ender 3 direct drive 3d models

Used meshmixer to cut a loading slot into the filament guide by TheLizard - https://www.thingiverse.com/thing:4729328 For those as lazy as me to not want to unload-reload filament just to start using the new guide :) Slot positioning works for me,...

INSTALLATION: You will also need Bantam fan duct from https://bantam.design/ and SpeedDrive mount Swap extruder motor with Y axis motor as it is shorter and has plenty of power to drive extruder, otherwise the shaft of extruder motor will make...

This is a bracket I designed because I got a direct drive extruder, and the mount for the reverse bowden tube is a lot taller than the standard hot end bowden mount. This means that for tall prints the bowden tube will foul on the top part of the...

This is a complete redesign of the Drivinator for my ender 3 v2. This fits a BMG extruder.The purpose of the slots holding the motor is to make maintaining the hotend easier. The idea is that you don't use a coupler on the BMG. Instead you used the...

I haven't printed or tested these yet, so if there's anything that needs tweaking or revised, please let me know. ... This is a remix of napfkuchen's Direct Extrusion Mount, with some key adjustments made to the length and added supports.

- Swap the extruder motor with the Y axis motor, which is shorter and has plenty of power to drive the extruder. Otherwise, the shaft of the extruder motor will prevent it from mounting part cooling fans. - Add M5 washers between each sleeve and...

You can use the M3*6mm screws that come with the CRTouch and screw them directly into the mount from the bottom just like the factory mounts (holes are 2.6mm for a self tapping fit, you may need to adjust your hole size offset in your slicer or...

Testing completed and it's working great, but you'll need to extend the E Wiring slightly to allow movement in the X direction. With this mod, I've managed to bring retraction down to 2mm or even less. There is a slight tilt to the mount, so I'm...

3 @16.1.2021 Cable holder added ####Rev. 2 @ 6.1.2021 Few small modification in the source files. BLTouch offset: -27,2mm in X; -31,4 mm in Y. Z axis is up to you (please follow manufacturer instruction). ####Rev. 1 Both body parts are screwed...

3 @16.1.2021 Cable holder added ####Rev. 2 @ 6.1.2021 Few small modification in the source files. BLTouch offset: -27,2mm in X; -31,4 mm in Y. Z axis is up to you (please follow manufacturer instruction). ####Rev. 1 Both body parts are screwed...

3. Install the carriage plate + clip + extruder holder (+screws). 4. Attach the FANG to the carriage plate (+screws). (EDIT: Make sure the holes are lined up properly, and maybe it's best to squeeze the plastic parts together with your fingers while...

This remix adds strain relief and other accessory mounting holes to the speedDrive mount.

just a thing i made to guide filimentprint without supportorient on the flat side

I've added a fan holder to my new setup, eliminating the need to remove the original fan. You're free to customize it with a more powerful fan if you choose to do so. ...Check out this video for reference: https://youtu.be/iw0XqjiyDb8

Made one side flat so for easier printing. ... Category: 3D Printer Parts

Made from PETG with 50% infill

V3 is updated with a sleeker appearance. Remix where I downsized the tank and refined its design. I utilize the trianglelap E3D V6 from https://www.aliexpress.com/item/32844028127.html?spm=a2g0s.9042311.0.0.27424c4dajthw2. The trianglelap...

This remake was crafted to facilitate the utilization of the silver Creality extruder. ...A section with an extremely narrow wall exists, yet it prints and functions flawlessly both with and without "Detect Thin Walls" activated as demonstrated in the...

Installs on the extruder stepper shaft with a small magnet.

I did nothing more than remove the drag chain part, and add insets for the nuts for the BLTouch.

a simple remix with a support for bltouch https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller...

I needed to make some adjustments to the nozzle fan because my current nozzle was a bit too short, so I decided to give it a height boost. As often happens when making small changes, I got carried away and ended up modifying more than I intended. I...

Did not like the Bare Extruder motor look so i designed one with the Dragon logo.

Made one side flat so for easier printing.

<p>This is remix of this file from Thingiverse: <a href="https://www.thingiverse.com/thing:4376882">https://www.thingiverse.com/thing:4376882</a></p><p>You will need: 2x M4x10 screws<br>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;...

This remix rotates the extruder 90 degrees to bring the weight closer to the x-axis carriage, maintaining clearance from the frame and preserving z-axis capability. The stepper motor spacer is identical to that of the original adapter, requiring two...

You can use this cover on any other printer..

Installs on the extruder stepper shaft with a small magnet. ... Category: 3D Printer Accessories

Print it in 100% scale to move it easy, and print it in 101% scale to make movement harder.