ender 3 dual extruder 3d models

I designed this to snap on the extruder arm and help guide the PTFE tube with filament into extruder to avoid bending the filament (see picture without the guide) Support needed for printing the PTFE tube guide.

Remix from https://www.thingiverse.com/thing:3833174 I Added some extra support to prevent bending, and also a chain adapter for https://www.thingiverse.com/thing:2920060 Haven't tested yet.

Ender 3 / 5 Direct Drive Extruder DotBit Dual Drive Extruder Setup

This Ender 3 Aluminum Alloy Direct Drive Plate Upgrade Kit For Creality CR10 Ender-3 Ender3 Direct Extruder Adapter Plate offers an efficient and cost-effective solution. To prepare this design for printing, I used small tree support in Cura, which...

I swapped out my existing bracket for one that's a little unconventional, allowing me to bypass the original lip and giving me more control over the extruder by adding a miniature lever that makes it a snap to press down on.

Use pulley halves and bearing retainer from https://www.thingiverse.com/thing:4654143. Supports are required for the arm.Marlin config changes can be found here :...

Original is great but sensor mounts too low for dual gear extruders. Mixed the arm onto TheKojent's mount. ... Use pulley halves and bearing retainer from original.

I design this to uplift the cutout sensor to fit the height of the Bigtreetech Dual Gear extruder MK8. This allow to level the filament exit of the sensor to the entry of the extruder. ...You'll need 4 x M3x20mm to bolt it to the frame.

Had wheels, axles and bearings left over from work on this [adjustable filament spool holder](https://www.thingiverse.com/thing:3648130/) and wanted not only to reuse them, but to have a matched upper and lower guide with lower guide at suitable...

I designed this part specifically for the WINSINN dual gear extruder to prevent filament from coming into contact with the Z axis rod. I also included a cable tie mount to keep cables organized and out of the way. When installing this part, push it...

Bracket used to align the Filament Runout Sensor with the Micro Swiss Dual Gear Bowden Extruder that is being installed on one of the 3D printers listed below.Compatible with:Ender 3 MaxEnder 3 Max NeoEnder 5 PlusCR-10 V2Use two of the four screws to...

I found that many of the dual gear extruders for the Ender 3 sold on amazon don't fit with many of the direct drive upgrade kits as they expect the stock extruder. I made this spacer to fit the one I bought: the "3Dman Dual Gear Extruder". Please...

Check out this upgraded aluminum dual-gear pulley dual-drive extruder kit compatible with Creality's CR-10, CR-10S, and CR-10S Pro 3D printers, as well as Ender 3 and Ender 3 Pro models:...

Hinged mount for dual extruders on Ender-3 or any other printer with 2020 aluminium profiles. ... BOM: - M3 nut x3 - M4 profile nut x4 - M4x8 screws x4 - f695zz of 695zz bearing x2 - M3x45 screw x1 - M3x40 screw x2

This is a remix of Ender 3 dual cable chain mount for flipped bmg extruder. ...I moved the extruder chain mount to the middle of the plate so the cable doesn't rest on top of the tension screw when the bmg extruder is rotated 180 degrees.

This is a Spacer to raise up the runout sensor if you are using the actual creality runout sensor or bracket spacer raises sensor 8.75 mm so you will need to get some m3 x 25 or 30 screws I found mine m3 x 25 at local Menards the actual Dimensions...

I edited offset and add a support to leveling sensor

That is an attachment part for BTT Smart Filament Sensor to mount it in the right side of an dual geared extruder (those that are red), I made so it sits horizontally because it more easy to print that way, but it minimizes the max z distance of the...

Compatible with Satsana Neo 3 Fan Cage.I used a 23mm stepper (required if you don't want it to hit rail) - I Had to reverse the two center wires on my ender stepper cable (Blue and Green) for this stepper. This one is on amazon for $8.88 at the...

This remix from the original changes the location of the tube hole so that it aligns to the dual gear extruder shown in the photo. The hole placement isn't perfectly aligned, basically eyeballed it but it's close enough since the rubber bushing...

Dies ist ein Filament Guide für meinen Ender 3 V2 Drucker mit Aluminium Dual Gear Extruder. Mich hat es immer gestört, dass das Filament ständig an der Einzugsöffnung entlang schrammt. Deshalb habe ich heute den ganzen kram fast 3 Stunden vermessen...

Ich habe meinen Ender 3 Pro komplett umgebaut: Linear Rail an allen Achsen Direct Drive mit Dual Gear Extruder Alle Teile sind verschiebbar, durch Nuten für M3 Flache Muttern, man kann die Schiene der x-Achse verschieben. Jeder Extruder kann...

Remix of [JamieBK's direct drive mount](https://www.thingiverse.com/thing:4555065) that uses the dual gear drive extruder used with CR10

I needed version for Dual Gear Extruder (https://www.amazon.co.uk/gp/product/B07SY745CF/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1) - it is bit higher and needs longer arm

Sticky_Rice, thanks for the original design! ... I changed the following: - improved the upper part of the radiator cooling channel to make it more "bridge-friendly" - added bltouch mount and wire channel for it - shifted the part cooling fan...

This will work for any Ender 3 or Ender 3 pro using a DUAL GEAR extruder. WILL NOT work with the stock extruder or single-gear extruder! This is a remix file as the original file had issues with the mesh, did not work for my dual-gear extruder,...

CR-10, Ender 3, Ender 3 Pro Direct Drive Mount Aluminium Dual Gear Extruder. Remix from https://www.thingiverse.com/thing:3369418 I used with Satsana Fan duct https://www.thingiverse.com/thing:4377334 ### Installation Remove your X carriage and the...

This part is specifically designed for attaching the stock filament runout sensor of Longer LK4 Pro to a dual drive extruder upgrade kit.\r\n\r\nThe upgraded aluminum dual-gear pulley dual-drive extruder kit can be found here:...

The PTFE hose must be cut as follows:: === PTFE tube from sensor to extruder: 11cm PTFE tube from filament to sensor: 8cm Material list: ==== PTFE Bowden Hose Micro Swiss Bowden Dual Gear Extruder Creality Filament Runout Sensor Kit Filament I have...

...If you haven't already upgraded to the Capricorn Bowden PTFE tubing, now is a great time - it's a fantastic upgrade over the OEM bowden tube that comes with the Ender 3 and has even higher heat resistance too. You can find it on Amazon at this link.