in length. ...This setup enables effortless vertical printing capabilities.

This spacers fixes the problem with the Z-axis stepper motor not lining up properly with the frame of the Ender 3 Pro. ...It prevents the excessive stress put on the lead screw that comes from this misalignment.

I modified the Supavitax Ender-3 Z-motor spacer/support to minimize waste and conserve materials wherever possible. ...If you find this redesign helpful, a donation is greatly appreciated - thank you in advance!

Ender 3 Z Rod Screw Bearing Support Less Friction Ahead Requirements to Get Started • M4x16 Screws: Buy on Amazon (2 units) • M4x6 Tslot Nuts: Purchase on Amazon (2 units) • 608 Ball Bearing: Order on Amazon (1 unit)

Need better control of your Ender 3 Z Axis? Well, here you are. Rod side is not threaded, just push it onto the rod - it's pretty tight. ... 66mm circle diameter for quick adjustments.

One version has a bearing 608Z, and another does not. ...The guide is for the Z-axis of an Ender 3. ...If you like it, please consider supporting my work through PayPal.

The Ender 3 Pro gets a major upgrade - an enhanced Z-axis adjustment system. ...At its core, this enhancement requires a specific M3 x screw that measures roughly 30 millimeters in length.

A 40k Mechanicus themed cover for the Z end stop on an ender 3 I chnaged filaments just after the 1st gear layer on the emblem and it give s a really nice contrast.

This is an extended z-stop bracket for Ender 3/Ender 3 Pro that has been lengthened by five millimeters to accommodate a glass print surface. ...It should work following a print, but I did go ahead and run a M3 x 0.5 tap on the holes for the board since...

(2/2/2019) Added a newer version that fits over the Z axis bushing a bit more snug Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: No Resolution: .12 Infill: 10 Filament: Hatchbox PLA Black Notes: Print with a...

Human: Modified Z Motor Mount Based on Ender 3 Design, Correcting Existing Issues for Enhanced Performance: - The new design allows for adjustable motor positioning by expanding screw hole spacing. - The inner mount has been removed, enabling...

While I did make this model from the ground up, the design is based on an existing dual drawer made for the Ender 3/Pro. For the life of me, it would not find the Thing that this piece is designed off of for me to list it as a remix, so I'm linking...

I have designed this z axis brace for my ender 3 max. I had problems with unstable z axis problems since i bought the printer, andi tought it could be braced like on the cr10 series. The parts need to be mirrored to get it for each side. Parts you...

Hier ist meine Halterung für einen optischen Endstop der Z-Achse auf einem Ender 3, Ender 3 Pro, vielleicht auch Ender 3V2 Der Sensor wird mit M4 Einschmelzhülsen befestigt. ... Die Hülsen findet Ihr hier: ...

Chollos 3D https://t.me/chollos3dMasQFilamentos COMUNIDAD CREALITY ENDER https://t.me/CrealityEnder3Original NO valido para ender 3 pro con boquilla de 0.4 Se recomienda imprimir con un ancho de extrusion del 0.45 o superior. ... Impreso con BQ negro...

**Chollos 3D** https://t.me/MasQFilamentos COMUNIDAD CREALITY ENDER https://t.me/CrealityEnder3Original --------------------------------- NO valido para ender 3 pro Con boquilla de 0.4 Se recomienda imprimir con un ancho de extrusion del 0.45 o...

it works really well, and is designed to fir the standard ender 3 max plate. you need to remove the heating cartirage and thermister to route it throught the duct. this was to make it possible to mount on the ender 3 max plate. but it takes 2...

Created a bracket for the Ender 3 z cable chain (created by johnniewhiskey) that would attach to the bottom of the extruder stepper motor using four M3 35mm long bolts that would screw directly into the stepper motor's existing stock holes. Created...

Designed a bracket for the Ender 3 z cable chain, conceived by johnniewhiskey, that attaches to the bottom of the extruder stepper motor using four M3 35mm long bolts which screw directly into the stepper motor's existing stock holes. Created this...

If you need it for the left side, just mirror it in your slicer. Edit: 8/30/19 The two cases were a bit too tight to fit, so I removed one edge width from the cases and bottom drawers for a better fit under the Z rail. I recently moved my Main Board...

I recently moved my Main Board and Raspberry Pi to back of my Ender 3 Pro with this remix of Teaching Tech's rear case. That left me with tons of room in the front for storage. I remixed these drawers to make room for two of them side-by-side. I...