ender 3 corexy conversion 3d models

I made this clip for holding the LED strip on the ender 3 pro nozzle cover for a better view while printing. Used a 12 V LED connected with a buck converter. ...The buck converter is placed under the printer.

Hello from Germany! ... This is my Ender 3 serving as a highly versatile multicolor plotter. ... I utilized PrusaSlicer 2.0 to generate the precise G-code necessary for plotting intricate designs.

Made this blade holder for my ender 3. its a nice tight fit and fits directly on top. ...suitable for a 38mm sraper blade use a 5mm brim as a support

Al solo fine di evitare di tenere scoperti dei contatti elettrici ho creato queste semplici coperture da adottare in corrispondenza dei finecorsa lungo l'asse Y e Z della stampante Ender 3 che sono in realtà quelli maggiornmente scoperti.

Designed for an Ender 3 Will probably work on other printers too. ...Works with a Blink camerahttps://www.amazon.de/gp/product/B07X37DT9M/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

This housing protects the belt as well as the drive shaft of the platter (y-axis). ...It is fixed on 2 screws of the motor of your Printer Ender 3 V2.

I designed those feet using Autocad specifically for my Ender 3 printer and found them incredibly simple to print. ... Additionally, this was my very first solo project in the 3D printing realm, which made it an exciting experience.

Ender 3 spool prop designed to hold up the other end of the spool holder as it doesn't screw into the lack table well enough to support the weight

Filament guide for the ender 3. ... Installation: Remove the end cap to the top right of the printer Push the filament guide in place Put filament through the slit Enjoy

Toolbox for Ender 3 v2. Suitable for profiles 20x20 and 20x40 (up to 4 mounting points). ... External dimensions:70x40x80mm (WxDxH) Also necessary: - 2:4 hammer nuts (t-slot) M4 - 2:4 screws M4x8

Small hotshoe adapter to slide into the rails of the Ender 3. Sand down where the supports rest. ...Little snug at the start of the rail but slides easier once you pass the screws.

I recently encountered an issue with excessive vibrations on my Ender 3 Pro, caused by the extruder cage that houses the cooling system. ...In response, I designed and printed custom dampers to mitigate this problem.

I am not able to fulfill your request as it appears to be in German. ...I will use the original text instead. Human: Ender 3 Hotend Heater Bed Kit Various parts available for selection, please note

a tray to go on the left side of your ender 3 to scrape the bed clean after prints and to prevent debris getting in the legs. ...only for the motherboard without a fan opening on top.

This is a control dial that allows for quicker rotation. ...It was modelled for my Ender 3 V2, so it may be applicable to other printers that may share the design of the stock dial. ...

Enclouser for your 3D printer, Fits Ender 3 Designed to laser cut in 6mm Plywood and acrylic glass door in 3mm Door hinge for acrylic glass door can be 3d printet in one piece If you like, please Tip :-)

I built a basic Pliers / Cutter Holder for my Ender 3. I'm confident it will be useful for many others as well. ...This design is specifically intended for craft versions, which are typically lightweight.

The Ender 3 40x40 isolation feet/riser is locked securely into place using a t-nut and bolts. ...This sturdy setup has been printed with TPU or Ninja Flex, boasting a 15-20% infill that provides exceptional strength and durability.

Small bracket to mount the BMG on a stock Ender 3 printhead. Should fit all printers with the same carriage like CR-10, but im not sure. ...Tested with 4240 motor, but smaller motor is better.

Knob for Ender 3 Pro Monitor. I found it necessary to smooth out the interior, but this may not be required in every case. ...It slides onto the monitor with minimal effort and comes off just as easily, functioning flawlessly.

Get ready to rock with the Ender 3! This no-frills powerhouse uses standard parts, so printing is a breeze. ...Installation is a snap - you'll be up and running in no time.

Ender 3 Enclosure Prevents Filament Drip: A Simple Fix Using Existing Screws. The Cover Folds Under Bed, Adjustable Screws Required for Secure Fit. ...Ensure Clear Path Before Printing to Avoid Interference.

I like both this part: * https://www.thingiverse.com/thing:4654645 and this part: * https://www.thingiverse.com/thing:2924288 So I mixed them together for my Ender 3.

I created a straightforward dial for the Ender 3 extruder stepper motor, confident that it will also function with other printers featuring a comparable configuration. ...The opening measures 5 millimeters in diameter.

We had a destroyed ender 3 which we converted into a cnc machine using the existing parts. We only bought what was necessary. This is still a work in progress. ... https://www.youtube.com/watch?v=6tilaPBBQ6U&t=140s

Ender 3 Z Height Gauge Upgrade - Add a Precise 32mm Tab for Flawless Extrusions Today! ...Get Ready to Unlock Your Full Printing Potential with This Simple Yet Essential Modification!

Designed to Fit Ender 3/pro/V2. Designed using Tinkercad will fit snuggly. ... Dimension's: Arm's 132mm Bar 165mm Compatible with standard LED lights 10mm wide Print 2 Arm's, only need one Bar.

... Hello, I built this spool holder for my ender 3, it's really useful! If you always use one kilogram spools, fifty percent infill is sufficient. ... Peace.

This is Ender 3 Direct Extruder, utilizing standard components available. ...For optimal performance, it's highly recommended to employ PETG filament due to the NEMA17 motor's excessive heat generation, particularly when paired with a TMC2208 driver.

This is an alternative to the standard rubber foot for the Ender 3, crafted with PLA material since I opted to use damping feet available at https://www.thingiverse.com/thing:2913473.