ender 3 direct drive kit 3d models

... and quality is there! Benchmarks: Ender 3 with double Z-axis, E3DV6 full direct type Prusa extruder head, MKS_Gen_L motherboard, TMC2208+LV8729 drivers for the extruder, Noctua fan....and Ikea Lack Enclosure to print everything... ...EXTRA!

This conversion transforms the Dual Drive extruder duplicate into a direct drive. Requires updating the e-steps to approximately four hundred. ... It is a remix of Blyckert's adaptation for the original extruder.

Having upgraded my Ender 3V2 to diy direct drive, I need something to restrain the hotend cable without installing an elaborate x-rail cable chain. So I come up with a sliding bearing ring, mounted on the underside of the top rail, through which the...

This is a filament guide to be used together with the filament dry box for Ikea Samla when your Ender is converted to direct drive. ... Filament storage: https://www.thingiverse.com/thing:3638817 Parts needed: - 5 pcs [Pneumatic...

The component I'm looking at appears to be an essential part of guiding the filament directly into my extruder, which utilizes a direct drive system. ...The filament itself is secured to a sturdy wall-mounted fixture.

This is a DIY Ender 3 Direct Dual Gear Extruder Upgrade. The extruder itself is a budget-friendly €15 component. To get the best results, you'll need to adjust your E-steps to 141.9mm. On top of that, I'm using a Creality 3D 42-34 stepper motor...

This is an expanded edition of the original direct drive mount submitted by BenAwWhite. ...It's been engineered to complement the four-wheel X carriage offered on Amazon seamlessly.

I've designed a direct drive mount that resists bending during retraction, thanks to its reinforced structure. ...I pair it with the Cyclone V5 fan duct and suspect it could also be compatible with other models.

7/6/21- Direct drive is still off. working on new design all together. source file - https://www.thingiverse.com/thing:3589452 Had to modify the design. Extrude was off by 6mm to hot end. ... Added EGA

I found the original versions worked great... ...so of course had to remix. Incorporated the extruder housing into the part and added some PTFE tube direct from drive into hot end.

Just a small piece that helps me to guide the filament to my direct drive extruder. The filament spool is mounted on a wall mount. ... Category: 3D Printer Parts

resized the knob end to be smaller to accommodate the smaller space with the direct drive setup. the shaft hole was left unchanged but didnt fit without filing etc. the hole was to small. Palodion... ...thanks for the design.

Sliding Filament guide for Ender 3 printers that are Top Fed through a case. You can have multiple feeds. Slides into the T-Rail. ...

Ender 3v2 Directdrive mount

A direct mount to the Ender 3's gantry is provided, utilizing the stock 40mm fan for part cooling. To attach, two washers are required. Note that it does consume approximately 5mm of Y-axis space. Much more is yet to come, so stay tuned! Enjoy! Four...

Too many times I have found myself having to dismantle my hot end assembly in order to remove the direct drive mount just to take care of a clogged nozzle or an extruder gear issue. But not any more! I present to you, Thingiverse community, a...

I designed a replacement for the original Ender 3 e-plate in order to mount a BMG directdrive extruder. ...For assembly of the 3D-printed parts you need m3 threaded-inserts and screws.

I remixed the original to work with the original Ender 3 extruder. ...Currently this is only the version for heated inserts if you need other versions as well write me a comment.

This raises the spool holder up 2 inches so that you don't lose print height with your direct drive motor hitting the spool. ...It needs supports for the tab that goes over the hole, it does not need supports in the holes themselves.

I combined stiggan2k's awesome angled direct drive extruder adapter adapter_angled_v2_one_piece.stl and stepper_spacer.stl from https://www.thingiverse.com/thing:4459700 with the ExtruderFix from w0kk3l https://www.thingiverse.com/thing:4717392. ... ...

This part i created because i converted to direct drive and there was an empty spot where the extruder motor was. I use a side mount for my filament so this part guides the filament from the side to the extruder. ...There is also a sort of hinge to tie...

This will keep the cable for direct drive conversions to be out of the way of the prints and also the heated bed. It should be able to attached with the included screw to the old extruder mount. ... Edit: Added a version with a bigger hole and angle...

So the Ender3ProBullseyeDuct10.19 is not compatible with the Creality Direct drive; the stepper motor blocks where the fan goes. So I extended the ducting out so that it fits.I printed in ABS; but you can print in PETG or PLA/PLA+. ...I recommend...

I've modified the Direct Drive Adapter from Blyckert. I've removed some material for improved cooling of the Stepper Motor and made the holes for small screws slightly larger so they fit better into place. Overall, it works well without any...

This will keep the cable for direct drive conversions to be out of the way of the prints and also the heated bed. ...It should be able to attached with the included screw to the old extruder mount.</p> <p>Edit: Added a version with a bigger hole and...

... ... The remixed knob has been extended for seamless use with my direct drive, accessible at https://www.thingiverse.com/thing:4459700. ...Additionally, I refined the design by reducing its thickness to 5mm and incorporating strategically placed holes.

I use a direct drive hot end and found that I needed to keep the filament ‘high up’ and inside the print volume, I’d been using a piece of twisted wire for months no finally got around to designing something for the purpose.Added a v2 that is rounded...

...I strongly advise against printing this version for a standard Ender 3. For stock models, please refer to Thingiverse: 3562807. Important note: If you're planning to print with high-temperature materials like PLA, don't use the original PLA shroud.

Hello everybody!This is an adapter to fit a dual-gear system onto the official creality ender3-direct-drive x-carriage.My problem was, that the aluminum parts of the dual-gear system didn't fit the old x-carriage.So I made 3 parts:DirectDriveSpacer -...

I designed this to use a direct-drive Bulldog extruder. You'll need various 3mm and 6mm hardware, as well as an all-metal 6mm hot end tube (I have a Micro Swiss clone that I'll swap if there's an issue). You'll need to notch your gantry carrier...