ender 3 cooling fan duct 3d models

For model and more details:https://www.printables.com/model/729595-ender-3-pro-dual-4020-fan-ductSo I was on the hunt for a long time for a Fan Duct for my Ender 3 Pro that would work with a dual 4020 fans setup, in order to install some silent fans....

PayPal account: beagleinside@gmail.com Paypal.me link: https://paypal.me/adarkstudio Thank you page: https://pastebin.com/raw/gTt8iE5a Regards Antonio In the attempt to quiet my Ender 3 Pro, I designed this hotend fan duct to use 4010 or 4020 silent...

Add BL Touch Attachment for Satsana Ender 3 Fan Duct\r\nFor Enhanced Precision and Print Quality\r\n\r\nI modified the original design from https://www.thingiverse.com/thing:4373721 by Leesirc to fit perfectly with the BlTouch v3.1, eliminating...

This is fan duct upgrade for the stock Ender 3 S1/Pro fan or Sprite pro extruder. ChangelogUpdate: Aug 2,2022Updated the file with support for resin.Print with hightemp resistant filamentor print it using resin printer for better air flowAdded Stl...

Flying Bear P905 Cooling Fan Duct Fitted with a Powerful 25mm 12 Volt Fan.

I created a custom design for use with the Ender-3's power supply fan, scaling it to meet specific needs. WARNING: The internal voltage of the power supply is lethal and must be treated with extreme caution. Users are strictly prohibited from...

In the meantime, here's my two-fan design, which outperforms the AIRO family: Ptairoductylus https://cults3d.com/en/3d-model/tool/ptairoductylus-a-performance-based-ender-3-cr10-maybe-5-dual-fan-duct Update 3: Added BLTouch Mount STL Print it at 0.24...

This is my design for the Ender 3S1 Fan duct based on this design: https://www.thingiverse.com/thing:5238521 The only difference being that there is no screw required (you will have to use the original screws that was used to mount the extruder),...

Stock ender 3 remix fan duct from submano's upload. Adjusted left exhaust 3mm to the left and lowered entire assembly 3.2 mm for better airflow. Added support to prevent heat sag on the shroud even when printing with PLA. Removed unnecessary...

The Fan Duct Ring fits perfectly in place with a deliberate gap on both the extruder side and nozzle tip side; I'm still awaiting the outcome but expect it to function as intended. ... I printed this part using a 0.1mm layer height and a solid 100%...

I created a fan Duct for Ender 3 hotend that can also be added some led light from an old led strip. Optimized airflow and compatible with silicone cup in the nozzle (easier to change the nozzle) Use it, test it.. enjoy it :) Pint no supports.. I...

I remixed the remix, because the improved duct won't fit on the Ender 3. ...So this has the improvement, but with the original size.

Remix of Gabriel3DCaster's "CR-10 Fan Mod - Airflow Optimization" I redesigned the original setup because it was bumping into my Ender 3 Pro's silicone cover, causing warping issues. ...To resolve this problem, I modified it to be slightly taller,...

Easy-to-print and efficient modular fan duct for Ender 3 / CR-10 printers. At the moment I drew a versions for using direct stock extruder / [direct Gratch extruder](https://www.thingiverse.com/thing:4669524) / Bowden and two 4010 turbine fans...

The modifications I made were extending the duct down a couple millimeters, widening the duct openings at the end, angled the duct opening, and changed the fan mounting screw holes to use M3 bolts and nuts.I have this mounted to an Ender 2 pro that I...

This is something I came up with as a fun side project. ...It's a fan duct that allows the use of 40mm axial fans as part cooling fans. ...The results are surprisingly good, but it's not meant to be a replacement for a proper blower fan.

Upgrading the cooling fan duct involves a clever twist on the standard approach by aiming for the nozzle instead of its traditional placement. ...To execute this modification effectively, it's crucial to introduce structural support solely through the...

This is fan duct upgrade for the stock Ender 3 S1/Pro fan or Sprite pro extruder. ChangelogUpdate: Aug 2,2022Updated the file with support for resin.Print with hightemp resistant filamentor print it using resin printer for better air flowAdded...

This is my design for the Ender 3S1 Fan duct based on this design: https://www.thingiverse.com/thing:5238521The only difference being that there is no screw required (you will have to use the original screws that was used to mount the extruder), this...

... further from the heatbed. (updated after tip that there was a gap) The bridge test is done with PETG at 50mm/s LH=0.2mm,0.65with Fan at 75%, without the special Cura settings for bridging. ... Bridge test: https://www.thingiverse.com/thing:476845

... up to 240 C. Because sock leaves uncovered the upper portion of hotend. This duct install over stock fan and properly directs air flow to the coldend. You get stable temperature, and better cooling for the cold end portion. ...It prevents heat creep

I remixed this fan duct from Ninestar's remix in order to make it fit my printermods.com v1.3 direct drive kit and microswiss hot end. I removed a few mm off the top, moved the duct outlets down 3 mm, and moved the screw holes 1.5 mm to the right for...

This thing is a duct for mounting three 5015 blowers on the x-axis gantry of an Ender 3 Pro. I used six #8-32 x 1" long flat head socket cap screws and #8-32 brass nylock nuts to mount the fans to the duct and standard M4 T Slide Nuts for 20-20...

I designed a custom cover plate featuring the iconic Ender Dragon logo to perfectly complement my Satsana Fan Duct project. Secure it with a precise drop of superglue or hot glue for a seamless attachment. ... Check out the original fan duct I crafted...

Rediseño de Manta https://www.thingiverse.com/thing:4403017 y https://www.printables.com/es/model/169185-manta-compact-fan-duct-tool-change-system de BoothyBoothy para mi Ender 3 pro, quería utilizar los ventiladores de fábrica y adaptar otro del...

Here is a remixed version of this great fan duct for the Ender 3. I have had very good success with this duct and did not want to ditch it when I added the direct drive mod (https://www.thingiverse.com/thing:3386628). I also wanted to add a bed...

It will take about 8 hours and 45 minutes and about 70 grams of PLA. InstallationTo Install this fan duct you only need 2 M3 screws that are already holding the original fan shroud and for the hotend (4010) fan you can use original screws too...

******************************************* [ORIGINAL] This is a very compact double fan duct for Creality Ender 3 / CR10 printers. It is designed to mount on base mount from this Petsfang Duct by @dpetsel: https://www.thingiverse.com/thing:2759439...

Hot End Fan Duct for Stock Fans: CR-10S and Ender 3 Compatible. This design channels all air flow directly onto the heat sink, maximizing efficiency without compromising on simplicity or ease of maintenance. Things to Consider: Supports are...

... to enclose the upper fan, providing extra support in case the fit is not perfectly snug. Finally, an adapter has been incorporated to accommodate 40x40x20 part cooling fans, allowing for flexibility with fan ducts or direct replacement if desired.