ender 3 cooling fan upgrade 3d models

This remix adds a clip to hang it off the fan casing. Print with no support, added a custom support for the clip. ...Cut off the support part with a knife or cutter after.

I need this mod because the stock fan of 6cm was way too loud. I have a wooden box, and I need to lower the heat inside, but outside the noise is keeping me awake at night. I added a voltmeter and modified the grid to make it even more durable. The...

It enables the installation of a 120mm fan as a substitute for the small noisy stock fan. I'm utilizing a Cooler Master Pro 120, which features RGB LEDs. I integrated them into the existing string on my printer to add an extra touch of flair! ...Tips...

Fits Satsana duct perfectly with stock Ender 3 hotend fan. You will need 4x 3/4 inch screws for construction. I used Machine screws found at a local hardware store that were #6-32 x 3/4 inch. They are slighly bigger than the stock M3 screws so use at...

... through the Pi and the bottom part. The side holes are for the M3 T nuts or (https://www.thingiverse.com/thing:4568590) to be place on the V-slots of the Ender 3. This is meant for an Octopi. ... Image bypass: https://imgur.com/gallery/DM03yDO

10-24-19 Update: Enhanced model features increased clearance within nozzle and optimized mounting holes for precise alignment toward nozzle.\r\n\r\nRecent adjustment since 10-9-19:\r\n-\Improved mounting hole clearance for added leeway in mounting...

I remixed BHMarten's design to remove the cable holder and ender 3 logos. ...Just a personal preference.

This fang is designed for a 40mm hotend fan and a 60mm part cooling fan. I'm using Noctua 40x20 and 60x20 fans. For mounting the fans you need 4 x M3x30 and 4 x M4x35 countersunk screws. You may need to run an M3 and M4 tap on the screw holes for...

I used 3M heavy duty double side tape to secure the fan duct/shroud to the y-axis sensor housing (next to the stepper itself) only needs tape fan and screws to secure the fan to the duct. There are internal wind vanes to ensure proper position...

I updated BHMarten's design by stripping away the cable holder and Ender 3 logo, opting for a cleaner aesthetic that suits my taste.

I created a modification of the standard hotend case for the Ender 3v2 NEO so that a quieter and more efficient 40x20mm fan can be mounted. I recommend printing the front wall down with a small support under the punisher logo. ... This is the first...

This is a remix of https://www.thingiverse.com/thing:4284278, which is a remix of https://www.thingiverse.com/thing:3594440 Added a tab so it fits better. ... Specifically for Ender 3 (Pro) printers.

Ender-3 Max Blower cover to replace original/broken blower/fan cover. Designed to replace the original. This print is very delicate due to it needing to be so thin to fit -- it is easy to break and warp. I also printed this with and...

I've been running a Fang fan duct for a while now, but after considering switching to a direct drive setup, I realized that the high, top-mounted fan would obstruct my extruder. So, I drew inspiration from the Ultimaker 2 fan configuration. My...

This is probably one of my favorite version of a duct for the ender 3, decided to add it on here to help those who may find it helpful.[Originally Uploaded by: KingYS on Thingiverse][Original Description]Print Settings:100 % infillstandard 0.2mmABS,...

KP08 upgrade for ender 3 v2

KP08 upgrade for ender 3 v2

... (like shown in picture). I have fasten two parts by self-tapping screws. Just because I have no cylinder M3 screws now :) Update 08.01.2023: Add fan connector version 2. ... Have changed the mounting hole for the fan, for a more secure fit.

The fan vent is now perfectly aligned with the standard fan. Resolution set at a precise 0.2 units. The infill density has been adjusted to span between 60% and a maximum of 100%. Supports are no longer necessary due to optimal part design. ... No...

This part design has yet to be put through its paces thoroughly...\r\n\r\nTo put it through its paces, you'll need:\r\n\r\n1x 4020 blower (centrifugal fan) equipped with a 5-foot lead\r\n3x M2 screws, approximately 18mm in length depending on the fan...

fan duct remix to fit a stock ender 3 cooling fan

... I've created an attachment that's easy to install. Simply print both components without supports and then attach them together using the fan duct. ... Before setting this up, make sure to remove the small built-in support from the bottom part.

I've successfully manufactured three custom rail components for the Ender 3 printer and have upgraded its Y-axis with adjustable end stops as of October 27, 2018.

upgrade

Creality Ender 3 Pro yükseltme valf kolu

Superior Filament Guide for Ender 3.

Cooling system for Ender 3 printer. I designed the model using the original wheelbases and 1 original fan, the other two fans are the vortex model DF501512SH. ...with this modification, the air flow is better conveyed to the nozzle, improving the final...

I made these for my Ender 3 Max, but they also fit on the Ender 3 Pro and the original Ender I believe. Not sure about how they fit on the V2, but someone should try. Added a few 3mm nuts and bolts and had to use a longer 10pin Display cable and a...

buy this and ender website

Accessorize your Ender 3 with a Japanese Torii gateway aesthetic. You will need to print 1 Middle piece either longer or shorter depending on your printer and 2 Side top and bottom pieces. For the Gakuzuka you can choose from 3 characters provided...